Diagnostic Code Generation Conditions And Inspection Items; E-01: Accel Pedal Sensor 1 (Warning Lamp Flashes: 24) P0122; E-01: Accel Pedal Sensor 1 (Warning Lamp Flashes: 24) P0123; E-02: Accel Pedal Sensor 2 (Warning Lamp Flashes: 16) P0222 - Mitsubishi 6M60-TL Service Manual

3.2 Diagnostic code generation conditions and inspection items

E-01: Accel Pedal Sensor 1 (warning lamp flashes: 24) P0122
Generation condition
Recoverability
Control effected by electronic control unit
Service data
Inspection
Electronic control unit connector
Electrical equipment
E-01: Accel Pedal Sensor 1 (warning lamp flashes: 24) P0123
Generation condition
Recoverability
Control effected by electronic control unit
Service data
Inspection
Electronic control unit connector
Electrical equipment
E-02: Accel Pedal Sensor 2 (warning lamp flashes: 16) P0222
Generation condition
Recoverability
Control effected by electronic control unit
Service data
Inspection
Electronic control unit connector
Electrical equipment
E-02: Accel Pedal Sensor 2 (warning lamp flashes: 16) P0223
Generation condition
Recoverability
Control effected by electronic control unit
Service data
Inspection
Electronic control unit connector
Electrical equipment
Accelerator pedal position sensor 1 voltage is below standard value.
System recovers if signal becomes normal with starter switch in ON position.
• Control is effected using accelerator pedal position sensor 2.
• If both sensors 1 and 2 are faulty, control is effected on assumption that accel-
erator pedal is depressed 30% when accelerator switch is on and the pedal is
not depressed when the switch is off.
22: Accel Pedal Position (unfiltered), 23: Accel Pedal Position (filtered),
24: Accel Pedal Sensor Voltage 1
03 : Accelerator pedal position sensor
#324: Accelerator pedal position sensor
Accelerator pedal position sensor 1 voltage is above standard value.
System recovers if signal becomes normal with starter switch in ON position.
• Control is effected using accelerator pedal position sensor 2.
• If both sensors 1 and 2 are faulty, control is effected on assumption that accel-
erator pedal is depressed 30% when accelerator switch is on and the pedal is
not depressed when the switch is off.
22: Accel Pedal Position (unfiltered), 23: Accel Pedal Position (filtered),
24: Accel Pedal Sensor Voltage 1
03 : Accelerator pedal position sensor
#324: Accelerator pedal position sensor
Accelerator pedal position sensor 2 voltage is below standard value.
System recovers if signal becomes normal with starter switch in ON position.
• Control is effected using accelerator pedal position sensor 1.
• If both sensors 1 and 2 are faulty, control is effected on assumption that accel-
erator pedal is depressed 30% when accelerator switch is on and the pedal is
not depressed when the switch is off.
22: Accel Pedal Position (unfiltered), 23: Accel Pedal Position (filtered),
25: Accel Pedal Sensor Voltage 2
03 : Accelerator pedal position sensor
#324: Accelerator pedal position sensor
Accelerator pedal position sensor 2 voltage is above standard value.
System recovers if signal becomes normal with starter switch in ON position.
• Control is effected using accelerator pedal position sensor 1.
• If both sensors 1 and 2 are faulty, control is effected on assumption that accel-
erator pedal is depressed 30% when accelerator switch is on and the pedal is
not depressed when the switch is off.
22: Accel Pedal Position (unfiltered), 23: Accel Pedal Position (filtered),
25: Accel Pedal Sensor Voltage 2
03 : Accelerator pedal position sensor
#324: Accelerator pedal position sensor
13E
13E-23