Operating Jvc's Audio/Video Components; Operating Audio Components - JVC RX-9010VBK Service Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.

Operating Audio Components

IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-4 (SYNCHRO) jacks (see page 55) in addition to the
connections using cables with RCA pin plugs (see pages 7 and 8).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source. To
operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 33.)
• Refer also to the manuals supplied with your components.
When using the remote control supplied with this receiver:
• For the main room operations
– Set MAIN ROOM/SUB ROOM selector to "MAIN ROOM."
• For the sub-room operations
– Set MAIN ROOM/SUB ROOM selector to
"SUB ROOM."
– Check to see if the following information
appear on the display window on the remote
control:
MAIN ROOM/
SUB ROOM selector
MAIN ROOM
SUB ROOM
* MAIN ROOM or SUB ROOM indicator does not appear when no
indicators appear on the display window.
Buttons
FM/AM
CD
CDR
PHONO
TAPE/MD
CONTROL (repeatedly)
SOUND
After selecting a source:
Buttons
PLAY
4/REW
FF/¢
STOP
PAUSE
1 – 10, +10, 0
After pressing SOUND, the following function are
assigned to the specific number buttons:
Buttons
BALANCE L
BALANCE R
EFFECT
ROOM SIZE
LIVENESS
CENTER TONE
SUBWFR
CENTER
REAR•L
REAR•R
DIGITAL EQ
When you press the buttons listed above, the indication appears
for 5 – 10 seconds for your confirmation.
65
MAIN ROOM SUB ROOM
Indications
*
MAIN ROOM
*
SUB ROOM
Indications
TUNER
CD
CDR
PHONO
TAPE
VCR1 = TAPE = CDR =
CDDSC = (back to the beginning)
SOUND
Indications
one of the selected
source names listed
above
Indications
SOUND
S WFR
CTR
REARL
REARR
EQ
Tuner
You can always perform the following operations:
FM/AM:
Alternates between FM and AM.
After pressing FM/AM, you can perform the following operations:
1 – 10, +10:
Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
TUNING UP/DOWN: Tunes into stations.
FM MODE:
Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND ON/OFF:
DSP MODE:
TEST:
After pressing SOUND, you can perform the following operations:
SUBWFR then LEVEL +/–: Adjusts the subwoofer output level.
CENTER then LEVEL +/–: Adjusts the center speaker output
REAR•L then LEVEL +/–:
REAR•R then LEVEL +/–:
DIGITAL EQ then LEVEL +/–: Selects the audio band and adjusts its
BALANCE L/BALANCE R: Adjusts the output balance of the
EFFECT:
CENTER TONE:
ROOM SIZE:
LIVENESS:
Notes:
• After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
• Each time you press LEVEL + or LEVEL –, the indication
corresponding to the function you have selected appears on the
display window on the remote control.
CD player
After pressing CD, you can perform the following operations on the
CD player:
PLAY:
Starts playing.
4:
Returns to the beginning of the current (or
previous) track.
¢:
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE:
Pauses playing. To release it, press PLAY.
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Turns on or off the Surround modes
— Dolby Pro Logic, Dolby Digital,
and DTS Digital Surround.
Selects the DSP modes.
Turns on or off the test tone output.
level.
Adjusts the left rear speaker output
level.
Adjusts the right rear speaker output
level.
frequency level.
front speakers.
Selects the effect level.
Selects the center tone.
Selects the room size.
Selects the liveness.