Table of Contents
Advertisement
GPRS Receiver 1 Options
[201] GPRS Receiver 1 Account Code
Default (0000000000)
The account code is used by the central station to distinguish between transmitters. This account code is used
when transmitting heartbeat signals to the central station receiver. Signals received from the control panel will use
the control panel account number. Valid range: 0000000001 - FFFFFFFFFE.
Programming this Section as all 0 or all F will cause a Module Configuration Trouble (yellow LED = 12 flashes).
[202] GPRS Receiver 1 DNIS
Default (000000)
The DNIS is used in addition to the account code to identify the Communicator module at the central station. Valid
range: 000000 - 099999. Values are entered as leading 0 followed by the five digit DNIS. Format is BCD.
NOTE: Each Ethernet/GPRS receiver must be programmed with a unique DNIS.
[203] GPRS Receiver 1 Address
Default (000.000.000.000)
Enter the GPRS Receiver 1 IP address. This information will be provided by your central station system administra-
tor. Each 3 digit segment of the address must be within a valid range of 000-255.
NOTE: When a valid IP address has been entered, the GPRS is enabled and will communicate events
over the GPRS channel.
[204] GPRS Receiver 1 Port
Default (0BF5/3061)
This Section determines the port used by GPRS Receiver 1. Change the default value of this port when your instal-
lation is located behind a firewall, and must be assigned a particular port number as determined by your central sta-
tion system administrator. Valid range: 0000 - FFFF.
NOTE: Programming this Section with 0000 will disable the receiver.
[205] GPRS Receiver 1 APN
Default ( )
The Access Point Name (APN) determines the GPRS network that the Communicator will connect to. This informa-
tion is available from your network carrier. Program this Section as 32 ASCII characters.
NOTE: When a SIM card with a custom APN is used, the unit will not have access to the internet. DLS
and remote flash can still be done if Section [221] is programmed with a valid Public APN.
[206] GPRS Receiver 1 Domain Name
Default ( )
Programming this Section is not permitted on a UL/ULC listed system.
Enter the Domain Name as 32 ASCII characters. This information will be provided by your central station system
administrator.
GPRS Receiver 2 Options
[211] GPRS Receiver 2 Account Code
Default (0000000000)
The account code is used by the central station to distinguish between different transmitters. This account code is
used when transmitting signals to the central station receiver. Signals received on the control panel will use the
control panel account number. Valid range: 0000000001 - FFFFFFFFFE.
NOTE: Programming this Section as all 0 or F will cause a Module Configuration Trouble (yellow LED = 12 flashes).
[212] GPRS Receiver 2 DNIS
Default (000000)
The DNIS is used in addition to the Account Code to identify the Communicator module at the central station. Valid
range: 000000 - 099999. Values are entered as a 0 followed by the 5 digit DNIS value. Format is BCD.
NOTE: Each Ethernet/GPRS receiver must be programmed with a unique DNIS.
[213] GPRS Receiver 2 Address
Default (000.000.000.000)
Enter the GPRS Receiver 2 IP address. This IP address will be provided by your central station. Format is 4 fields,
each field is 3 digit decimal. Valid range: 000 - 255.
NOTE: When a valid address has been entered, GPRS Receiver 2 is enabled and will communicate
events over the GPRS path.
[214] GPRS Receiver 2 Port
Default (0BF5/3061)
This Section defines the port of GPRS Receiver 2. Change the value of this port when your installation is located
behind a firewall, and must be assigned a particular port number, as determined by your central station system
administrator. Valid range: 0000 - FFFF.
NOTE: Do not program GPRS Receiver 1 and GPRS Receiver 2 to communicate to the same receiver.
[215] GPRS Receiver 2 APN
Default ( )
The APN determines the GPRS network that the Communicator will connect to. This information is available from
your network carrier. Program this Section with up to 32 ASCII characters.
NOTE: When a SIM card with a custom APN is used, the unit will not have access to the internet. DLS
and remote flash can still be done if Section [221] is programmed with a valid Public APN.
[216] GPRS Receiver 2 Domain Name
Default ( )
Programming this Section is not permitted on a UL/ULC listed system.
Enter the GPRS Receiver 2 Domain Name with up to 32 ASCII characters.
21
Advertisement
Table of Contents
