Page 3
Revision Date: March 1988 HP References in this Manual This manual may contain references to HP or Hewlett-Packard. Please note that Hewlett-Packard's former test and measurement, semiconductor products and chemical analysis businesses are now part of Agilent Technologies. Changes to this Manual No changes have been made to this manual.
WHAT SAFETY PRECAUTIONS SHOULD I TAKE ...., ....1-2 WHERE SHOULD I KEEP THE 5528A WHEN I'M NOT USING • • WHAT SHOULD I DO If MY 5528A SEEMS NOT TO BE WORKING? . . . • • •...
CONNECTING THE REM OTE CONTROL BOX TO THE MEASUREMENT DISPLAY CONNECTING AN HP PERSONAL COMPUTER AND/OR AN HP PLOTIER TO THE MEASUREMENT DiSPLAy ..........5-6...
Model 5528A Table of Contents Table of Contents (Continued) SECTION STRAIGHTNESS MEASUREMENTS ........10-1 CONTENTS 10-1 • INTRODUCTION . 10-1 ....OPERATING SPECIFICATIONS ........... . 10-1 HARDWARE REQUIRED 10·3...
Page 13
Model5S28A Table of Contents Table of Contents (Continued) AF fECTS ACCURACYI WHAT 11-23 ..la�er System Sources ............ Straishtness Reflector Mirrors .
Model 5526A Table of Contents Table of Contents (Continued) Checking Alignm ent for Beam Strength ......"..13-1 7 Checking for MIs-Alignment between the Llser Beam ;jnd the Optics' Travel Path 13-1 7 Manual Removal of Slope ..
Model 5528A list of Figures List of Figures (Continued) 11·6. Stf:lightncss M easuremenls on HorilOntal · . • . . • • ..• . • • . . " . • . . Figur e Two Dots on the Reflector 11-9.
EQUIPMENT/MEASUREMENT MATRIX HARDWARE LIST HARDWARE G[NERAL DESCRIPTIONS MOUNTING INTRODUCTION TO HP'S 5528A LASER MEASUREMENT SYSTEM The HP 5528/\ laser Measurement System was designed specifically make a variety of very tool accurate measurcments In a machine environment. This User's Guide is Intcnded to hclp you learn to usc...
Model 5528A Introduction Supportfng the specific operating procedures is a body of general "Reference Material". You will have to become familiar with this information, which will be useful you in many of the mEldSuremell1!. you make with the laser Measurement System.
• Parallelism WHAT EQUIPMENT IS REQUIRED TO MAKE THESE MEASUREMENTSl Fl)r all of these measurements you will need Ihe HP Model 5508A Measurement Display unh and the liP Model 5518A Laser Head, You will most lik ly also need an HP M od...
Model 5528A Introduction HARDWARE - GENERAL DESCRIPTIONS more etaile des ription, see Section Section Appendix A and Appendix · 5508A Measurement Display The 5508A Measurement Display unh provides the operator interface for the laser Measurement System. It also provides operating power for thc laser...
Page 29
Model 5528A Inlroduction Straightness Optics There arc two sets of ght ne Oplics av.ll1able to be chosen based on the range traveled by the machine The 10774A �hort Range Iralghtness Interferometer is d gned measurement) • over the range of 100 to 3000 rnm (4 to 120 inches) measurement�...
Page 31
Model 5528A First look SECTION 2 FIRST LOOK CONTENTS SAfETY PRECAUTIONS PURPOSE 5508A MEASUREMENT DISPLAY 5516A LASER HEAD 10751 AIR SENSOR AND 10757 MATERIAL TEMPERATURE SENSOR OPERATION PHYSICAL SETUP INTERCONNECTION AND TURN·QN ASSEMBLY OF OPTICS INSTALLATION AND ALIGNMENT OF OP TICS...
Page 32
Model 5528A First Look WARNING LASER RADIATION IS [MinED rROM THE APERTURE ON THE SS'8A LASER HEAD. DO NOT STARE INTO THE BEAM. THIS PRODUCT IS A CLASS II LASER PRODUCT CONroRMING TO FlDERAL BUREAU OF RADiOlOGICAL HEAUH REGU· LATIONS 21 CFR '0<0.'0 AND 1040.11,...
Page 34
RESET Releases Laser Measurement S ys m from l (if il operating HP-IIJ Wd§ under HP-IB control). Clear� error message, If one is being displayed. Kelurns Laser Me aSur t System to most-recently-chosen mcasurcm�rll mode. NOTE The RESET key cleOlI's only Ihl!' measurement data.
Model5S26A Firs! look Front Panel - Entry Keys The ENTRY keys illlow you to assign v<tJues certain parameters as t.lescrlbed above. No measurement informaTion is when entering numbers inlo the Me emen Display. 1051 Rear Panel The Measurement Display unil's rear panel is shown in Figure It is port...