DragonWave Horizon COMPACT Plus Product Manual page 87

Compact out-door-unit
Hide thumbs Also See for Horizon COMPACT Plus:
Table of Contents

Advertisement

set ecfm mep crosscheck start-delay {default}|{start-
delay<3-100>}
set ecfm mep level [<0-7> [delete] [inward] mpid
<id(1-8191)> [vlan<vlan-id(1-4094)>] [active]
set ecfm mep-capability level {<level-id(0-7)> | level-
list} [on|off] [vlan {<vlan-id(1-4094)> | vlan-
list}]([ping] [muliticast-ping] [one-way-frame-
delay] [multicast-test] [turnaround-delay][ais]
[rdi])
set ecfm mip ccm-database caching {enable | disable}
set ecfm mip ccm-database hold-time [<hours>(24-
48)]
set ecfm mip ccm-database size [<entries(1000-
10000)>]
set ecfm mip dynamic evaluation {enable|disable}
set ecfm mip level [delete] <level-id(0-7)> vlan <vlan-
id(1-4094)> [active]
set ecfm mip-creation-criteria {none | default | explicit}
set ecfm oui {<aa:aa:aa> | default}
set ecfm port port<1-1> {on|off}
set ecfm service <{[config] <service_name> [{icc
<icc_code> umc <umc_code>] [vlan <vlan-id(1-
4094)>] [mip-creation-criteria {none | default |
explicit | defer}] [sender-id-permission {none |
chassis | manage | chassis-mgt-address |
defer}]}>| <{delete <service_name>
set ecfm traceroute cache [ on|off | { holdtime { default
| <integer(1-65535)} }
set ecfm y1731 [on | off ]
set enet config
set enet speed alarm enable port1 | port2 on|off
set eoam [on | off]
set eoam dwi-msg mode [eoam | bypass-eoam]
set eoam fault-management [on | off | start]
set eoam link-monitor event-resend [count(1-10)]
set eoam oui [<aa:aa:aa> | default]
set haam[on/off]
set haam eoam option
set haam manual mode[on|off]
set haam wtr[duration]
set http secure access [Admin|Noc|Super] [on/off]
set ip address [aaa.bbb.ccc.ddd]
set ip config
set lo nulling [on/off]
set logging [on/off]
set network loopback [nearend | farend | off] mac-
address <queue N> <timeout>
set network management interface
set network protocol strict [on/off]
set noc user
set optical transmitter state [on/off]
set pause state [on/off]
set peer authentication failure [action]
set peer authentication group key [key]
set peer authentication type [authentication
type]
set peer authentication unique key [key]
set performance log interval [hr:min:sec]
set performance logging
set port eoam [port <1-2>] [on | off]
Horizon Compact Plus Release 1.0.1
[p1–p4 or dp1–dp4]
Appendix A – CLI Command List
set port eoam fault indication [port <1-2>] [critical-
event | dying-gasp] [on | off]
set port eoam fault-management action [port <1-2>]
[critical-event | dying-gasp | link-fault] [none |
warning]
set port eoam fault-management link-monitor action
[port <1-2>] [frame | frame-period | frame-sec-
summary] [none | warning]
set port eoam fault-management mib-request [port
<1-2>] <branchleaf:branchleaf:...>
set port eoam fault-management mib-variable count
[port <1-2>] <count(1-100)>
set port eoam fault-management remote-loopback
[port <1-2>] [test] [count <no of packets(1-
1000)>] [packet <size(64-1500)>] [pattern
<hex_string(8)>] [wait-time <integer(1-10)>]
set port eoam link-monitor [port <1-2>] [frame |
frame-period | frame-sec-summary] [on | off]
set port eoam link-monitor default [port <1-2>] [frame |
frame-period | frame-sec-summary] [threshold
| window]
set port eoam link-monitor frame-sec-summary
threshold [port <1-2>] [<count(0-900)>]
set port eoam link-monitor frame-sec-summary
window [port <1-2>] [<size(100 - 9000)>]
set port eoam link-monitor threshold [port <1-2>]
[frame |frame-period] [<count(1234..)>]
set port eoam link-monitor window [port <1-2>]
[frame <size(10 - 600)> | frame-period
<size(1100000 - 89000000)> ]
set port eoam mode [port <1-2>] [active | passive]
set port eoam remote-loopback [port <1-2>] [on | off |
deny | permit]
set programmed frequency [IndexID]
set qos [on/off]
set qos policy [strict priority / wfq]
set queue utilization threshold [qid] [depth] [time]
set radio band [radioBandName]
set radio config
set radio loopback [on | off] <timeout> <network>
set radio transmitter state [on | off] [mute time
(seconds)]
set radius server host [index] [server addr]
set radius server key [index] [key]
set radius super user authentication [On|Off]
set redundancy link monitor parameters
set redundancy link switch parameters
set redundancy mode
set redundancy override [primary | secondary |
manual | auto ]
set redundancy standby enet state
set redundancy state switch
set rls [on/off] | [basic|advanced]
set rls link control [on/off]
set rls link enable [on/off]
set rls link monitor parameters [mk erred blks] [brk
erred blks] [mk samples] [brk samples] [mk
sample time] [brk sample time] [brk sample rst
time]
set rls make rsl [make rsl threshold] [rsl mk sample
time sec]
set rls port groups
Wireless Ethernet Product User Manual – Volume 1
77

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Horizon COMPACT Plus and is the answer not in the manual?

Related Products for DragonWave Horizon COMPACT Plus

Table of Contents