Zone 1 (Main Room) Operations; Turning The Power On And Off (Standby) - JVC RX-DP15BC Instructions Manual

Zone 1 (Main Room) Operations

This section explains only the operations commonly used when you play any sound source in Zone 1 (main room).
See pages 29 to 32 for the Zone 2 (sub-room) operations.
• Before performing Zone 1 operations, it is recommended to finish the basic settings on pages 35 to 44.
IMPORTANT:
Check the following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 ON/OFF lamp on the unit is lit.
• When using the unit:
– "ZONE 2" is not shown in the main display.
– Press DOOR DOWN to use the buttons inside the
front door.
To close the front door, press DOOR UP.
• When using the remote control:
– Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to "ZONE 1."
– Check the indication shown on the remote's display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either ZONE 1 or
ZONE 2) for a while.
LEARN TRANSMIT
ZONE 1 ZONE 2
Ex. When you press FM/AM with ZONE 1/ZONE 2
(LEARN/TRANSMIT) selector set to "ZONE 1."

Turning the Power On and Off (Standby)

On the unit:
To turn on the power, press
The STANDBY lamp goes off, and the ZONE 1 ON/OFF lamp
lights up. The front door moves down (so that the source selecting
buttons appear).
STANDBY
STANDBY/ ON
The last Zone 1 source is activated.
ANALOG
L R
SUBWFR
The last Surround/THX/DSP mode
appears.
The currently selected speakers 1 and/or 2 indicator(s) also light(s)
up on the display.
• If neither speakers 1 nor 2 indicator is lit on the display, see
"Activating the Zone 1 Front Speakers" on page 25.
DOOR
DOWN
LEARN TRANSMIT
STANDBY
ON
ZONE 2
ZONE 1
ZONE 1 ZONE 2 TV/CATV/DBS
VCR 1
ON/OFF ON/OFF
STANDBY/ON STANDBY/ON
ZONE 1
(STANDBY/ON).
ZONE 1
ON/OFF
SPEAKERS 1
VOLUME
The volume
level appears.
To turn off the power (into standby mode),
press (STANDBY/ON) again.
The STANDBY lamp lights up, and the front
door automatically closes. (The ZONE 1 ON/
OFF and/or ZONE 2 ON/OFF lamp goes off.)
• A small amount of power is consumed in standby mode. To turn
the power off completely, unplug the AC power cord.
From the remote control:
To turn on the power, press AUDIO (ON).
The STANDBY lamp on the unit goes off,
and the ZONE 1 ON/OFF lamp on the unit
lights up.
The front door moves down (so that the source
selecting buttons appear).
The last Zone 1 source is activated.
ANALOG
L R
SUBWFR
The last Surround/THX/DSP
mode appears.
The currently selected speakers 1 and/or 2 indicator(s) also light(s)
up on the display.
• If neither speakers 1 nor 2 indicator is lit on the display, see
"Activating the Zone 1 Front Speakers" on page 25.
To turn off the power (into standby mode),
press AUDIO (STANDBY).
The STANDBY lamp lights up, and the front
door automatically closes. (The ZONE 1 ON/
OFF and/or ZONE 2 ON/OFF lamp on the unit
goes off.)
Notes:
• Before you turn off the receiver in Zone 1, make sure that no one is
listening to any source in Zone 2 (the ZONE 2 ON/OFF lamp is lit
on the display) since the Zone 2 sound will also be turned off
unexpectedly.
• If you have turned off the receiver with the volume level set at more
than level "–35 dB," the volume level will be automatically set at
level "–35 dB" next time you turn on the receiver.
When you turn on the TV connected to the TV SOUND/DBS IN
jacks on the rear
This receiver automatically turns on and selects "TV" as the Zone 1
source about 5 seconds after you turn on the TV. (If you change the
dB dB
source name from "TV" to "DBS," the receiver will not turn on
along with the TV. See "Changing the Source Name" on page 27.)
STANDBY
STANDBY/ON
STANDBY ON
SPEAKERS 1
VOLUME
dB dB
The volume
level appears.
STANDBY
ON
22