Electrical Data - Danfoss VLT DriveMotor FCP 106 Operating Instructions Manual
Hide thumbs
Also See for VLT DriveMotor FCP 106:
- Programming manual (148 pages) ,
- Design manual (82 pages) ,
- Operating instructions manual (62 pages)
Table of Contents
Advertisement
Specifications
7.2 Electrical Data
Enclosure
PK55
1)
NO
HO
Overload
Typical shaft
0.55
output [kW]
Typical shaft
0.75
output [hp]
Max. cable cross-
section in
2
terminals
4/10
(mains, motor)
[mm
2
/AWG]
Output current
40 °C ambient temperature
Continuous
1.7
(3x380-440 V) [A]
Intermittent
1.9
2.7
(3x380-440 V) [A]
Continuous
1.6
(3x440-480 V) [A]
Intermittent
1.8
2.6
(3x440-480 V) [A]
Max. input current
Continuous
1.3
(3x380-440 V )[A]
Intermittent
1.4
2.0
(3x380-440 V) [A]
Continuous
1.2
(3x440-480 V) [A]
Intermittent
(3 x 440-480 V)
1.3
1.9
[A]
Max. mains fuses
Table 7.10 Mains Supply 3x380-480 V AC Normal and High Overload: MH1, MH2, and MH3 Enclosure
1) NO: Normal overload, 110% for 1 minute. HO: High overload, 160% for 1 minute
A frequency converter intended for HO requires a corresponding motor rating. For example, Table 7.10 shows that a 1.5 kW motor for HO requires
a P2K2 frequency converter.
2) Max. cable cross-section is the largest cable cross-section that can be attached to the terminals. Always observe national and local regulations.
MG03L202
Operating Instructions
MH1
PK75
P1K1
NO
HO
NO
HO
0.75
1.1
1.0
1.5
4/10
4/10
2.2
3.0
2.4
3.5
3.3
4.8
2.1
2.8
2.3
3.4
3.1
4.5
2.1
2.4
2.3
2.6
2.6
3.7
1.8
2.2
2.0
2.5
2.4
3.5
See chapter 7.10 Fuse and Circuit Breaker Specifications
Danfoss A/S © Rev. 06/2014 All rights reserved.
P1K5
P2K2
NO
HO
NO
HO
1.5
2.2
2.0
3.0
4/10
4/10
3.7
5.3
4.1
5.9
5.8
8.5
3.4
4.8
3.7
5.4
5.3
7.7
3.5
4.7
3.9
4.6
5.2
7.0
2.9
3.9
3.2
4.2
4.3
6.3
MH2
MH3
P3K0
P4K0
P5K5
NO
HO
NO
HO
3.0
4.0
4.0
5.0
4/10
4/10
7.2
9.0
7.9
11.5
9.9
14.4
6.3
8.2
6.9
10.1
9.0
13.2
6.3
8.3
6.9
9.6
9.1
12.0
5.3
6.8
5.8
8.4
7.5
11.0
7
7
37
Advertisement
Table of Contents
