im Vertrieb von
12
Communication Parameters
Table 6
lists the communication parameters as used in Kramer Electronics
products.
Protocol 2000
Baud Rate:
Data Bits:
Stop Bits:
Parity:
Command Format:
Example (Output 1 to Input 1):
P2000 -> P3000
Command:
Front Panel:
Default Settings
IP Address: 192.168.1.39
Subnet mask: 255.255.255.0
Gateway: 192.168.1.1
TCP Port #: 5000
UDP Port #: 50000
13
Tables of ASCII Codes for Serial Communication
(Protocol 3000)
Table 7
and
VP-88K machine. For more detailed information, see
OUT 1
IN 1 #V 1>1 CR #V 1>2 CR #V 1>3 CR #V 1>4 CR #V 1>5 CR #V 1>6 CR #V 1>7 CR #V 1>8 CR
IN 2 #V 2>1 CR #V 2>2 CR #V 2>3 CR #V 2>4 CR #V 2>5 CR #V 2>6 CR #V 2>7 CR #V 2>8 CR
IN 3 #V 3>1 CR #V 3>2 CR #V 3>3 CR #V 3>4 CR #V 3>5 CR #V 3>6 CR #V 3>7 CR #V 3>8 CR
IN 4 #V 4>1 CR #V 4>2 CR #V 4>3 CR #V 4>4 CR #V 4>5 CR #V 4>6 CR #V 4>7 CR #V 4>8 CR
IN 5 #V 5>1 CR #V 5>2 CR #V 5>3 CR #V 5>4 CR #V 5>5 CR #V 5>6 CR #V 5>7 CR #V 5>8 CR
IN 6 #V 6>1 CR #V 6>2 CR #V 6>3 CR #V 6>4 CR #V 6>5 CR #V 6>6 CR #V 6>7 CR #V 6>8 CR
IN 7 #V 7>1 CR #V 7>2 CR #V 7>3 CR #V 7>4 CR #V 7>5 CR #V 7>6 CR #V 7>7 CR #V 7>8 CR
IN 8 #V 8>1 CR #V 8>2 CR #V 8>3 CR #V 8>4 CR #V 8>5 CR #V 8>6 CR #V 8>7 CR #V 8>8 CR
www.camboard.de
CAMBOARD Electronics
Communication Parameters
Table 6: Communication Parameters
9600
8
1
None
HEX
0x01, 0x81, 0x81, 0x81
Switching Protocol
0x38, 0x80, 0x83, 0x81
Press and hold Output 1 and Output 3
simultaneously
Reset Settings
Power cycle the unit while holding in the Factory Reset button, located on the
rear panel of the unit.
Table 8
list the ASCII codes that switch an input to an output for a single
Table 7: VP-88K Video Signal Codes
OUT 2
OUT 3
Tel. 07131 911201
Fax 07131 911203
RS-232
Protocol 3000 (Default)
Baud Rate:
Data Bits:
Stop Bits:
Parity:
Command Format:
Example (Output 1 to Input 1):
P3000 -> P2000
Command:
Front Panel:
Ethernet
Section 15.2
OUT 4
OUT 5
ce-info@camboard.de
115,200
8
1
None
ASCII
#AV 1>1<CR>
#P2000<CR>
Press and hold Output 1 and
Output 2 simultaneously
.
OUT 6
OUT 7
OUT 8
39
Need help?
Do you have a question about the VP-88K and is the answer not in the manual?