How To View Read Status For A Detector - Notifier AFC-600 Operating Manual

 5HDG 6WDWXV 2SHUDWLRQ
+RZ WR 9LHZ 5HDG 6WDWXV
IRU D 'HWHFWRU
&
&+
6/& QXPEHU
IROORZHG E\ WKUHH GLJLW
&
DGGUHVV
/
QH[W GHYLFH
0
SUHYLRXV GHYLFH
)
WR H[LW
1RWH 5HIHU WR ´'HWHFWRU
6HQVLWLYLW\ 6HWWLQJVµ LQ WKH $)&
 3URJUDPPLQJ 0DQXDO IRU
PRUH LQIRUPDWLRQ RQ WKH
3UH$ODUP DQG $ODUP 6HQVLWLYLW\
VHWWLQJV
40
Technical Manuals Online! - http://www.tech-man.com
From the Read Status screen, press 0, then press the
Read Status for a detector as follows: press
by the three digit address, then press the
detector D203: press
DETECTOR
key. The control panel displays information about the detector as shown in Figure 34:
'HYLFH VWDWXV
1250$/ 602.( ,21 '(7(&725 $''5 '
= =) = = =
'HIDXOW ]RQH
VHOHFWLRQ
)RXU ]RQH VHOHFWLRQV
IRU &%( OLVW
&XUUHQW DODUP UHDGLQJ
SHUFHQW RI DODUP
$ODUP VHQVLWLYLW\ OHYHO
3UH$ODUP VHQVLWLYLW\ /HYHO
)LJXUH  6DPSOH 'HWHFWRU 5HDG 6WDWXV 'LVSOD\
The following notes contain descriptions of the fields shown in Figure 34:
• Device Status The status of the detector: Normal, Alarm, or Test.
• Type Code The software Type Code that identifies the type of detector. (Refer to
"Point Programming" in AFC-600 Programming Manual.)
• Default Zone Selection Zone 01 (Heat detectors) Zone 02 (Ion detectors) Zone 03
(Photo detectors) Zone 04 (Laser detectors) Zone 05 (Multisensor).
• CBE list Four additional zones that along with the default zone make up the CBE
list for the device.
• Current alarm reading (xxx%) The current alarm reading of the detector, as a
percentage of the alarm sensitivity setting.
• Alarm sensitivity level (Ax) The alarm sensitivity (x=1-9) entered in the Detector
Sensitivity Screen.
• Pre-Alarm sensitivity level (PA:x) The Pre-Alarm Sensitivity (1-9; 0 = Pre-Alarm
not used) entered in the Detector Settings Screen.
• Cooperative Multi-Detector selection A smoke detector programmed to evaluate
readings from nearby detectors in making Alarm or Pre-Alarm decisions.
Cooperative Multi-Detector sensing also allows the combination of ionization with
photoelectric technology in reaching an alarm decision.
* – Multi-not used.
A – combines the detector's alarm decision with the next SLC address above.
B– combines the detector's alarm decision with the next SLC address below.
C – combines the detector's alarm decision with the next SLC address above and
the next SLC address below.
• Alarm Verification (* or V)
* – Alarm Verification not programmed for this detector.
V – Alarm Verification enabled.
Alarm Verification is a user-defined global time function that can reduce the
number of nuisance alarms. Refer to the glossary for a definition.
• Device SLC Address The SLC address of the detector.
How to View and Print Read Status Information
ENTER
, enter the SLC number followed
DETECTOR
key. For example, to read the status of
ENTER
, enter the SLC number, enter 203, then press the
7\SH &RGH ,21
/DEHO IRU WKH GHWHFWRU
$ 3$  9 '
' 'HWHFWRU
6/& QXPEHU  RU 
$ODUP 9HULILFDWLRQ VHOHFWLRQ
9 RQ RII
0XOWLGHWHFWRU VHOHFWLRQ
$ % & RU QRW VHOHFWHG
AFC-600 Operations PN 51033:A 3/8/99
key. You can now view
ENTER
6/& $GGUHVV