Solid State Logic Matrix Owner's Manual page 42

Chapter 3 - Analogue Signal Flow
A A u u x x i i l l i i a a r r y y S S e e n n d d s s
Matrix has six aux sends: one stereo cue and four mono effects (FX) sends.
Stereo Cue Send
The send to the stereo cue bus has a gain trim and pan pot, both of which have Total
Recall LEDs. Pressing the gain pot switches the send on and off. The
pot will light to indicate that it is on. The pan pot is indented in the middle, where the
signal is feeding both the left and right busses equally.
The stereo cue bus can be fed from four places: line-in pre-input-selection, pre-fader (post-insert), post-fader
or via SuperCue. The first three of these are selected by the
Channel, with pre-fader being the default setting.
The source is indicated by the LEDs between the pan and gain pots, and by the colour of the
S S i i g g n n a a l l S S o o u u r r c c e e
Pre-fader, post-insert, (default setting)
From the line-in, pre-gain
Post-fader
SuperCue monitoring (see below)
S S u u p p e e r r C C u u e e
When CUE is selected as the source in the
used to control the artist's headphone feed to provide full zero latency drop in and record monitoring for the artist. It works in
conjunction with the transport controls, summing the channel send and the DAW return when in Play, and automatically muting
the DAW return when in Record for a drop-in. The
SRC
by the button.
Note that for the SuperCue function to switch between corresponding DAW sends and returns, each DAW track output
must be sending to the Matrix channel which is feeding its input.
* Note that you can still cycle through the
Bass
the SRC button will not become active until the
through source options while in SuperCue mode, the
does not.
3 3 2 2 - - T T r r a a c c k k M M i i x x d d o o w w n n
When Matrix is being used for mixdown, and the channel is therefore being fed from the DAW return the
main channel input ('LINE IN') can be used to create an extra input channel, allowing for 32-track
mixdowns on one Matrix. This is done by selecting
above, and then pressing
then be fed from the CUE
than DAW return signal, as described below.
Note that when using the
requiring routing to the Insert Matrix.
1 2
11 12
Matrix Owner's Manual
34
10
10 10
5
5 5
ARTIST MONITOR
MIX REC
LEFT
SRC
TO MIX within the CUE ST
bus, enabling external processing to be assigned to the
CUE ST bus this way, the DAW returns should be fed by those signals
iJack
3 4
13
10 10
10 10
5 5
5 5
L L E E D D i i n n d d i i c c a a t t i i o o n n
No LED
INPUT is lit
POST
is lit
S-CUE
area of the centre section (see Page 39), SuperCue can be
MON SOLO
S-CUE button in the Master Channel overrides the source selection made
RIGHT
options when in SuperCue. However, the source selection indicated by
S-CUE button has been deselected. You will notice that if you cycle
SRC
button colour changes but the LED indication in the channel
INPUT as the source of the stereo cue, as described
area of the desk's centre section. FX sends can
iJack
5
14 15
10 10
10
5 5
5
ON LED below the
SRC button in the CUE ST
S S R R C C b b u u t t t t o o n n c c o o l l o o u u r r
Unlit
Red
Yellow
S-CUE is Green*
SolidStateLogic
INPUT signal rather
6 7
16
10
10 10
5
5 5
section of the Master
SRC button:
8
MASTER/FOCUS
10 10
0 10
5 5
5 5
DIM
M
9