Related Manuals for Texas Instruments DLP LightCrafter Display 3310
Summary of Contents for Texas Instruments DLP LightCrafter Display 3310
- Page 1 ® LightCrafter™ Display 3310 EVM User's Guide User's Guide Literature Number: DLPU063 January 2018...
-
Page 2: Table Of Contents
Contents ® ..............LightCrafter™ Display 3310 EVM Overview ....................... Safety Instructions ......................Applicable Documents ..............DLP LightCrafter Display 3310 EVM Components ........................Light Engine ......................Quick-Start Procedure ......................Circuit Description ................Connectors and Switches on System Board ................ Connectors on DLP LightCrafter Display Board ......................... - Page 3 DLP LightCrafter Display EVM List of Tables ....................5-1. Optical Engine Specifications ..............6-1. LEDs on the DLP LightCrafter Display 3310 EVM ................7-1. Connectors and Switches on System Board ..............7-2. Connectors on the DLP LightCrafter Display Board DLPU063 – January 2018...
-
Page 4: Dlp ® Lightcrafter™ Display 3310 Evm Overview
It explains the first steps to getting started and shows a detailed description of on board LEDs, connectors, and overall EVM assembly. It will give the user a start with their first DLP LightCrafter Display 3310 evaluation module. HDMI Connector... -
Page 5: Safety Instructions
May be harmful to the eye. WARNING Observe handling precautions. Electrostatic sensitive devices. WARNING Always ensure all fans are running during operation to help avoid overheating and ensure reliable operation. DLPU063 – January 2018 Safety Instructions Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... -
Page 6: Applicable Documents
Chapter 3 DLPU063 – January 2018 Applicable Documents The following documents are applicable to the DLP LightCrafter Display 3310 EVM and are available at TI.com (www.ti.com). • DLP3310 0.33 1080p DMD (DLPS077) • DLPA3000 PMIC and High-Current LED Driver IC (DLPS052) •... -
Page 7: Dlp Lightcrafter Display 3310 Evm Components
Chapter 4 DLPU063 – January 2018 DLP LightCrafter Display 3310 EVM Components The DLP LightCrafter Display module consists of three subsystems: • Light engine – Includes the optics, red, green, and blue LEDs, and a Full-HD DMD capable of 300 lumens out-of-the-box. -
Page 8: Light Engine
Brightness at 6-A RGB LED Current RGB LED Current Brightness Uniformity Throw Ratio Offset 100% Focusable Diagonal Image Size inch 30.00mm 87.70mm Figure 5-1. Optical Engine Dimensions Light Engine DLPU063 – January 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... -
Page 9: Optical Engine View
Figure 5-2. Optical Engine View DLPU063 – January 2018 Light Engine Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... -
Page 10: Quick-Start Procedure
5-V power and 3.3-V power are applied. 2. Move SW2 switch to the ON position to turn on the DLP LightCrafter Display 3310 EVM. When the DLP LightCrafter Display 3310 EVM is turned on, the PROJ_ON LED (D5) will turn on. -
Page 11: Leds On The Dlp Lightcrafter Display 3310 Evm
Table 6-1. LEDs on the DLP LightCrafter Display 3310 EVM Signal Board LED Reference Description Indication System P5V_VIN Regulated 5-V power on. ON when Cypress CY65215 requests the MSP430 to give Cypress master System MSP430_REQ control of the I C bus. -
Page 12: Connectors And Switches On System Board
Connector for the DMD interface flex cable. Connector for Red LED cable. Connector (60-pin) for FPD interface. Connector (60-pin) for DLP LightCrafter System board interface. Circuit Description DLPU063 – January 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... -
Page 13: Evm Setup
Chapter 8 DLPU063 – January 2018 EVM Setup The DLP LightCrafter Display 3310 EVM is composed of three parts: • System board • DLP LightCrafter Display board • Engine with LED connections and Flex cables The system board contains the connector for the power supply, a USB connector to communicate to the DLP LightCrafter Display software, HDMI, and the connector for the DLP LightCrafter Display board. -
Page 14: Dlp Lightcrafter Display Evm
Always ensure a good connection of the flex cables and LED cables to the DLP LightCrafter Display board before turning it on. Flex Cable Connector Red/Green/Blue LED Connectors Actuator Flex Cable Connector Figure 8-3. DLP LightCrafter Display EVM EVM Setup DLPU063 – January 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... - Page 15 IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products;...
- Page 16 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments DLPDLCR3310EVM...
Need help?
Do you have a question about the DLP LightCrafter Display 3310 and is the answer not in the manual?
Questions and answers