[E] Monitor-To-Monitor Data Copy - Copy From Menu; Overview; Structure Of The Copy From Menu; Setting Lists Of The Copy From Menu - Sony BVM-D32E1WA Maintenance Manual

[E]
Monitor-to-Monitor Data Copy
— COPY FROM Menu

Overview

When multiple BVM-DxxE/DxxF series monitors are
connected via their serial remote ports, data can be
shared between the monitors by data copy. The data
copy from one monitor to another is accomplished
with the COPY menu.
Note
Data copy is impossible between monitors other than
BVM-DxxE/DxxF series.

Structure of the COPY FROM Menu

Main Menu Level 1 Level 2
COPY FROM E MONITOR ADDRESS E1 ALL
CONTROL PRESET
CONTROL TEMP
SET UP

Setting Lists of the COPY FROM Menu

This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see "About
menu numbers" on page 23.
• The arrow mark (÷) refers you to another setting
list that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
58
First assign the MONITOR ADDRESS from which
the data is to copy, then select the data from among the
following:
• Copying data for all menu settings (ALL menu)
• Copying data for the CONTROL PRESET ADJ
menu settings (CONTROL PRESET menu)
• Copying data for the COLOR TEMP ADJ menu
settings (COLOR TEMP menu)
• Copying data for the SET UP menu settings (SET
UP menu)
[E] COPY FROM menu
Select the copy source monitor.
MONITOR ADDRESS: Enter the monitor address
number. ÷[E1]
[E1] MONITOR ADDRESS menu
Select the data to be copied. ÷ Copy is carried out.
ALL: Copy data for all menu settings.
CONTROL PRESET: Copy the data for the
CONTROL PRESET ADJ menu settings.
COLOR TEMP: Copy the data for the COLOR
TEMP ADJ menu settings.
SET UP: Copy the data for the SET UP menu settings.
[F]
Displaying Information About the Monitor

— STATUS Menu

Overview
The STATUS menu is used to view general data about
the monitor status, the current channel, etc.
The following information is displayed on the three
pages of the STATUS menu.

Structure of the STATUS Menu

Main Menu Level 1
STATUS (1/3) F1
STATUS F
STATUS (2/3) F2
STATUS (3/3) F3

Setting Lists of the STATUS Menu

This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see "About
menu numbers" on page 23.
• The arrow mark (÷) refers you to another setting
list that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
[F] STATUS menu
Select the STATUS menu 1/3, 2/3 or 3/3. ÷ [F1]
[F1] STATUS menu (1/3)
Specify the channel block to be detected from channel
1 to channel 99.
[F11] CH STATUS menu (1/3)
Data about the current channel is displayed.
CH: channel number
SL: slot number
IN: input connector number
FORMAT: format of the input signal
NAME: channel name
• Data about the current channel (STATUS menu
(1/3))
• Data about the monitor in use (STATUS menu (2/3))
• Data about the circuit boards installed into the
slots in the rear panel (STATUS menu (3/3))
Level 2 Level 3
CH STATUS F11 CH
MODEL NAME
SLOT STATUS F31 MODEL NAME
SERIAL NO
[F2] STATUS menu (2/3)
Data about the monitor is displayed.
MODEL NAME: model name
SERIAL NO: serial number
OPERATION TIME: operation time (in hours)
SOFTWARE VERSION: software version
[F3] STATUS menu (3/3)
Data about circuit boards installed into the respective
slots in the rear panel is displayed. When the BKM-
21D is installed in SLOT 2, the following is displayed.
When any optional boards are not installed, EMPTY is
displayed for SLOT 2 to SLOT 5.
SLOT1: CONTROL
SLOT2: SDI4:2:2/4FSC
SLOT3: EMPTY
SLOT4: EMPTY
SLOT5: EMPTY
SLOT6: VIDEO AMP
SLOT7: DEFLECTION
SLOT8: EMPTY (BVM-D20F1U/D20F1E/D20F1A)
or DIGITAL UNIF (BVM-D24E1WU/
D24E1WE/D24E1WA/D32E1WU/
D32E1WE/D32E1WA)
SLOT9: POWER SUPPLY
[F31] SLOT STATUS menu
Select the desired slot. Data about the optional board
installed in the selected slot is displayed.
MODEL NAME: Model name of that optional board
SERIAL NO: Serial number of that circuit board
59