Table of Contents
Advertisement
OFF: GPRS Receiver 1 will not be supervised. When disabled, heartbeat is not sent to the receiver.
NOTE: GPRS Receiver 2 can not be supervised.
[3] Supervision Type
Default (OFF)
ON: Heartbeat 1 (Commercial Supervision). This supervision type is suitable for applications where swap detec-
tion is required on the supervisory packet.
OFF: Heartbeat 2 (Residential Supervision). This supervision type is suitable for applications where supervision
of the communication path to the receiver is required. (no swap detection).
NOTE: Commercial supervision is more data intensive than residential supervision and should only be
used when required to meet the approval for the installation.
[4] GSM Primary
Default (OFF - TL260-SM/TL260GS-SM) (ON - GS2060-SM)
ON: GPRS channel is the primary path. Ethernet channel is the secondary path, if it exists.
OFF: Ethernet channel is the primary path in a dual Communicator. GPRS channel is the secondary path.
[5] Redundant Communications
Default (OFF) (TL260GS-SM only)
ON: Events will be communicated to Ethernet Receiver 1 and GPRS Receiver 1 at the same time. Events will be
communicated to Ethernet Receiver 2 and GPRS Receiver 2 at the same time. As long as the event is successfully
communicated to 1 of the 2 paths (Ethernet or GPRS) the Communicator will move on to the next event.
NOTE: Do not configure Ethernet Receiver 1 and GPRS Receiver 1 to communicate using a common
receiver configuration (i.e., identical Receiver IP address and Receiver Remote Port).
OFF: Events will be communicated to the receivers individually.
NOTE: Toggle should be OFF when guaranteed message delivery to both receivers is required.
[6] Remote Firmware Upgrade
Default (ON)
ON: The Communicator module firmware can be remotely upgraded using the Ethernet/GPRS paths.
OFF: The Communicator module firmware can not be remotely upgraded. Local firmware upgrade is still possible.
[7] Alternate Test Transmissions Default (OFF).
ON: When the periodic test transmission interval occurs, the test transmission will alternate between being sent
to the primary and secondary receivers with each test transmission interval.
OFF: When the periodic test transmission interval occurs, the test transmission will be sent to the programmed
receivers, based on the settings of the periodic test transmission reporting codes.
[8] GSM Low Signal Trouble. Default (OFF).
[006] System Toggle Options 2
[1] Ethernet 1 Receiver Enabled. Default (ON) (OFF for GS2060-SM).
ON: Ethernet Receiver 1 is enabled.
OFF: Ethernet Receiver 1 is disabled.
[2] Ethernet 2 Receiver Enabled. Default (ON) (OFF for GS2060-SM).
ON: Ethernet Receiver 2 is enabled.
OFF: Ethernet Receiver 2 is disabled.
[3] Reserved. (OFF).
[4] GPRS 1 Receiver Enabled. Default
ON: GPRS Receiver 1 is enabled.
OFF: GPRS Receiver 1 is disabled.
[5] GPRS 2 Receiver Enabled. Default
ON: GPRS Receiver 2 is enabled.
OFF: GPRS Receiver 2 is disabled.
[6] Reserved (OFF).
[7] DLS Over GPRS. Default (ON).
NOTE: Program this toggle as OFF if you want to completely disable DLS from using the GPRS path.
ON: DLS is enabled on the GPRS path.
OFF: DLS is disabled on the GPRS path.
NOTE: If this Toggle is OFF, DLS sessions will occur on the Ethernet path only, regardless of Primary
Path set in Section [005] Toggle Option [4]. If it is ON then the Communicator will connect to the Primary
path first for DLS and if the session fails, the Secondary path will be used.
[8] Interactive over GPRS. Default (ON).
[007] DNS Server IP 1
Default (000.000.000.000)
Programming this Section is not permitted on a UL/ULC listed system.
Enter the IP address for DNS Server 1. Format is 4 fields, each field is a 3 digit decimal. Valid range: 000-255.
NOTE: If no value is programmed and DHCP is used, the DHCP Server will configure the address. If an
address is programmed and DHCP is used, the address that you program will be used instead of the
DHCP address.
(ON).
(ON).
15
Advertisement
Table of Contents
