Related Manuals for LOGICDATA SILVERstandard
Summary of Contents for LOGICDATA SILVERstandard
- Page 1 SILVERstandard The SILVER Series by LOGICDATA OWNER’S MANUAL adjustables.logicdata.net...
-
Page 2: Table Of Contents
No part of this manual may be reproduced me- chanically, electronically, or by other means, in any form, without prior written permission of LOGICDATA Electronic & Software Entwicklungs GmbH. Violations involving copyright may result in legal action. -
Page 3: Safety
▪ Do not operate the product unless it is in full working order ▪ Do not remove, change, bridge, or bypass any protection or safety features ▪ Do not convert or modify the LOGICDATA SILVERstandard without written approval from the supplier ▪... - Page 4 04 // SILVER SERIES OWNER’S MANUAL...
- Page 5 SILVER SERIES OWNER’S MANUAL //...
- Page 6 INTENDED USE The LOGICDATA SILVERstandard is an electrically controlled Bed Frame. It may be used solely for its intended use according to this documentation. The LOGICDATA SILVERstandard is designed for indoor use and household use only. Outdoor use is forbidden. The Bed Frame is operated by a Remote Control. It features a USB Module on each side, which can be used to charge mobile devices such as smart phones or tablet PCs.
- Page 7 ▪ Do not let children or animals climb on or under the Bed Frame ▪ Do not use the Bed Frame without a mattress ▪ Do not overload the Bed Frame (max. load is 700 lbs evenly distributed) ▪ Do not operate the Bed Frame continuously NOTICE The Bed Frame is not designed for continuous operation.
- Page 8 Never operate the Bed Frame if its Cables or plugs are damaged, or if it displays obvious defects • Consult LOGICDATA for further instructions if the Bed Frame is damaged in any way, in ac- cordance with the product’s Limited Warranty •...
- Page 9 Moderate risk of death or serious injury Opening electrical components, or attempting improper conversions or modifications to electri- cal or mechanical components on the LOGICDATA SILVERstandard may lead to death or serious injury. • Do not convert or modify the LOGICDATA SILVERstandard •...
- Page 10 WARNING Moderate risk of death or serious injury through electric shocks Leaving the Bed Frame plugged in while mounting or demounting components may lead to death or serious injury through electric shocks. • Always unplug the Bed Frame from the mains before mounting or demounting components WARNING Moderate risk of death or serious injury to children Operating the Bed Frame when children are close by may lead to death or serious injury to...
- Page 11 FCC statement The wireless working frequency for this product is 2.4 GHz FCC Compliance The LOGICDATA SILVERstandard complies with FCC CFR 47 Part 15 Subpart B/C. Operation is subject to the following conditions: 1. The product may not cause harmful interference 2.
-
Page 12: Introduction
Thank you for choosing a product from LOGICDATA. With the LOGICDATA SILVERstandard, you can be sure that every effort has been made to en- sure your comfort and safety. The Bed Frame has been rigorously tested and complies with all relevant safety standards and their requirements. - Page 13 LIABILITY The descriptions of product characteristics in this Owner’s Manual are not a guarantee of the presence of these characteristics. LOGICDATA is not liable for damage or injury caused by: ▪ Improper product use ▪ Disregard of the documentation ▪ Unauthorized product alterations ▪...
-
Page 14: Box Contents
BOX CONTENTS The LOGICDATA SILVERstandard is delivered in two boxes. The boxes contain all the parts and tools necessary to fully assemble and operate the system. Upon opening the packaging, use this checklist to ensure all the parts are included and in perfect condition. If you notice that any part is damaged or missing, contact LOGICDATA. - Page 15 LEG PLATFORM 2x AAA BATTERIES FOOT PLATFORM FOOT QUICK START GUIDE OWNER'S MANUAL 14X MOUNTING SCREW (PLATFORMS) SILVERstandard SILVERstandard The Silver Series by The Silver Series by OWNER‘S MANUAL QUICK START GUIDE *Only with SILVERstandard+ SILVER SERIES OWNER’S MANUAL //...
-
Page 16: Assembly
ASSEMBLY TOOLS AND EQUIPMENT The LOGICDATA SILVERstandard should be assembled by two adults. If you assemble the Bed Frame alone, be careful when lifting heavy parts. No extra tools are needed. Ensure the assembly area is larger than the Bed Frame. Follow the steps carefully to assemble the Bed Frame correctly. - Page 17 TOOL DO NOT REMOVE STRAPPING TAPE Open the internal boxes Take out the Side Rails (A, B) and Cross- bars (C) and lay them on the floor (see DO NOT REMOVE STRAPPING TAPE picture) USE THE LABELS ON THE SIDE RAILS Use the labels on the Side Rails to ensure they are oriented correctly.
- Page 18 CONNECTING THE BARS Move the Crossbars (C) and the Side Rails (A, B) together Ensure that the protruding parts on the Crossbar side of the Corner Con- nector are placed into the holes on the Side Rail sides. Insert the Assembly Tool (TOOL) and turn the Mounting Screw clockwise.
- Page 19 Remove the assembly supports and place the end of the Bed Frame with legs attached on the floor. Lift up the other end and place the Assembly Supports underneath the Crossbar. Screw in the remaining legs (D). Remove the assembly supports. CAUTION Risk of minor or moderate injury Lifting the Bed Frame incorrectly could cause you to lose balance or drop the Bed Frame.
- Page 20 MOUNTING THE HEAD PLATFORM Lay the Head Platform REMOVE ALL STRAPPING TAPE BEFORE (L) across the frame so MOUNTING THE PLATFORMS that its holes are aligned with the holes on the Side Rails (A, B). Insert and tighten the Mounting Screws (P) to fix the Head Platform (L) by hand.
- Page 21 Massage Motor Ca- bles (if supplied) into the Massage Adapter Cable (G). NOTE: If your version of the SILVERstandard is not supplied with Massage Mo- tors, plug the Underbed Light Cable directly into the Plug Port on the Side Rail.
- Page 22 SILVERstandard 12 pin 10 pin 8 pin 12 pin SILVERstandard+ (with Massage Function) 8 pin 12 pin 10 pin Connect the two Side Rails with the Side-to-Side Cable (I) by plugging each end into the appropriate Plug Port. Connect one USB Module (H) on each Side Rail (see below).
- Page 23 To connect the USB modules: Create a loose loop with the USB Cable (H) and run the Cable through the des- ignated channel. Plug the USB Cables into the 2-Pin Plugports on ei- ther side of the Bed Frame NOTICE Ensure that the Power Converter Cable is connected to the white, 10-Pin Plug Port on the Side Rail.
- Page 24 ATTACHING THE USB MODULES Attach the two USB Modules (H) by clicking them onto the Mounting Plates underneath the Base Plat- form. CONNECTING THE POWER CABLE Connect the Power Cable (K) to the Power Converter (J). Connect the Power Cable to the nearest power outlet.
- Page 25 LEVELING THE BED FRAME If the Bed Frame is on an un- even surface, you can level it by adjusting the legs individ- ually. To adjust the height of a leg, turn the lowest part of the leg until the desired height is reached.
- Page 26 PAIRING THE REMOTE CONTROL In order to operate the Bed Frame, you must pair it to a Remote Control. First, ensure the Bed Frame has been unplugged for at least 10 seconds, then proceed as follows: 1. Plug the Bed Frame into the mains. This will automatically switch it to Pairing Mode for 30 seconds.
-
Page 27: Disassembly And Transportation
DISASSEMBLY AND TRANSPORTATION DISASSEMBLY To disassemble the LOGICDATA SILVERstandard, you must first disconnect the Bed Frame from the power source. Then, follow the assembly instructions in reverse order. To minimize the risk of pinch- ing when transporting the Side Rails, secure all moving parts by wrapping packaging tape around the shown areas. - Page 28 Only grip the fixed part of the Bed Frame CAUTION Risk of minor or moderate injury through crushing Tilting the Bed Frame when lifting or moving the LOGICDATA SILVERstandard may lead to mi- nor or moderate injury through crushing. •...
-
Page 29: Operation
OPERATION REMOTE CONTROL The LOGICDATA SILVERstandard comes with a range of different Remote Controls. The Remote Control supplied with your product depends on the model you have ordered. Your Remote Con- trol may include the following Buttons and Indicators: LED Array Shows the function that the Bed Frame is currently performing. - Page 30 SAVING A MEMORY POSITION The LOGICDATA SILVERstandard comes with two saved Memory Positions: Anti-Snore (Position 1) and Zero Gravity (Position 2). You can move to these positions by pressing the Memory Posi- tion Buttons on your Remote Control.
- Page 31 You can change the saved Memory Positions to new Memory Positions that you find more com- fortable. To do this, proceed as follows: 1. Press and hold the UP or DOWN Button for the Platform you wish to adjust 2. Wait until the Bed Frame has reached the desired position 3.
- Page 32 Light on or off, press the Underbed Light Button on the right-hand edge of the Remote Control. OPERATING THE MASSAGE FUNCTION* Certain versions of the Bed Frame (SILVERstandard+) are equipped with a Massage Function. To begin using this function, proceed as follows: 1. Press any of the Massage Buttons on your Remote Control 2.
- Page 33 WIRELESS SYNC MODE The LOGICDATA SILVERstandard’s Wireless Sync Mode allows you to control two Twin XL Bed Frames with one Remote Control. Bed 2 Bed 1 Remote Control 1 Remote Control 2 ACTIVATING WIRELESS SYNC MODE Before you activate Wireless Sync Mode, please ensure: ▪...
- Page 34 NOTICE If both Remote Controls are paired to the same Bed Frame, unplug the Power Converter of the unpaired Bed Frame until the LED on the Power Converter goes out. Then, plug the Power Con- verter back in. Press any Button on the Remote Control you want to pair to the unpaired Bed Frame to complete the pairing (see the section “Pairing the Remote Control”...
- Page 35 FIXING MISALIGNMENT If the two Bed Frames become misaligned (i.e. they are at different heights or positions), you must move both Bed Frames to their lowest position. 1. Press the Sleeping Position Button on one Remote Control. 2. Wait for both Bed Frames to reach their lowest position 3.
-
Page 36: Cleaning And Maintenance
Always unplug the Bed Frame from the mains before cleaning NOTICE Cleaning agents, such as non-alcohol based cleaners, sanitizers, and others can destroy the an- odized layer of the LOGICDATA SILVERstandard. Use only a dry or slightly damp lint-free cloth to clean the Bed Frame MAINTENANCE The LOGICDATA SILVERstandard does not require maintenance. -
Page 37: Possible Malfunctions And Solutions
POSSIBLE MALFUNCTIONS AND THEIR SOLUTIONS BEHAVIOR POSSIBLE CAUSE / SOLUTION Remote lights up but the 1. The Bed Frame is not connected properly. Check the power Bed Frame does not re- connection spond when Buttons are 2. Overheating after continuous use. Ensure that the Duty Cy- pressed. - Page 38 After this action, the batteries must be replaced. If you store batteries in the power supply as a backup, they must be replaced annually. Remote Control defective Press the Button on the Power Converter until the Bed Frame is or lost. in the Sleeping Position.
-
Page 39: Technical Data
TECHNICAL DATA PROPERTY SPECIFICATION Input Voltage 100-240 V Rated Input current 2,2 A Suitable mattress King Queen Twin XL dimensions 76 in × 80 in 60 in × 80 in 39 in × 80 in Ambient conditions Indoor use only Maximum load 700 lbs evenly distributed FINAL DISPOSAL... - Page 40 LOGICDATA Headquarters Electronic & Software Entwicklungs GmbH Wirtschaftspark 18 8530 Deutschlandsberg AUSTRIA Watch the assembly video at LOGICDATA North America Inc. adjustables.logicdata.net 1525 Gezon Parkway SW, Suite C Grand Rapids, MI 49509 Do you need support? Phone: 800-305-1925 E-Mail: support.us@logicdata.net...