LOGICDATA DYNAMIC MOTION System Manual
Hide thumbs
Also See for DYNAMIC MOTION:
- System manual (27 pages) ,
- Configuration handbook (23 pages) ,
- System manual (32 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for LOGICDATA DYNAMIC MOTION
Summary of Contents for LOGICDATA DYNAMIC MOTION
- Page 1 DOCUMENT VERSION 3.0 | JANUARY 2020 DYNAMIC MOTION system SYSTEM manual...
- Page 2 LOGICDATA Electronic & Software Entwicklungs GmbH Wirtschaftspark 18 8530 Deutschlandsberg Austria Phone: +43 (0) 3462 51 98 0 Fax: +43 (0) 3462 51 98 1030 Internet: http://www.logicdata.net Email: office.at@logicdata.net INFO This manual is valid for all configurations of the DYNAMIC MOTION system...
-
Page 3: Table Of Contents
DYNAMIC MOTION SYSTEM - SYSTEM MANUAL // PAGE 3 CONTENTS General information Other applicable documents Copyright Royalty-free use of images and text Trademarks Safety General safety regulations and obligations Intended use Reasonably foreseeable misuse Explanation of symbols and signal words... - Page 4 DYNAMIC MOTION SYSTEM - SYSTEM MANUAL // PAGE 4 Collision Protection Drive Back Function Troubleshooting Possible Problems and their solutions System Information 8.2.1 DMUI-TOUCH-B-UD/DMUI-EASY2move 8.2.2 DMUI-TOUCH-C-FX 10 Additional Information 10.1 Disassembly 10.2 Maintenance 10.2.1 Cleaning 10.3 Disposal...
-
Page 5: General Information
No part of the text and no image may be used without the prior written consent of LOGICDATA. Texts and images may not be sold in their current state, and may not be published or sublicensed digitally. -
Page 6: Safety
In general, the following safety regulations and obligations apply when handling the product: • Do not operate the DYNAMIC MOTION system unless it is in a clean and perfect condition • Do not remove, change, bridge, or bypass any protection, safety, or monitoring equipment •... -
Page 7: Liability
2.5 LIABILITY LOGICDATA products comply with all relevant industry standards, which are listed in the product's data- sheet. However, risk can result from incorrect operation or misuse. LOGICDATA is in particular not liable for damage or injury caused by: • Improper product use •... -
Page 8: Notes For Resellers
Although the DYNAMIC MOTION system was designed with measures to help prevent the Table System from slipping, the risk of uncontrolled movement is dependent on the design of the Height-Adjustable Columns and –... -
Page 9: Scope Of Delivery
Position Reset Procedure for Table Systems controlled by a Handset with an UP Key and DOWN Key (Comfort or Basic Handsets). If your DYNAMIC MOTION system is operated by a different User Interface, consult that product’s operating Manual for instructions on performing a Position Reset Procedure. -
Page 10: Operation
Table System that will be controlled by a Handset with an UP Key and DOWN Key. If your DYNAMIC MOTION system is operated by a different User Interface, consult that product’s operating Manual for instructions on operating the DYNAMIC MOTION system. -
Page 11: Standard Functions
This section describes functions that can be performed using both Comfort and Basic User Handsets along- side the DYNAMIC MOTION system. If your DYNAMIC MOTION system will be controlled by a different User Interface, consult that product's Operating Manual for instructions and safety advice. -
Page 12: Adjusting The Table Top To A Saved Position
Version B (Auto-Movement with double-click function): INFO The double-click function is available only for DYNAMIC MOTION systems sold in US markets. It is not activated as standard. If you press any Key while the table moves to a Memory Position, the Table Top will stop INFO moving immediately. -
Page 13: Software Dependent Functions
This section describes the software-dependent functions that can be performed by Comfort and Basic User Handsets alongside the DYNAMIC MOTION system. If your DYNAMIC MOTION system will be controlled by a different User Interface, consult that product's Operating Manual for instructions and safety advice. -
Page 14: Factory Reset
▸ The Container Stop / Shelf Stop Position is deleted 6.1.4 FACTORY RESET To reset the DYNAMIC MOTION System to its Factor Settings with a Basic Handset: Press the UP and DOWN Keys simultaneously, then release Press and hold the UP and DOWN Keys for 10 seconds ▸... -
Page 15: Advanced Functions
6.2 ADVANCED FUNCTIONS This section describes functions that can only be performed by certain Comfort Handsets alongside the DYNAMIC MOTION system. Consult your User Interface's Manual for instructions and safety advice. 6.2.1 KEY LOCK Risk of minor or moderate injury through uncontrolled movement... - Page 16 Intelligent System Protection (ISP) is LOGICDATA’s collision detection system. It aims to reduce the risk of system damage when using LOGICDATA products. If there is an obstacle in the operating range of a table, and the obstacle and table collide, a load change affects the DYNAMIC MOTION system. When the load change is detected, all Actuators stop immediately and move back in the opposite direction for a few seconds (see 9.2 Drive Back Function).
- Page 17 DYNAMIC MOTION SYSTEM - SYSTEM MANUAL // PAGE 17 8.2 SYSTEM INFORMATION 8.2.1 DMUI-TOUCH-B-UD / DMUI-EASY2MOVE When a DMUI-TOUCH-B-UD or DMUI-EASY2move Handset is installed alongside the DYNAMIC MOTION sys- tem, system information is communicated via flashes of the LED Signal Light. Possible signals are as follows: Signal...
- Page 18 Release all Keys and wait for 5 seconds. Then, try again. Motor Under Voltage Release all Keys and wait for 5 seconds. Then, try again. Do not operate the DYNAMIC MOTION system if problems persist. Contact LOGICDATA NOTICE for further information.
- Page 19 DYNAMIC MOTION SYSTEM - SYSTEM MANUAL // PAGE 19 9 ADDITIONAL INFORMATION DISASSEMBLY To disassemble the DYNAMIC MOTION system, unplug the Power Hub at the mains, then disconnect all cables from the Power Hub. Then, follow the assembly instructions for your chosen product in reverse order. 9.2 MAINTENANCE All DYNAMIC MOTION system Products are maintenance-free.
- Page 20 LOGICDATA LOGICDATA North America, Inc. Broadmoor Ave SE Electronic & Software Entwicklungs GmbH Suite D Wirtschaftspark 18 Grand Rapids 8530 Deutschlandsberg MI, USA, Austria Phone: +43 (0)3462 5198 0 Phone: +1 (616) 328 8841 Fax: +43 (0)3462 5198 1030 Email: office.na@logicdata.net...