gefran 650 Abbreviated Manual page 3

4.19. MODE Submenu - Configuring functioning mode .............110
4.19.1. PID.G.N - Number of groups of control parameters 111
4.19.2. MA.AU - Defining transition from Manual to Automatic .
111
4.19.3. AU.MA - Defining transition from Automatic to Manual .
111
4.19.4. LO.rE - Defining transition from remote SP to local SP .
111
4.19.5. On.OF - Enabling software on/off ............................112
4.19.6. MA.P.L - Enabling manual power latch ....................112
4.19.7. MAn.P - Enabling change of manual power value ...112
4.19.8. dIG - Defining type of digital inputs .........................112
4.19.9. ALRM.N - Number of alarms enabled ......................112
4.19.10. tMEr - Enabling Timer function ................................113
4.19.11. MUL.SP - Enabling Multiset function .......................113
4.19.12. SP.REM - Enabling the remote setpoint ...................113
4.19.13. SPr.t - Defining absolute or deviation remote setpoint ..
113
4.19.14. PROGR - Enabling the setpoint programmer ..........113
4.19.15. t.Pro - Setting the programmer base time ...............114
4.19.16. ENERG - Enabling the energy counter function.......114
4.19.17. T.SAMP - Main input sample time ...........................114
4.19.18. FREQZ - Defining power line frequency ..................114
4.20. TIMER Submenu - Configuring timer parameters .............115
4.20.1. F.tiM - Selecting Timer function mode .....................116
4.20.2. St.St - Selecting the Start/Stop timer command .....116
4.20.3. S.S.t - Defining the Start/Stop timer command logic ....
116
4.20.4. rESE - Selecting the Reset timer command ............116
4.20.5. rES.t - Defining the timer reset command logic .......117
4.20.6. BAND - Band for timer count ...................................117
4.20.7. End - Selecting the function activated at end of count .
117
4.20.8. TIMER - Timer value ...............................................117
4.20.9. MSG.TM - Selecting the message assigned to the
active count .............................................................118
4.22. SERIA Submenu - Configuring serial communication .......121
4.22.1. CODE - Identification code ......................................122
4.22.2. KBAUD - Selecting communication speed ..............122
4.22.3. PAr - Selecting parity ...............................................122
4.23. HMI Submenu - Configuring the display and keypad .......123
4.23.1. but.1 - Selecting function key 1 ...............................124
4.23.2. but.2 - Selecting function key 2 ..............................124
4.23.3. but.3 - Selecting function key 3 ..............................124
4.23.4. dS.SP - Selecting the SV display .............................125
4.23.5. dS.F - Selecting the F display ..................................125
4.23.6. bArG - Selecting the bargraph display ....................125
4.23.7. MSG.LO - Selecting the message assigned to Low 126
4.23.8. MSG.HI - Selecting the message assigned to HIGH .....
126
4.23.9. MSG.ER - Selecting the message assigned to Err .126
4.23.10. MSG.SB - Selecting the message assigned to Sbr .127
4.23.11. LAnG - Selecting language for messages ...............127
4.23.12. SPEED - Message scrolling speed ..........................127
4.23.13. BACKL - Backlighting level ......................................127
4.23.14. QUICK - Quick configuration menu .........................128
4.25. US.CAL Submenu - User calibrations ...............................131
4.25.1. U.CAL - Selecting the user calibration .....................132
4.25.2. FI.CAL - Resetting the factory calibration ................132
4.25.3. C.LOW - Calibrating minimum current / voltage ......132
4.25.4. C.HIGH - Calibrating maximum current / voltage ....133
4.25.5. RTD.LO - Calibrating minimum resistance value .....133
4.25.6. RTD.HI - Calibrating maximum resistance value .....133
4.25.7. HOUR - Setting hours ..............................................133
4.25.8. MIN - Setting minutes ..............................................133
4.25.9. SEC - Setting seconds .............................................134
4.25.10. dAY - Setting day of week .......................................134
4.25.11. DATE - Setting day ...................................................134
4.25.12. Mont - Setting month ...............................................134
4.25.13. YEAR - Setting year .................................................134
4.25.14. C.LO - Setting analog output minimum ...................135
4.25.15. C.HIG - Setting analog output maximum ................135
2
40524-04 Rev0
Gefran 650/1250/1350 Temperature Controller - Abbreviated Manual
4.26. PASC1 - Setting level 1 password 1 ..................................136
4.27. PASC2 - Setting level 2 password 2 ..................................136
4.28. FI.CFG - Entering the reset code .......................................136
5. Examples and application notes .........................
5.6. Alarms ................................................................................142
5.6.1.
5.8. Switching the software on/off ............................................144
5.8.1.
5.8.2.
5.9. Soft-Start ............................................................................144
5.10. Tuning .................................................................................144
5.10.1.
5.10.1.1.
5.10.2.
5.10.3.
5.10.4.
5.10.5.
5.11. Timer ..................................................................................147
5.11.1.
5.11.2.
5.11.3.
5.11.4.
5.13. Setpoint programmer .........................................................149
5.13.1.
5.13.2.
5.13.3.
5.13.4.
5.13.4.1.
5.13.4.2.
5.13.4.3.
5.13.4.4.
5.13.4.5.
5.13.5.
5.13.6.
5.13.7.
5.13.8.
Generic alarms AL1...AL4 .......................................142
How to switch it off ..................................................144
How to switch it on ..................................................144
Tuning actions ..........................................................144
Influence of Proportional, Derivative and Integral actions on
response of controlled process ....................................... 144
Manual tuning ..........................................................144
Self-Tuning ...............................................................145
Auto-Tuning ..............................................................146
Examples of tuning ..................................................146
Start/Stop Timer.......................................................147
Stabilization timer ....................................................148
Start timer ................................................................148
Variables available for the user configuration menu 148
What is a program ....................................................149
Programmer functions .............................................149
Programmer behavior ..............................................150
Program examples ...................................................150
ONE STEP program ......................................................... 150
ONE STEP program ......................................................... 150
Program with assigned events ......................................... 150
Cyclical program with 3 setpoints and 3 steps ................ 152
Program with HBB (hold back band) function ................. 152
Fast simulation of program ......................................152
Controlling the program from the ...................................
.......................................................................................
.......................................................................................
keypad .....................................................................152
Programmer Reset mode .........................................152
Restart with step search ..........................................152
137