Internet and lte/hspa dual-path alarm communicator
lte/hspa alarm communicator
hspa cellular alarm communicator
internet and hspa dual-path alarm communicator
internet alarm communicator (45 pages)
The device is a backup wireless communicator that sends alarm system information to a System III or System II receiver through a GSM/ GPRS wireless network. The device is available in two models that are different for the operating frequency only: GS3055-IG = 850/1900 MHz GS3055-IGW = 900/1800 MHz.
Description This Device manages SMS and Central Station transmissions and can simulate the land line in the event of trouble (land line down) or even substitute the land line completely in areas where the GSM service is provided and where the land line is not available. This Device has capability of communicating alarm signals via the GPRS data network.
CONNECTING THE DEVICE This section describes the various terminals. Fig. 2 shows a typical wiring diagram. - - (1) Earth Ground: This terminal must be connected to the Mains Earth, in order to comply with the Telecommunications Network Safety Standards (Overvoltage Protection Requirements). LE (2-3) External telephone line: These terminals can be connected to the land line.
OPERATING PRINCIPLES Simulated Land Line The Simulated land line provides the alarm control panel (with dialer interface) with a backup line in the event of PSTN line trouble. If the voltage on the land line terminals (LE) drops below 3 V for a period of between 10 to 45 seconds (depending on the device connected to the LI terminals), this Device will switch the connected telephone device to the GSM Network for a full 15 minute interval, at the end of this interval, it will check the land line: —...
Function Priority Simulated Land Line Priority If the equipment connected to the LI terminals (e.g. Control panel) tries to engage the line, this Device will interrupt any ongoing communications (SMS or ContactID) in order to send the calls generated by the device. This Device will restart the interrupted communications when the equipment disengages the line.
Monostable Outputs (for appliance management) Monostable OC outputs can be activated in 2 ways. 1. By sending a case sensitive SMS text message containing the respective Access Code placed between pound (#) signs and Output Label followed by “=ON” or “=OFF”, as follows: #ACCESSCODE#OUTPUTLABEL=ON #ACCESSCODE#OUTPUTLABEL=OFF 2.
Telephone Page The Telephone Page phonebook holds 95 telephone numbers. , , , , , The first eight numbers in the phonebook will also be used for the SMS functions. Telephone Numbers z Description: enter an alphanumeric string of up to 20 characters. z Number: enter a telephone number of up to 20 digits (only digits and “+”...
Priority This section will allow you to select the operating priority of this Device: Interface (at default) or SMS Dialer/Contact ID Communicator. Pay-as-you-go Balance message , , , , , NOTE: The Manufacturer shall not assume responsibility for Pay-as-you-go credit services managed by GSM Network Providers.
Contact ID Page This page will allow you to set up the Contact ID function. Telephone numbers to call Four telephone numbers of up to 20 digits (digits and + signs). This Device will try each telephone number 3 times before considering a call unsuccessful and quitting. , , , , , The Contact ID Codes will be sent to the first number (with Contact ID reporting protocol) that answers the call.
GPRS page This page outlines the GPRS configuration options. Access Point Name (APN) Enter the Access Point Name of the GPRS service provider being used. (example: ibox.tim.it) Please contact the GPRS service provider for this information. Receiver IP address and Port Enter the primary (mandatory) and back-up (optional) receiver IP addresses and port numbers.
Status Page This page will allow you to monitor and control in real-time all the Device functions and, if not previously done, unblock the SIM CARD PIN. , , , , , ATTENTION: This page is updated every 5 seconds. Status section This section shows the GSM Module data.
Este equipo es un comunicador de respaldo que envía información de sistemas de alarma a receptoras System III o System II vía red GSM/GPRS. El equipo está disponible en dos versiones diferenciadas sólo por la frecuencia de trabajo: GS3055-IG = 850/1900 MHz GS3055-IGW = 900/1800 MHz.
Descripción Este equipo trabaja con SMS y transmisiones a central receptora y puede simular la línea de teléfono en caso de fallo de la línea terrestre o sustituir a esta completamente donde exista cobertura GSM y no sea posible dispone de línea terrestre. También tiene la capacidad de comunicar alarmas vía red de datos GPRS.
CONEXIÓN DEL EQUIPO Esta sección describe los diferentes terminales. La Fig.2 muestra un diagrama típico. - - (1) Toma de Tierra - Este Terminal debe ser conectado a una toma de tierra para cumplir con los estándares de seguridad de redes de telecomunicaciones.
PRINCIPIOS DE OPERACIÓN Línea Telefónica Simulada La simulación de línea telefónica proporciona al panel de alarmas un respaldo de línea en caso de fallo de línea terrestre. Si la tensión de línea telefónica en los terminales LE baja de 3V por un período entre 10 y 45 segundos, el equipo conmutará a la red GSM durante un intervalo de 15 minutos, al final del cual chequeará...
Función Prioridad Prioridad a Simulación de Línea Terrestre Si los aparatos conectados a los terminales LI (p.ej. panel de alarmas) intentan capturar la línea, el equipo interrumpirá cualquier comunicación en curso (SMS o CID) para permitir las comunicaciones de ese aparato. El equipo restablecerá las comunicaciones pendientes cuando le sea devuelta la línea.
Salidas Monostables (aplicación del usuario) Las salidas monostables pueden ser activadas de 2 maneras. 1. Enviando un mensaje SMS sensible a mayúsculas con el correspondiente Código de Acceso, entre almohadillas y el Nombre de la Salida seguido de =ON o =OFF, tal que así: #Código_de_Acceso#Nombre_de_la_Salida=ON #Código_de_Acceso#Nombre_de_la_Salida=OFF 2.
Teléfonos La página de Agenda telefónica contiene hasta 95 números de teléfono. , , , , , Los primeros ocho números podrás se usados también para funciones SMS. Números de Teléfono z Descripciones - Entre una cadena alfanumérica de hasta 20 caracteres. z Número - Entre el número de teléfono de hasta 20 dígitos (sólo se aceptan números y el signo +).
Prioridad Esta sección le permitirá configurar la prioridad de servicios del equipo: Interface o Avisador. Mensaje de aviso de Fin de Saldo , , , , , NOTA - El fabricante no asume la responsabilidad de los servicios de crédito prepago gestionados por los proveedores de la red GSM.
Contact ID Esta página permite configurar la función de comunicación por Contact ID. Teléfonos de Receptora Puede programar 4 números de teléfono de hasta 20 dígitos. El equipo intentará llamar 3 veces a cada teléfono antes de considerar una llamada fallida. , , , , , Los eventos en Contact ID se enviarán al primer número que responda la llamada satisfactoriamente.
GPRS Esta página describe las opciones de configuración GPRS. Nombre del Punto de Acceso (APN) Introduzca el Nombre de Punto de Acceso a la red GPRS que esté usando su proveedor. Contacte con su proveedor para más información. Puerto y Dirección IP de Receptora Introduzca la dirección IP primaria (obligatoria) y secundaria (opcional) y los números de Puerto.
Estado Esta sección le permitirá monitorizar y controlar en tiempo real todas las funciones del equipo y, si no lo hizo antes, desbloquear el PIN de la tarjeta SIM. , , , , , ATENCIÓN: Esta página se actualiza cada 5 segundos Sección Estado Esta sección le muestra los datos del módulo GSM.
INFORMACIÓN PARA EL USUARIO Llamadas por red GSM Si conecta este equipo a un teléfono es posible realizar llamadas de voz bajo la red GSM. Información avanzada Refiérase a las siguientes secciones para obtener información avanzada del equipo: LED’S DE ESTADO ...
Page 31
The above mentioned GS3055-IG and GS3055-IGW had been designed and made to the highest standards of quality and performance.The manufacturer recommends that the installed system should be completely tested at least once a month. DSC shall not be responsible for damage arising from improper installation or maintenance by unauthorized personnel.
Page 32
DIGITAL SECURITY CONTROLS TORONTO - CANADA http://www.dsc.com ISTISD23GS3055I 4.0 191007 P70...