When wake-up on motion detection is enabled the system will automatically wake to the Halfwake state when people enter the room. It will also wake to this state when a user pairs a Cisco Proximity client to the system. D15328.07 SX80 Administrator Guide CE9.1, JUNE 2017.
The codec offers a rich input and output set, flexible media engine, and support for three screens enable various use cases. Cisco offers SX80 as a single unit, and in the following integrator packages: • SX80 and Precision 40 (PrecisionHD 1080p4xS2) camera for smaller room scenarios •...
Page 16
(CUCM, VCS); the pages shown in grey color are not available if the video system is registered to the Cisco cloud service (Cisco Spark). In both cases, a user that is signed in, sees only the pages that he has access rights for.
You can customize our touch user interfaces to include input sources that are connected to a third-party external video switch. You need a Cisco video system with a touch interface, a third- The sources will appear and behave as any other video source party control system, for example Crestron or AMX, and a third- that is connected directly to the video system.
Cameras Camera [n] Brightness DefaultLevel setting. Typical situations where the codec does not receive EDID information are: when you connect a Cisco TelePresence 60 camera using 3G-SDI; when you connect a Cisco TelePresence 60 (Cisco PrecisionHD 1080p4xS2) camera; when you use an HDMI repeater Cameras Camera [1..7] Brightness DefaultLevel...
This setting enables gamma corrections, and applies only to cameras which support gamma mode. Gamma describes the nonlinear relationship between image pixels and This setting applies only when using a Cisco TelePresence PrecisionHD 1080p12x camera. monitor brightness. If adjusting the camera position by hand you can configure whether the camera should keep its new position or return to the preset or position it had before.
Cameras Camera [1..7] Whitebalance Mode Cameras PresenterTrack CameraPosition Pan Define the camera white balance mode. This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera or SpeakerTrack 60 camera. Requires user role: ADMIN, INTEGRATOR Define the pan position which the presenter tracking camera will move to when the feature Default value: Auto is activated.
Appendices Cameras PresenterTrack Connector Cameras PresenterTrack TriggerZone This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera or SpeakerTrack 60 camera. or SpeakerTrack 60 camera.
Cameras SpeakerTrack TrackingMode This setting applies only when using a Cisco TelePresence SpeakerTrack 60 camera. This setting applies only when using a Cisco TelePresence SpeakerTrack 60 camera, and when Cameras SpeakerTrack Mode is set to Auto. The SpeakerTrack 60 camera assembly consists of two cameras and uses an audio tracking technique that finds and captures a close-up of the active speaker.
Cameras SpeakerTrack ConnectorDetection CameraLeft Cameras SpeakerTrack Whiteboard Mode This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected to the codec (video system). Furthermore, Cameras SpeakerTrack ConnectorDetection to the codec.
(Cisco Unified Communications Manager (CUCM) version Default value: Off 9.1.2 or newer, Cisco TelePresence Video Communication Server (VCS) version X8.1 or newer, Cisco Media Server (CMS) version 2.1 or newer). Change this setting if you want to Value space: Off/On disable the active control features.
If multiple protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the system cannot register, the auto-selection chooses H323. Value space: Off/On/BestEffort H320: All calls are set up as H.320 calls (only applicable if connected to Cisco Off: The system will not use encryption. TelePresence ISDN Link).
If registered to a Cisco TelePresence Video Communication Server (VCS), the video system Value space: Allow/Deny can use its own built-in MultiSite feature. If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM Allow: You will be notified when someone calls you while you are already in a call.
Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN Define the static IPv4 network address for the system. Applicable only when Network IPv4 clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Assignment is set to Static.
Default value: Auto Value space: Auto/Manual/Off Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is not available, VLAN is not enabled. Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.
NetworkServices CDP Mode NetworkServices HTTP Mode Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the Define whether or not to allow access to the video system using the HTTP or HTTPS (HTTP endpoint report certain statistics and device identifiers to a CDP-enabled switch. If CDP is Secure) protocols.
SNMP Agent in the codec. The default Requires user role: ADMIN password is "public". If you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP Community is configured there too. NOTE: The SNMP Default value: On Community password is case sensitive.
This setting applies to the Intelligent Proximity feature. Set the maximum volume of the In order to use Cisco Touch 10 (touch panel) as user interface for the video system, Touch ultrasound pairing message. Refer to the Peripherals Pairing Ultrasound Volume Mode 10 must be either directly connected to the video system or paired to the video system via setting.
Define the number of cameras that are expected to be connected to the video system. Define the number of Cisco Touch controllers that are expected to be connected to the This information is used by the video system's diagnostics service. If the number of video system.
CUCM: The phonebook is located on the Cisco Unified Communications Manager. Spark: The phonebook is located on Spark. TMS: The phonebook is located on the Cisco TelePresence Management Suite server. VCS: The phonebook is located on the Cisco TelePresence Video Communication Server.
Spark: Push configurations to the video system from Spark. TMS: Push configurations to the video system from TMS (Cisco TelePresence Management System). VCS: Push configurations to the video system from VCS (Cisco TelePresence Video Communication Server). Provisioning LoginName This is the username part of the credentials used to authenticate the video system with the provisioning server.
This is the password part of the credentials used to authenticate the video system with the Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager provisioning server. This setting must be used when required by the provisioning server.
In order to use a client, at least one of the Proximity services must be must be On for this setting to take any effect. enabled (refer to the Proximity Services settings). In general, Cisco recommends enabling all the Proximity services.
ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be video systems can use to discover the optimized media path. Thus the shortest route for part of a shared line.
Default value: "" Value space: Standard/Cisco Value space: String (0, 255) Standard: Use this when registering to standard SIP Proxy (tested with Cisco The preferred format is DNS SRV record (e.g. _turn._udp.<domain>), or it can be a valid TelePresence VCS and Broadsoft) IPv4 or IPv6 address.
You can customize our Touch 10 user interface to allow control of peripherals in a meeting room, for example lights and blinds. You need a Cisco video system with a Touch controller, and a You can use the In-Room Control editor This allows for the powerful combination of a control system’s...
Page 174
All images in these materials are for representational purposes only, actual products may differ. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.
Cisco website at www.cisco.com/go/offices. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/ or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners.
Need help?
Do you have a question about the TelePresence SX80 and is the answer not in the manual?
Questions and answers