Operating Other Manufacturers' Equipment - JVC RX-9010VBK Service Manual

Operating Other Manufacturers' Equipment

This remote control supplied with the receiver can transmit control signals for other manufacturers' VCRs, TVs, CATV
converters, DBS tuners, DVD players ,and CD players. By changing the transmittable signals from preset ones to the
other manufacturers', you can operate the other manufacturer's components using this remote control.
When operating the other manufacturers' components, refer also to the manuals supplied with them. To operate these
components with the remote control, first you need to set the manufacturer's code each for VCR, TV, CATV converter,
DBS tuner, and DVD player.
After replacing batteries of the remote control, set the manufactures' codes again.
IMPORTANT:
• To operate the video component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor on the target video component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals at a distance of 10 feet
(3 m).
When using the remote control:
Check to see if TV/CATV/DBS selector are set to the correct position:
TV/CATV/DBS selector:
• For TV operations
Set TV/CATV/DBS selector to "TV."
• For the CATV converter and DBS tuner
operations
Set TV/CATV/DBS selector to "CATV/DBS."
• Check to see if the following information appear on the display
window on the remote control.
After setting the remote control mode selector to "TV" :
Buttons
TV/DBS
VCR 1
DVD or DVD MULTI
CD
DVD MENU
After setting the remote control mode selector to "CATV/DBS" :
Buttons
TV/DBS
VCR 1
DVD or DVD MULTI
CD
DVD MENU
After selecting a source:
Buttons
PLAY
4
¢
STOP
PAUSE
1 – 9, 0, +10, 100+
CHANNEL +/–
After pressing DVD MENU:
Buttons
%, fi, @, #, SET
When you press the buttons listed above, the indication appears
for 5 – 10 seconds for your confirmation.
Note:
All the functions may not be assigned to the buttons in some
equipment.
TV
CATV/
DBS
Indications
TV
VCR 1
DVD
CD
DMENU
Indications
CATV
VCR 1
DVD
CD
DMENU
Indications
one of the source
names listed above
VCR1 or TV
Indications
DMENU
To change the transmittable signals for
operating another manufacturer's TV
1. Set TV/CATV/DBS selector to "TV."
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer's code using buttons 1–9,
and 0.
See page 70 to find the code.
5. Release TV/CATV/DBS POWER.
After setting TV/CATV/DBS selector to "TV," you can perform
the following operations on the TV:
TV/CATV/DBS POWER: Turns on and off the TV.
TV VOL +/–:
TV/VIDEO:
After pressing TV/DBS (with the remote control mode selector
set to "TV"), you can perform the following operations on a TV:
CHANNEL +/–:
1 – 10, 0, 100+ (+10):
Notes:
• Refer to the manual supplied with your TV.
• You cannot change the channels of some TVs by pressing
number buttons. In this case, press CHANNEL +/– for
changing the channels.
6. Try to operate your TV by pressing
TV/CATV/DBS POWER.
When your TV turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
Adjusts the volume.
Sets the input mode (either TV
or VIDEO).
Changes the channels.
Selects the channels.
The 10 button will function as the
ENTER button if your TV requires
pressing ENTER after selecting a
channel number.
Continued to the next page.
68