Teledyne m640 User Manual page 85

Pulse on: Action 1
Pulse on: Action 2
Pulse on: Software
Command
Exposure Active
Output Line Pulse Signal
Activation
Rising Edge
Falling Edge
Any Edge
Output Line Pulse Delay
Output Line Pulse Duration
Output Line Value
Active
Inactive
Output Line Software Latch
Control
Off
Latch
Flash Zone Delay
Flash Zone Duration
Output Line Software
Command
Line Pinout
Pin5=Signal – Pin3=Gnd
Pin7=Signal – Pin3=Gnd
Pin6=Signal – Pin4=Pwr
Nano Series GigE Vision Camera
PulseOnAction1
PulseOnAction2
PulseOnSoftwareCmd
ExposureActive
outputLinePulseActivation
RisingEdge
FallingEdge
AnyEdge
outputLinePulseDelay
outputLinePulseDuration
outputLineValue
Active
Inactive
outputLineSoftwareLatchControl
Latch
flashZoneDelay
flashZoneDuration
outputLineSoftwareCmd
linePinAssociation
Pin5Signal_Pin3Gnd
Pin7Signal_Pin3Gnd
Pin6Signal_Pin4Pwr
Generate a pulse on the
GigEVision Action Command 1.
Generate a pulse on the
GigEVision Action Command 2.
Generate a pulse on the Input of a Software
Command
Generate a signal that is active when the Exposure
is active. <from v1.01>
Specifies the input line activation mode to trigger
the OutputLine pulse.
Specifies that the trigger is considered valid on the
rising edge of the source signal.
Specifies that the trigger is considered valid on the
falling edge of the source signal.
Specifies that the trigger is considered valid on the
falling or rising edge of the source signal.
Sets the delay (in µs) before the output line pulse
signal. Applicable for the OutputLineSource
feature.
Sets the width (duration) of the output line pulse in
microseconds.
Sets the output state of the selected Line if the
outputLineSoftwareLatchControl = OFF.
OutputLineSource must be SoftwareControlled. If
the outputLineSoftwareLatchControl = Latch , the
state of the pin will change with the
outputLineSoftwareCmd command.
Sets the Output circuit to close
Sets the Output circuit to open
When Off, the selected output line is set with the
value in Output Line Value.
Off Output pin state set by outputLineValue.
Output pin state set by outputLineSoftwareCmd.
Returns the recommended output pulse delay,
corresponding to the delay of the last line exposure
start of a rolling shutter sensor, when the Output
Line Source = Pulse on Start of Exposure. (RO)
Returns the recommended output pulse duration
for controlling a flash device for the optimal flash
zone time. (RO)
Writing a value of 1 in the bit field applies the
Latch value of the outputLineSoftwareLatchControl
and/or executes the PulseOnSoftwareCmd for any
output line programmed for software control. The
feature outputLineSoftwareCmd can take any
binary value and each bit set to 1 corresponds to a
Icommand for an Output. Note that Outputs are
numbered from 1 to N, therefore Bit 1 of
outputLineSoftwareCmd corresponds to Output1.
This is applicable to OutputLineSource = Pulse On:
where Software Cmd (for Pulse mode) or
OutputLineSource = SoftwareControlled and
OutputLineSoftwareLatchControl = Latch (for static
states).
Enumeration of the physical line (or pin) on the
device I/O connector. (RO)
Pin 5 is the Input Signal and Pin 3 is the common
input Ground on the I/O connector.
Pin 7 is the Input Signal and Pin 3 is the common
input Ground on the I/O connector.
Pin 6 is the Output Signal and Pin 4 is the common
output Power on the device connector.
(ver:1.03)
(ver:1.03)
1.00
Beginner
DFNC
1.00
Beginner
DFNC
1.00
Beginner
DFNC
1.00
Beginner
DFNC
1.00
Guru
DFNC
1.06
Guru
DFNC
Model C4900
1.06
Guru
DFNC
Model C4900
1.00
Expert
DFNC
1.00
Invisible
Operational Reference • 83