[C4]Setting The Channel Selection Method, Power-Up Conditions; Menu; Overview; Structure Of The System Configuration Menu - Sony BVM-D32E1WA Maintenance Manual

[C4]
Setting the Channel Selection Method, Power-Up Conditions
and Decoder (SET UP 4) — SYSTEM CONFIGURATION Menu

Overview

The SYSTEM CONFIGURATION menu is used for
the following settings:
• Channel number entry method (INPUT SELECT

menu)

This menu sets the way in which the numeric keypad
can be used to enter channel numbers.
• Power-up condition (STANDBY MODE menu)
This menu sets the condition of the monitor when the
MAIN POWER switch on the rear panel is switched
on.
• Power-up input channel (DEFAULT CH menu)
This menu sets the power-up input channel.
• Time from power-up until degauss (DEGAUSS
DELAY menu)
If several monitors are turned on at the same time and
all start degaussing at the same time, there will be a
very large current draw on the power supply for a few
moments. To prevent this, the delay time between
power-up and degaussing can be set for each monitor
independently.

Structure of the SYSTEM CONFIGURATION Menu

Level 1 Level 2
INPUT CONFIGURATION C1
REMOTE C2
PASSWORD C3
SYSTEM CONFIGURATION C4 INPUT SELECT
STANDBY MODE
ON SCREEN SET C5
DEFAULT CH
ALIGNMENT C6
WHITE UNIFORMITY C7 DEGAUSS DELAY
EXTEND MENU C8 RESIDUAL SC SW
ACC SW
CONT/BRT HOLD
COL TEMP SHORT-CUT
44
• Residual subcarrier detection (RESIDUAL SC
SW menu) (when using the BKM-24N/25P)
It is possible to detect residual subcarrier signals from
phase change by setting the decoder adpator's
residual subcarrier switch on.
• Auto color control (ACC SW menu) (when using
the BKM-27T)
Selects if the ACC (Auto Color Control) circuit is
activated or deactivated.
• Setting of the contrast and brightness after
adjusting the white balance (CONT/BRT HOLD
menu)
Selects if the adjusted contrast and brightness are
retained or they are reset to the center values.
• Assigning shortcut to the COLOR TEMP ADJ
menu to the [F2] key (COL TEMP SHORT-CUT
menu)
Assigns the shortcut to the MANUAL menu of the
COLOR TEMP ADJ menu to the [F2] key. This
allows you to jump directly to the MANUAL menu
corresponding to the color temperature set to the
currently displayed image (STD/COL 1/COL 2/CH
SET).

Setting Lists of the SYSTEM CONFIGURATION Menu

This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see "About
menu numbers" on page 23.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[C4] SYSTEM CONFIGURATION menu
Set each of the following items.
INPUT SELECT: Select the channel number
selection method (DIRECT or 10KEY).
(In the explanation below, x and y represent any
digit between 0 and 9.)
DIRECT mode: When selecting a number from 1
to 9, press the x button to display channel x.
When selecting a number from 10 to 99, press
the 0, x, and y buttons to display channel xy (a
two-digit channel number). This mode is
selected at the shipping.
10KEY mode: When the x button is pressed
followed by the ENTER or Ent button, the
monitor displays channel x. When the x buttons
is pressed, followed by the y and ENTER (Ent)
buttons, the monitor displays channel xy (a two-
digit channel number).
When multiple monitors are connected by a
serial remote connection, this setting will be
common to all the monitors. It is not possible to
change the setting for individual monitors.
STANDBY MODE: Select the power-up condition
when the MAIN POWER switch is turned on (OFF
or ON).
ON: Standby mode
OFF: Operation mode
DEFAULT CH: Select the power-up input channel
(LAST or CH xx).
LAST: Set the channel to the channel that was
selected at the time the power was last turned
off.
CH xx: Set the channel to a specific channel
number.
DEGAUSS DELAY: Set the time between power-up
and the beginning of degaussing. Enter the desired
time (in seconds).
RESIDUAL SC SW: Set the residual switch (OFF or
ON).
ACC SW: Set the ACC switch (OFF or ON).
CONT/BRT HOLD: Select the contrast and
brightness settings to the center or adjusted value
after adjusting the white balance or auto
adjustment of CONTROL PRESET ADJ (OFF or
ON).
ON: The contrast and brightness are set to the
value before adjusting.
OFF: The contrast and brightness are set to the
center value (1000) after adjusting.
COL TEMP SHORT-CUT: Assign the shortcut
function to the MANUAL menu of the COLOR
TEMP ADJ menu to [F2] key (OFF or ON).
ON: Assigns the shortcut to the MANUAL menu
of the COLOR TEMP ADJ menu.
OFF: Does not assign the shortcut to the
MANUAL menu of the COLOR TEMP ADJ
menu.
45