[C6]Adjusting Geometry And Convergence (Set Up 6) - Alignment Menu; Overview; Structure Of The Alignment Menu; Setting Lists Of The Alignment Menu - Sony BVM-D32E1WA Maintenance Manual

[C6]
Adjusting Geometry and Convergence
(SET UP 6) — ALIGNMENT Menu

Overview

The ALIGNMENT menu is used for adjusting
geometry and convergence.
Note
Adjust the beam landing ([C8]) after the geometry and
convergence adjustments have been completed.
The following adjustments can be performed with the
three pages of the ALIGNMENT menu.

Structure of the ALIGNMENT Menu

Level 1 Level 2
INPUT CONFIGURATION C1
REMOTE C2
PASSWORD C3
SYSTEM CONFIGURATION C4
ON SCREEN SET C5
ALIGNMENT C6 ALIGNMENT (1/3) — ROTATION
WHITE UNIFORMITY C7
ALIGNMENT (2/3) — H PIN
EXTEND MENU C8
ALIGNMENT (3/3) — V STATIC CONV
CONV FINE ADJUST... C61 — ADJUST C611
1) BVM-D32E1WU/D32E1WE/D32E1WA only

Setting Lists of the ALIGNMENT Menu

This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see "About
menu numbers" on page 23.
48
• Adjusting the position and size of the picture
(ALIGNMENT menu (1/3))
• Adjusting the geometry of the picture
(ALIGNMENT menu (2/3))
• Adjusting the convergence (ALIGNMENT menu
(3/3))
Level 3 Level 4
1) 1)
• The arrow mark (÷) refers you to another setting
list that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
[C6] ALIGNMENT menu (1/3)
Adjust the position or size of the picture with the UP
and DOWN buttons or PHASE knob.
ROTATION: Compensates for the screen rotation
which occurs when the monitor is installed facing
north or south.
H PHASE: Adjust the horizontal picture position.
V CENTER: Adjust the vertical picture position.
H SIZE: Adjust the width of the picture.
V SIZE: Adjust the height of the picture.
VITS BLK: Adjust vertical blanking so that VITS
signals are not visible in the upper part of the
screen.
SUB CONTRAST: Adjust the center value of the
contrast when the image size or signal format is
changed.
[C6] ALIGNMENT menu (2/3)
Adjust the geometry of the picture with the UP and
DOWN buttons or PHASE knob.
H PIN: Correct side pincushion distortion.
H PIN BAL: Correct the balance of side pincushion
distortion.
H CORNER PIN: Correct pincushion distortion at the
sides of the picture.
H CORNER S: Correct S pincushion distortion at the
sides of the picture.
H KEY: Correct trapezoid distortion.
H KEY BAL: Correct the balance of trapezoid
distortion.
[C6] ALIGNMENT menu (3/3)
Adjust the convergence with the UP and DOWN
buttons or PHASE knob.
V STATIC CONV: Adjust vertical static convergence
on the whole screen.
V CONV TOP: Adjust vertical convergence at the top
of the screen. (BVM-D20F1U/D20F1E/D20F1A/
D24E1WU/D24E1WE/D24E1WA only)
V CONV BOT: Adjust vertical convergence at the
bottom of the screen. (BVM-D20F1U/D20F1E/
D20F1A/D24E1WU/D24E1WE/D24E1WA only)
H STATIC CONV: Adjust horizontal static
convergence on the whole screen.
CONV FINE ADJUST... : Adjust the convergence
finely at each adjustment point on the screen.
÷[C61] (BVM-D32E1WU/D32E1WE/
D32E1WA only)
49