How To View Read Status Of Devices, Zones, And System Settings; Overview; How To Display The Total Of Installed Devices; How To Display A Point Or Zone For Read Status - Notifier AFC-600 Operating Manual

How to View and Print Read Status Information
2YHUYLHZ
+RZ WR 'LVSOD\ WKH 7RWDO
RI ,QVWDOOHG 'HYLFHV
&D
+RZ WR 'LVSOD\ D 3RLQW
RU =RQH IRU 5HDG 6WDWXV
&
&
AFC-600 Operations PN 51033:A 3/8/99
Technical Manuals Online! - http://www.tech-man.com
+RZWR9LHZ5HDG6WDWXVRI'HYLFHV=RQHVDQG6\VWHP6HWWLQJV
Read Point options 0, 2, and 4 in the Read Status Screen let you display and view
information for devices and zones programmed into the control panel, as well as view
system and annunciator settings. This section provides instructions and sample displays
so you can view Read Status. Table 11 shows the topics covered in this section.
To view Read Status for
Intelligent Detectors
Control/relay and Monitor
modules
NAC and Panel Circuits
Software Zones (Z01-Z99)
Special Zones (F0-F9)
Releasing Zones (R0-R9)
System Functions
Annunciator Selections
To view the total number of installed devices, enter the Read Status screen by pressing
the key, then 2. By pressing A, a screen similar to the following will appear:
ENTER
/  'HWV  0RGV / 'HWV 0RGV
3DQHO 2XWSXWV 
)LJXUH  'LVSOD\ ,QVWDOOHG 'HYLFH 1XPEHUV 6FUHHQ
From the Read Status screen, press 0, then press the
Point Entry screen (Figure 33). Figure 33 also contains instructions for displaying a
detector, zone, NAC, Panel Circuit, monitor module, or control module. When you
select a device or a zone, the control panel displays information for the device or
zone—but does not send this information to the serial ports or the History buffer.
]
7R YLHZ D ]RQH SUHVV
]RQH QXPEHU 
(17(5
=21( =$$(
02'8/( /0$$$(
7R YLHZ D PRQLWRU RU FRQWUROUHOD\
,
PRGXOH SUHVV  6/&
QXPEHU PRGXOH 6/& DGGUHVV

(17(5
)LJXUH  5HDG 3RLQW (QWU\ 6FUHHQ
Refer to
"How to View Read Status for a Detector" on page 40
"How to View Read Status for a Control/Relay or
Monitor Module" on page 41
"How to View Read Status for a NAC or Panel Circuit"
on page 42
"How to View Read Status for a Software Zone
(Z01-Z99)" on page 43
"How to View Read Status for a Special Zone (F0-F9)"
on page 43
"How to View Read Status for a Releasing Zone
(R0-R9)" on page 43
"How to Read Status for System Functions" on page 44
"How to Read Status for Annunciator Selections" on
page 45
7DEOH  5HDG 3RLQW 7RSLFV
%HOOV 
ENTER

'(7(&725 /'$$$(
287387 &.7 $$(
7R YLHZ D 3DQHO &LUFXLW RU DQ 1$&
SUHVV
H[DPSOH  IRU %  IRU 3DQHO
&LUFXLW  HWF 
 5HDG 6WDWXV 2SHUDWLRQ
key to display the Read
+
7R YLHZ D GHWHFWRU SUHVV 
6/& QXPEHU GHWHFWRU 6/& DGGUHVV

(17(5
-
 WZRGLJLW DGGUHVV IRU

(17(5
39