How To Select Amg Group Functions; How To Select Factory-Programmed Messages (Vrom); How To Record Custom Messages (Vram Option) - Notifier AFC-600 Operating Manual

 9RLFH $ODUP 6\VWHPV
+RZ WR 6HOHFW
)DFWRU\3URJUDPPHG
0HVVDJHV 9520
1RWH
,I D GLJLWDOO\VWRUHG YRLFH
PHVVDJH IDLOV WKH $0*
DXWRPDWLFDOO\ VZLWFKHV WR WKH
GHIDXOW WRQH DQG JHQHUDWHV D
WURXEOH VLJQDO 5HIHU WR
'RFXPHQW   IRU D
FRPSOHWH GHVFULSWLRQ RI DOO
9520 6HULHV PHVVDJHV
+RZ WR 5HFRUG &XVWRP
0HVVDJHV 95$0
RSWLRQ
1RWH
$ 95$0 PHVVDJH FDQ EH
XS WR  VHFRQGV ORQJ 
95$0$ (QDEOH
LI LQVWDOOHG
95$0% (QDEOH
LI LQVWDOOHG
$0* ',3 6ZLWFK
ORDGLQJ FXVWRP PHVVDJHV
56
Technical Manuals Online! - http://www.tech-man.com
+RZWR6HOHFW$0**URXS)XQFWLRQV
Operation of tones and messages available in a voice alarm application depends on the
following:
• The type and number of VROM chips installed
• The audio tones or messages selected by AMG-1 DIP switch SW2 settings
Installing one or two optional VROMs lets you select a factory-programmed message
by setting DIP switches 6, 7, and 8 on the AMG-1. (Refer to "How to Select AMG-1
Tones and Voice Messages" on page 57.) For example, Figure 62 shows the text of
factory-recorded VROM-101 message in a male voice:
´0$< , +$9( <285 $77(17,21 3/($6( 0$< , +$9( <285 $77(17,21 3/($6( 7+(5( +$6
%((1 $ ),5( 5(3257(' 21 <285 )/225 7+(5( +$6 %((1 $ ),5( 5(3257(' 21 <285
)/225 3/($6( 352&((' 72 7+( 67$,5:$<6 $1' (;,7 7+( %8,/',1* '2 127 86( 7+(
(/(9$7256µ
You can record custom messages through the AMG-1 microphone or load a message
recorded on an audio cassette recorder. To do so, you must install at least one VRAM
chip in U14 (VRAM-A) or U15 (VRAM-B) on the AMG-1 (Figure 63). For example, if
the AMG-1 contains a VRAM chip in U14, record a message as follows:
1. If loading a message from a tape recorder, connect the tape recorder to J1 on the
AMG-1 (Figure 63).
2. Set the VRAM Enable DIP switch 4 (VRAM-A) on the AMG DIP Switch (SW2)
to the ON position. The AMG-1 starts to record input to VRAM-A from a tape
recorder or from the AMG-1 microphone.
3. Record a message through the AMG-1 microphone or load a message from a tape
recorder connected to J1.
4. When finished recording or loading the message, set the VRAM Enable switch to
the OFF position.
5. Recording on the VRAM chip starts when you press the microphone switch and
stops when you release the microphone switch.
Figure 63 shows the location of connector, VRAM, and VROM on the AMG-1:
$0* ',3
6ZLWFK 6:
6: IRU
2SWLRQDO 9RLFH 0HVVDJH 
)DFWRU\SURJUDPPHG 9520$
2SWLRQDO 9RLFH 0HVVDJH 
)DFWRU\SURJUDPPHG 9520%
AMG-1 and AMG-E Audio Message Generator
)LJXUH  6DPSOH 9520 0HVVDJH
)LJXUH  $0* &LUFXLW %RDUG
&RQQHFWRU - IRU WDSH
UHFRUGHU LQSXW FDEOH
0LFURSKRQH
FRQQHFWRU
2SWLRQDO 9RLFH 0HVVDJH 
8VHUSURJUDPPHG 95$0%
2SWLRQDO 9RLFH 0HVVDJH 
8VHUSURJUDPPHG 95$0$
AFC-600 Operations PN 51033:A 3/8/99