Communicator Programming Sections; System Options - DSC GS2060-SM Installation Manual

Alarm communicator, gprs cellular communicator, ethernet/internet communicator, ethernet/internet and gprs dual-path communicator

Hide thumbs

Table Of Contents

Table of Contents

The Programming Sections in this document are accessed via panel Section for Ethernet/GPRS Programming.

Enter: [*][8][installer code][851][# ##], Where # ## is the 3 digit Section number referenced in this document.

The Programming Worksheets at the end of this document can be used to record the new values when pro-

gramming changes have been made from the default values. Default values are provided for each Section.

Programming Sections cannot be modified from the keypad. Installers may review/record programming Options

at the keypad.

NOTE: Ethernet/GPRS Programming Sections accessed through the keypad are for display purposes

only. Configuration changes must be done remotely. Specified panel Sections must be configured for

proper operation of the Communicator and the Panel.

System Options

[001] Ethernet IP Address

Default (000.000.000.000)

Enter the IP address of the Communicator. Ensure that the IP address is unique to your Communicator on the local

network. Format is 4 fields, each field is a 3 digit decimal number. Valid range: 000-255. If an IP address is pro-

grammed in this Section, the unit will operate with Static IP (DHCP disabled). Sections [002] and [003] must also be

programmed when using Static IP addresses.

NOTE: Default for this Section is Dynamic Host Configuration Protocol (DHCP) enabled. When enabled,

the DHCP Server will set values for: IP Address [001], Subnet Mask [002], and Gateway [003]. Program-

ming an IP address in this Section will disable DHCP (Static IP).

[002] Ethernet IP Subnet Mask

Default (255.255.255.000)

Enter the Ethernet IP Subnet Mask of the dual Communicator. Format is 4 fields, each field is a 3 digit decimal

number. Valid range: 000-255.

NOTE: If DHCP is enabled, the DHCP Server will assign the subnet mask for this Section and the

programmed value will be ignored.

[003] Ethernet Gateway IP Address

Default (000.000.000.000)

Enter the Ethernet Gateway IP address of the Communicator. The gateway IP address is required when a router is

used on the local network to reach the destination IP address specified in Section [001]. Format is 4 fields, each

field is a 3 digit decimal number. Valid range: 000-255.

NOTE: If DHCP is enabled, the DHCP Server will assign the Gateway IP address for this Section and the

programmed value will be ignored.

[004] Receiver Supervision Interval

Default (0087/135)

When receiver supervision is enabled (ON) in Section [005] Toggle Option [3], the unit sends heartbeats to Ethernet

Receiver 1 or GPRS Receiver 1 to test the communications path. Use this Section to set the interval time (in sec-

onds) when heartbeats will be sent. Valid range 000A-FFFF seconds. If the programmed value is less than

(000A/10) seconds, supervision is disabled.

Jurisdiction

UL Commercial Burglary

UL Residential Fire

UL Residential Burglary

ULC Commercial Burglary Active

ULC Commercial Burglary Passive

ULC Commercial Fire Active

ULC Commercial Fire Passive

•

Receiver Window: This is the supervision timeout that must be configured at the central station receiver.

•

Recommended Values: This is the recommended heartbeat interval that should be programmed into the

Communicator.

•

For ULC passive systems (not using heartbeat supervision), the Daily test transmission must be enabled

over each available communication channel Sections [125] and [225]. When programming with Connect24,

the recommended intervals will be programmed automatically when the required window is selected.

[005] System Toggle Options

[1] Ethernet Receiver 1 Supervised

Default (OFF) (TL260-SM/TL260GS-SM only).

ON: Ethernet Receiver 1 will be supervised and heartbeats will be sent to Ethernet Receiver 1 based on the

supervision interval programmed in Section [004].

OFF: Ethernet Receiver 1 will not be supervised. When disabled, heartbeat 1 is sent to the Ethernet receiver

once every hour, regardless of supervision type (heartbeat 1 or 2). The heartbeat is resent every 5 seconds until

ACK. If no event or heartbeat ACK is received after (Receiver Supervision Interval + 75 seconds), Supervisory

trouble is indicated.

NOTE: Ethernet Receiver 2 can not be supervised.

[2] GPRS Receiver 1 Supervised

Default (OFF)

ON: GPRS Receiver 1 will be supervised and heartbeats will be sent to GPRS Receiver 1 based on the super-

vision interval programmed in Section [004]. If ACK to heartbeat is not received, it is retransmitted every 5 sec-

onds. Failure to ACK 2 consecutive heartbeats will reset the radio.