Main Room Basic Operations; Turning The Power On And Off (Standby) - JVC RX-9010VBK Service Manual

Main Room Basic Operations

This section explains only the operations commonly used when you play any sound source in the main room.
See pages 23 for the sub-room operations.
You can use "On-screen Menu" for most of the main room operations. For details, see page 50.
IMPORTANT:
Check to see if the proper indicator(s) and information appear on the
display on the front panel before/while using the buttons and controls.
For the main room operations:
• The MAIN ROOM indicator is lit.
• The source name for the sub-room is not lit on
the display.
• When using the remote control:
– Set MAIN ROOM/SUB ROOM selector to
"MAIN ROOM."
– Check to see if the following informations
appear on the display window on the remote control:
MAIN ROOM/
SUB ROOM selector
MAIN ROOM
SUB ROOM
Buttons
FM/AM
CD
PHONO
TAPE/MD
DVD or DVD MULTI
CDR
USB AUDIO
TV/DBS
VCR 1
VCR 2
VIDEO
SOUND
After pressing SOUND:
DIGITAL EQ
Ex. When you press CD with
MAIN ROOM/SUB ROOM
selector set to "MAIN
ROOM."
When you set MAIN ROOM/SUB ROOM selector* and press the
buttons listed above, the corresponding indication appears for 10
seconds for your confirmation.
Notes:
* MAIN ROOM or SUB ROOM indicator does not appear when no
indicators appear on the display window.
** When you set TV/CATV/DBS selector to "CATV/DBS," "CATV"
appears as the indication. (See page 68.)
17
MAIN ROOM SUB ROOM
Indications
*
MAIN ROOM
*
SUB ROOM
Indications
TUNER
CD
PHONO
TAPE
DVD
CDR
USB
TV**
VCR 1
VCR 2
VIDEO
SOUND
EQ
STANDBY ON
MAIN ROOM SUB ROOM
MAIN ROOM SUB ROOM TV/CATV/DBS VCR1
ON/OFF ON/OFF POWER POWER
MAIN ROOM SUB ROOM

Turning the Power On and Off (Standby)

On the front panel:
To turn on the power, press POWER.
The STANDBY lamp on the front panel goes
off, and the MAIN ROOM indicator lights up
on the display. The name of the current main
room source and Surround/DSP mode appear on
the display.
Current source name and Surround/DSP modes for
the main room appear
L R
ANALOG
SPEAKERS
1
Current volume level for the main room is shown here
The currently selected SPEAKERS 1 and/or 2 indicator(s) also light
up on the display.
• If the SPEAKERS 1 and/or 2 indicator(s) are not lit on the display,
see "Activating the Main Room Front Speakers" on page 19.
To turn off the power (into standby mode),
press POWER again.
The STANDBY lamp lights up. A small
amount of power is consumed in standby
mode. To turn the power off completely,
unplug the AC power cord.
From the remote control:
To turn on the power, press
AUDIO POWER ON.
The STANDBY lamp on the front panel
goes off, and the MAIN ROOM indicator
lights up on the display. The name of the
current main room source and Surround/DSP
mode appear on the display.
The currently selected SPEAKERS 1 and/or 2 indicator(s) also light
up on the display.
• If the SPEAKERS 1 and/or 2 indicator(s) are not lit on the display,
see "Activating the Main Room Front Speakers" on page 19.
To turn off the power (into standby mode),
press AUDIO POWER STANDBY.
The STANDBY lamp lights red.*
Notes:
• When you turn off the receiver in the main room, make sure if other
people are listening to any source in the sub-room (the SUB ROOM
and SPEAKERS SUB ROOM indicators are lit on the display).
• If you have turned off the receiver with the volume level set at more
than level "40," the volume level will be automatically set at level
"40" next time you turn on the receiver.
• If "TURN ON MAIN OR SUB ROOM" appears on the display, press
MAIN ROOM ON/OFF or SUB ROOM ON/OFF to listen to the
sound in the main room or in the sub-room; otherwise, the receiver
will turn off after about 1 minute. In this case, the receiver is turned
on with the main room operations activated by pressing POWER
(AUDIO POWER ON on the remote control).
STANDBY
POWER
MAIN ROOM
VOLUME
STANDBY
POWER
STANDBY ON
STANDBY ON