J4 Pandaboard 4500 To Dlp Lightcrafter 4500 Interface; J6 Pandaboard 4500 To Dlp Lightcrafter 4500 Interface - Texas Instruments DLP LightCrafter 4500 User Manual

PandaBoard 4500
Table 6-3. J4 PandaBoard 4500 to DLP LightCrafter 4500 Interface
PandaBoard 4500 J4
Pin Signal I/O
1 VDD_V AUX2 PWR
2 VIO_1V8 PWR
3 h_DSS_DAT20 O
4 h_DSS_DAT21 O
5 h_DSS_DAT17 O
6 h_DSS_DAT18 O
7 h_DSS_DAT15 O
8 h_DSS_DAT16 O
9 h_DSS_DAT7 O
10 h_DSS_DAT13 O
11 h_DSS_DAT8 O
12 NUSB_PWR O
13 h_DSS_DAT9 O
14 H_I2C2_SCL O
15 h_DSS_DAT6 I/O
16 h_DSS_PCLK O
17 h_DSS_DEN O
18 h_DSS_HSYNC O
19 GND GND
20 GND GND
Table 6-4. J6 PandaBoard 4500 to DLP LightCrafter 4500 Interface
PandaBoard 4500 J6
Pin Signal I/O
1 VBUS_3 PWR
2 VBUS_4 PWR
3 USBH3_DM I/O
4 USBH4_DM I/O
5 USBH3_DP I/O
6 USBH4_DP I/O
7 DGND GND
8 DGND GND
GPMC_AD14 /
9 I/O
GPIO_38
GPMC_AD13 /
10 I/O
GPIO_37
SYS_NRESWA
11 I/O
RM
PB_POWER_O
12 I
N
13 HFL_P O
H_DMTIMER11
14 _PWM / O
GPIO121
15 HFL_N O
16 VDD_V AUX1 PWR
GPMC_AD12 /
17 I/O
GPIO_36
GPMC_AD8 /
18 I/O
GPIO_32
GPMC_W AIT0 /
19 I
GPIO_61
GPMC_AD9 /
20 I/O
GPIO_33
60
PandaBoard Interface
Description
Panda power rail
(adjustable from 1.2 V to 2.8 V)
Panda 1.8 V system I/O voltage
OMAP4 LCD pixel data bit 20
OMAP4 LCD pixel data bit 21
OMAP4 LCD pixel data bit 17
OMAP4 LCD pixel data bit 18
OMAP4 LCD pixel data bit 15
OMAP4 LCD pixel data bit 16
OMAP4 LCD pixel data bit 7
OMAP4 LCD pixel data bit 13
OMAP4 LCD pixel data bit 8
Input power enable
OMAP4 LCD pixel data bit 9
OMAP4 I2C2 serial clock
OMAP4 LCD pixel data bit 6
OMAP4 LCD pixel clock
OMAP4 LCD data enable
OMAP4 LCD horizontal sync
Ground bus
Ground bus
Description
OMAP4 VBUS output from USB Host Port
#3
OMAP4 VBUS output from USB Host Port
#4
OMAP4 USB host port 3 data minus
OMAP4 USB host port 4 data minus
OMAP4 USB host port 3 data plus
OMAP4 USB host port 4 data plus
Digital ground
Digital ground
OMAP4 GPMC address or data bit 14
OMAP4 GPMC address or data bit 13
Panda Warm Reset
Power on input to TWL6030 (ref. to VBAT)
Hands free left speaker out (+)
OMAP4 display PWM control
Hands free left speaker out (–)
TWL6030 VAUX1
OMAP4 GPMC address or data bit 13
OMAP4 GPMC address or data bit 8
OMAP4 GPMC Wait input 0
OMAP4 GPMC address or data bit 9
Copyright © 2013–2015, Texas Instruments Incorporated
DLP LightCrafter 4500 J4
Pin Signal I/O
1 NC
2 EXT_1V8 PWR
3 SYS_DATA20 I
4 SYS_DATA21 I
5 SYS_DATA17 I
6 SYS_DATA18 I
7 SYS_DATA15 I
8 SYS_DATA16 I
9 SYS_DATA7 I
10 SYS_DATA13 I
11 SYS_DATA8 I
12 NC
13 SYS_DATA09 I
14 SYS_I2C1_SCL I
15 SYS_DATA06 I/O
16 SYS_PCLK I
17 SYS_DATA_EN I
18 SYS_HSYNC I
19 GND GND
20 GND GND
DLP LightCrafter 4500 J6
Pin Signal I/O
1 NC
2 NC
3 SYS_USB_DN I/O
4 NC
5 SYS_USB_DP I/O
6 NC
7 GND GND
8 GND GND
9 DRV_GPIO11 O
10 DRV_GPIO12 O
11 NC
12 NC
13 NC
14 SYS_GPIO5 I
15 NC
16 NC
17 SYS_GPIO6 I
18 DRV_GPIO00 O
19 SYS_TRIGGER_SEL I
20 SYS_UART_SEL I
DLPU011E – July 2013 – Revised September 2015
www.ti.com
Description
No connect
1.8 V supplied by Panda
DLPC350 P1_C_6 level-shifted to 1.8 V
DLPC350 P1_C_7 level-shifted to 1.8 V
DLPC350 P1_C_3 level-shifted to 1.8 V
DLPC350 P1_C_4 level-shifted to 1.8 V
DLPC350 P1_B_9 level-shifted to 1.8 V
DLPC350 P1_C_2 level-shifted to 1.8 V
DLPC350 P1_A_9 level-shifted to 1.8 V
DLPC350 P1_B_7 level-shifted to 1.8 V
DLPC350 P1_B_2 level-shifted to 1.8 V
No connect
DLPC350 P1_B_3 level-shifted to 1.8 V
DLPC350 I2C1_SCL level-shifted to 1.8 V
DLPC350 P1_A_8 level-shifted to 1.8 V
DLPC350 P1_CLK level-shifted to 1.8 V
DLPC350 P1_DATAEN level-shifted to 1.8 V
DLPC350 P1_HSYNC level-shifted to 1.8 V
Digital ground
Digital ground
Description
No connect
No connect
TS3USB221 USB DN
No connect
TS3USB221 USB DP
No connect
Digital ground
Digital ground
DLPC350 GPIO11 (ClockC output) level-shifted
to 1.8 V
DLPC350 GPIO12 (ClockD output) level-shifted
to 1.8 V
No connect
No connect
No connect
DLPC350 GPIO5 (PWM0 input) level-shifted to
1.8 V
No connect
No connect
DLPC350 GPIO6 (PWM1 input) level-shifted to
1.8 V
DLPC350 GPIO0 (PWM0 output) level-shifted to
1.8 V
When high routes DLPC350 trigger inputs to
Pandaboard. When low routes DLPC350 trigger
Inputs to DLP LightCrafter 4500 input trigger
connector.
When high routes the DLPC350 UART to
Pandaboard. When low routes the DLPC350
UART to the DLP LightCrafter 4500 UART
connector.
Submit Documentation Feedback