Download Print this page

Advertisement

Cisco TelePresence SX80
Administrator Guide
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices
Collaboration Endpoint software version 8.0
NOVEMBER 2015
Administrator guide
for Cisco TelePresence SX80
D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015.
www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.
1

Advertisement

Chapters

   Summary of Contents for Cisco TelePresence SX80

  • Page 1

    Administrator Guide  Introduction Configuration Peripherals Maintenance System settings Appendices Collaboration Endpoint software version 8.0 NOVEMBER 2015 Administrator guide for Cisco TelePresence SX80 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 2: Table Of Contents

    System settings Appendices Table of contents Thank you for choosing Cisco! Your Cisco product has been designed to give you many years of safe, reliable operation. Introduction ........................4 User documentation and software ..................5 This part of the product documentation is aimed at administrators What’s new in CE8.0 ......................

  • Page 3

    SIP settings ........................120 Standby settings ........................124 SystemUnit settings ......................125 Time settings ........................126 UserInterface settings ....................... 129 Video settings ........................131 Experimental settings ......................141 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 4: Introduction

    Cisco TelePresence SX80 Administrator Guide  Introduction Introduction Configuration Peripherals Maintenance System settings Appendices Chapter 1 Introduction D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 5: User Documentation And Software

    ►  User documentation on the Cisco web site appendix for more information about the guides for this endpoint. Downloading the user documentation We recommend you visit the Cisco web site regularly for updated versions of the guides: ►  http://www.cisco.com/go/sx-docs Software Download software for the endpoint from the Cisco web site: ► ...

  • Page 6: What's New In Ce8.0

    Refer to the What’s New chapter in the API guide for the video system, to see the changes that are made to the public API. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 7

    TelePresence Conductor) may be used instead. • Custom video layouts and video composition using TC Console is not supported. • MediaNet is no longer supported. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 8

    Fast> Default value: Default NetworkServices Medianet Metadata NEW: <Auto / Conservative> NetworkServices MultiWay * Default value: Auto SIP AuthenticateTransferror SIP OCSP * D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 9

    Conference [1] AutoAnswer Mute PresentationLargeSpeaker /Prominent / Overlay / Single> Renamed to: Conference AutoAnswer Mute NEW: <Auto / Equal / Prominent / Overlay / Single> D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 10

    Renamed to: SIP Authentication Password Conference [1] Presentation RelayQuality SIP Profile [1] DefaultTransport Renamed to: Conference Presentation RelayQuality Renamed to: SIP DefaultTransport D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 11

    SIP Profile [1] Type Renamed to: SIP Type SIP Profile [1] URI Renamed to: SIP URI SystemUnit ContactInfo Type Renamed to: UserInterface ContactInfo Type D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 12: Sx80 At A Glance

    The codec offers a rich input and output set, flexible media engine, and support for three screens enable various use cases. Cisco offers SX80 as a single unit, and in the following integrator packages: • SX80 and Precision 40 (PrecisionHD 1080p4xS2) camera for smaller room scenarios •...

  • Page 13: Power On And Off

    LEDs flash. It may take a few minutes for the codec to start up. The system is ready for use when the Power LED lights steadily. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 14: Front Panel Leds

    Lights steady when a serious error occurs. More information about the codec’s physical interface, including the connector panel and LEDs, are described in the Physical interface guide. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 15: How To Administer The Video System

    SystemUnit Software Version More settings and status are available in the web interface than in the API. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 16

    It is mandatory to set a password for the admin user. Sign out Hover the mouse over the user name and choose Signout from the drop-down list. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 17

    Log Files Backup and Restore User Interface Screenshots System Recovery Personalization Peripherals Restart User Administration Sign In Banner Startup Scripts Security Room Types D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 18

    Depending on product and product set-up, your Touch controller may or may not display the same menus as shown in the illustration. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 19: Configuration

    Cisco TelePresence SX80 Administrator Guide  Introduction Configuration Configuration Peripherals Maintenance System settings Appendices Chapter 2 Configuration D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 20: User Administration

    Delete <user name>... and confirm when prompted. The passphrase protects the web and command line interfaces, and the Administrator settings on the Touch controller. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 21: Change The System Passphrase

    4. Click Change Passphrase to save the change. ► User administration chapter. Use the Back button to leave without making any changes. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 22: System Configuration

    The system settings are grouped in categories. Choose a category in the left pane to show the associated settings. Categories with unsaved changes are marked with an edit symbol ( D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 23: Add A Sign In Banner

    2. Click Save to activate the banner. the web interface or the command line interface. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 24: Manage The Certificates Of The Video System

    The certificates and certificate issuers in the illustration are examples. Your system has other certificates. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 25: Manage The List Of Trusted Certificate Authorities (cas)

    CA certificates on the video The entries in a new file with CA certificates system. are appended to the existing list. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 26: Set Up Secure Audit Logging

    Save for the changes to take effect. 3. Set Audit > Logging Mode ExternalSecure. Click Save for the change to take effect. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 27: Manage Pre-installed Certificates For Cucm Via Expressway Provisioning

    Refer to the ►  Manage the list of trusted certificate authorities (CAs) chapter how to update the list of trusted certificates. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 28: Set Strong Security Mode

    Confirm your choice in the dialog box that appears. The video system restarts automatically. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 29: Change The Persistency Mode

    There is more information about performing a factory reset in the ►  Factory reset the video system chapter. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 30: Delete Cucm Trust Lists

    When you change the CUCM IP address. • When you move the endpoint between CUCM clusters. • When you need to re-generate or change the CUCM certificate. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 31: Set Up Intelligent Proximity For Content Sharing

    View shared content on a mobile device Place calls and control the video system MX700, MX800 MX200 G2, MX300 G2 Wireless share from a mobile device D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 32

    MX Series and SX Series video systems, if you have switched on Proximity (ultrasound). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 33

    Services > ...) must be Enabled as well. We recommend not to use a headset, if you have switched on Proximity (ultrasound). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 34

    If you can hear audio artifacts, like humming or clipping noise, decrease the maximum ultrasound volume (Peripherals > Pairing > Ultrasound > Volume > MaxLevel). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 35: Adjust The Video Quality To Call Rate Ratio

    H.265 is preferred over H.264, and the maximum bit rate for H.265 is 3 Mbps. When the user sets a higher bit rate, the codec will still use H.265 at 3 Mbps as long as all codecs involved supports H.265. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 36: Packet Loss Resilience - Clearpath

    ClearPath, all packet loss resilience mechanisms are used in point-to-point connections (including hosted conferences). Only some of the mechanisms are supported in MultiSite conferences. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 37: Use A Custom Wallpaper

    You have to upload it anew if you want Maximum file size: 4 MByte to start using it again. The custom wallpaper is automatically activated once uploaded. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 38: Choose Ringtone

    Use the slide bar to adjust the Use the stop button (   ) to ringtone volume. end the playback. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 39: Manage Local Contacts

    Confirm your choice 2. Click Delete to remove the local in the dialog that pops up. contact. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 40: Peripherals

    Cisco TelePresence SX80 Administrator Guide  Introduction Configuration Peripherals Peripherals Maintenance System settings Appendices Chapter 3 Peripherals D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 41: Connect Monitors

    These settings can be changed if necessary, but for ease of use no configuration is required in order to use the default values. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 42

    Video > Output > Connector 3 > MonitorRole : Recorder • UserInterface > OSD > Output : Auto • UserInterface > OSD > Output D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 43: Connect Input Sources

    Audio Line inputs (Euroblock). Refer to the SX80 installation guide or the camera documentation how to connect a camera to power, Ethernet and/or camera control. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 44

    The default value is Motion for Connector 1, 2 and 5; and Sharpness for Connector 3 and 4. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 45: Set Up Speaker Tracking

    The two cameras in the assembly work together with a built-in microphone array to automatically track and show the person that speaks. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 46: Set Up The Snap To Whiteboard Feature

    He or she cannot move whiteboard. about in the room. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 47: Troubleshooting

    If the feature is correctly configured, the camera will move to a position that covers both the whiteboard and the person that is talking. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 48

    Cameras > SpeakerTrack > Whiteboard > Mode setting on the web interface to switch the Snap to Whiteboard feature On or Off. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 49: Briefing Room Set-up

    • Speakers: We recommend good quality stereo speakers placed next to the Presentation and Remote presenter displays. Briefing room blue print Discussions D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 50: Connecting Cables

    Network port 2 as illustrated, or to Network port 3. It cannot be connected to Network port 1, which is reserved for the LAN connection. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 51

    1. Tap Layout on the Touch controller. 2. Tap the thumbnail that represents the mode you want to change to. Room mode thumbnails D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 52: Real-time Communication Requirements For Displays

    Deactivate advanced audio processing, like “Virtual Surround” effects and “Dynamic Compression”, which will make any acoustic echo canceller malfunction • Change to a different HDMI input D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 53: Connect The Touch 10 Controller

    Touch 10 is successfully connected to the codec. The Ethernet connector is behind the lid at the rear of Touch 10. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 54

    Touch 10. The PoE is behind the lid at the rated Ethernet cable can be up to 100 m rear of Touch 10. (330 ft). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 55

    Ethernet with PoE: for power and Ethernet Sound bar for audio adjustment Mini-jack, 3.5 mm Audio mute Not in use (not in use) D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 56: Maintenance

    Cisco TelePresence SX80 Administrator Guide  Introduction Configuration Peripherals Maintenance Maintenance System settings Appendices Chapter 4 Maintenance D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 57: Upgrade The System Software

    (temporarily removed). CE Console is for audio and GPIO only Also note that CE software does not support the EX Series, C Series, Profile Series, and first-generation MX200 and MX300 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 58

    The video system restarts automatically after the installation. You must sign in anew in order to continue working with the web interface after the restart. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 59: Add Option Keys

    Contact your Cisco representative to repeat these steps for all keys. obtain information about available options, and how to get the required key(s). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 60: System Status

    The status shown in the illustration serve as an example. The status of your system may be different. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 61: Run Diagnostics

    Deactivate standby to wake up the system. The messages shown in the illustration serve as examples. Your system may show other information. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 62: Download Log Files

    Refresh a log file list Click the refresh button for Current logs or Historical logs to update the corresponding lists. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 63: Create A Remote Support User

    4. Cisco TAC will generate a password. The remote support user is valid for seven days, or until it is deleted. Delete remote support user Click Delete user. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 64: Backup Or Restore A Configuration

    The configuration of the video system is likely to be incomplete, due to the differences between the two software generations. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 65: Revert To The Previously Used Software Image

    Wait while the system resets. The system restarts automatically when finished. This procedure may take a few minutes. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 66: Factory Reset The Video System

    We recommend that you back up the log files and configuration of the video system before you perform a factory reset; otherwise these data will be lost. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 67

    If this happens, go back to step 1 and try again. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 68: Factory Reset The Touch 10

    If Touch 10 is connected via LAN the device must be paired to the video system anew. When successfully paired it receives Volume down a new configuration automatically from the video system. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 69: Capture User Interface Screenshots

    All captured snapshots are included in the list above the buttons. Click the screenshot ID to display the image. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 70: System Settings

    Cisco TelePresence SX80 Administrator Guide  Introduction Configuration Peripherals Maintenance System settings System settings Appendices Chapter 5 System settings D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 71: Overview Of The System Settings

    CallHistory settings ......................82 CallHistory Mode ......................... 82 Cameras settings ......................83 Cameras Camera [1..7] AssignedSerialNumber ..............83 Cameras Camera [1..7] Backlight DefaultMode ..............83 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 72

    Conference MultiStream Mode ................... 91 Network [1] IEEE8021X Password ..................100 Conference Presentation OnPlacedOnHold ............... 92 Network [1] IEEE8021X TlsVerify ..................99 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 73

    RTP settings ........................116 NetworkServices SNMP Mode ..................108 RTP Ports Range Start .......................116 NetworkServices SNMP SystemContact................108 RTP Ports Range Stop .......................116 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 74

    Video Output Connector [1..2] CEC Mode ................ 136 Standby BootAction ......................124 Video Output Connector [1..3] Location HorizontalOffset ..........136 Standby Control .........................124 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 75

    Video Selfview Default OnMonitorRole ................139 Video Selfview Default PIPPosition ................... 139 Video Selfview OnCall Duration ..................140 Video Selfview OnCall Mode .................... 139 Experimental settings ....................141 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 76: Audio Settings

    When set to InCallOnly this will prevent the audio-system from being muted by Default value: 0 mistake. Value space: Integer (-24..0) Select a value between -24 and 0, in steps of 1 dB. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 77: Audio Input Hdmi [1..3] Mode

    Mono: The Audio Line input signal is a mono signal. Right: The Audio Line input signal is the right channel of a stereo signal. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 78: How To Find The Ip Address Audio Input Line [1

    On: Echo Control is normally set to On to prevent the far end from hearing their own audio. Once selected, echo cancellation is active at all times. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 79: Audio Input Microphone [1..8] Equalizer Mode

    Line: Select Line when you have a standard balanced line input. The phantom voltage Value space: 1/2/3/4/5 and pre-amplification is Off. Select the video input connector to associate the audio source with. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 80: Audio Output Hdmi [1..2] Level

    Select a value between -24 and 0, in steps of 1 dB. Right: The Audio Line output signal is the right channel of a stereo signal. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 81: Audio Output Line [1..6] Mode

    Requires user role: ADMIN Default value: On Value space: Off/On Off: Disable the audio output line. On: Enable the audio output line. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 82: Callhistory Settings

    Value space: Off/On Off: New entries are not added to the call history. On: New entries are stored in the call history list. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 83: Cameras Settings

    Cameras Camera [n] Brightness DefaultLevel setting. Typical situations where the codec does not receive EDID information are: when you connect a Cisco TelePresence 60 camera using 3G-SDI; when you connect a Cisco TelePresence 60 (Cisco PrecisionHD 1080p4xS2) camera; when you use an HDMI repeater Cameras Camera [1..7] Brightness DefaultLevel...

  • Page 84: Cameras Camera [1

    This setting enables gamma corrections, and applies only to cameras which support gamma mode. Gamma describes the nonlinear relationship between image pixels and This setting applies only when using a Cisco TelePresence PrecisionHD 1080p12x camera. monitor brightness. If adjusting the camera position by hand you can configure whether the camera should keep its new position or return to the preset or position it had before.

  • Page 85: Cameras Camera [1

    Cameras SpeakerTrack Mode Requires user role: USER Default value: 1 This setting applies only when using a Cisco TelePresence SpeakerTrack 60 camera. The SpeakerTrack 60 camera assembly consists of two cameras and uses an audio tracking Value space: Integer (1..16) technique that finds and captures a close-up of the active speaker.

  • Page 86: Cameras Speakertrack Connectordetection Cameraleft

    Cameras SpeakerTrack TrackingMode Cameras SpeakerTrack ConnectorDetection CameraLeft This setting applies only when using a Cisco TelePresence SpeakerTrack 60 camera, and This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected when Cameras SpeakerTrack Mode is set to Auto.

  • Page 87: Cameras Speakertrack Whiteboard Mode

    System settings Appendices Cameras SpeakerTrack Whiteboard Mode This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected to the codec. Define whether to enable the Snap to Whiteboard feature or not. The Snap to Whiteboard feature relies on a speaker track camera. When a presenter is standing next to the whiteboard, the camera will capture both the presenter and the whiteboard if the Snap to Whiteboard feature is enabled.

  • Page 88: Conference Settings

    Active control is a feature that allows conference participants to administer a conference Define if the microphone shall be muted when an incoming call is automatically answered. on Cisco TelePresence Server using the video system's interfaces. Each user can see Requires that AutoAnswer Mode is switched on.

  • Page 89: Conference Defaultcall Protocol

    BestEffort: The system will use encryption whenever possible. H320: All calls are set up as H.320 calls (only applicable if connected to Cisco > In Point to point calls: If the far end system supports encryption (AES-128), the call will TelePresence ISDN Link).

  • Page 90: Conference Farendcontrol Signalcapability

    Requires user role: ADMIN Set the maximum transmit call rate (kbps). Default value: 6000 Value space: Integer (64..6000) Set the maximum transmitt call rate (kbps). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 91: Conference Incomingmultisitecall Mode

    If registered to a Cisco TelePresence Video Communication Server (VCS), the video system Conference IncomingMultisiteCall Mode can use its own built-in MultiSite feature. If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM Select whether or not to allow incoming calls when already in a call/conference.

  • Page 92: Conference Presentation Relayquality

    Requires user role: ADMIN Default value: 5 Value space: Integer (1..10) Set the bandwidth weight for the presentation channel. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 93: Facilityservice Settings

    Requires user role: ADMIN Default value: "" Value space: String (0, 1024) The name of the facility service. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 94: Gpio Settings

    InputMuteMicrophones: When the pin is activated (0 V), the microphones will be muted. When deactivated (+12 V), the microphones are unmuted. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 95: H323 Settings

    Gatekeeper: The system uses a Gatekeeper to make an H.323 call. When choosing this option, the H323 Gatekeeper Address must also be configured. Value space: String (0, 50) The authentication login name. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 96: H323 Encryption Keysize

    Requires user role: ADMIN Default value: "" Value space: String (0, 30) The H.323 Alias E.164 address. Valid characters are 0-9, * and #. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 97: H323 Nat Address

    Static: When set to Static the ports are given within a static predefined range [5555- 6555]. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 98: Logging Settings

    Requires user role: ADMIN Default value: On Value space: Off/On Off: Disable the system logging service. On: Enable the system logging service. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 99: Network Settings

    Requires user role: ADMIN Default value: Off Value space: Off/On Off: The 802.1X authentication is disabled (default). On: The 802.1X authentication is enabled. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 100: Network [1] Ieee8021x Anonymousidentity

    Requires user role: ADMIN Default value: On Value space: Off/On Off: The EAP-TLS protocol is disabled. On: The EAP-TLS protocol is enabled (default). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 101: Network [1] Ieee8021x Eap Peap

    Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN Define the static IPv4 network address for the system. Applicable only when Network IPv4 clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Assignment is set to Static.

  • Page 102: Network [1] Ipv6 Address

    Signalling, Network QoS Diffserv ICMPv6 and Network QoS Diffserv NTP settings are Default value: "" used to prioritize packets. Value space: String (0, 64) A valid IPv6 address. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 103: Network [1] Qos Diffserv Audio

    Set the priority of the signalling packets in the IP network - the higher the number, the higher the priority. The default value is 0 (best effort). higher the priority. The default value is 0 (best effort). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 104: Network [1] Qos Diffserv Icmpv6

    Set the priority of the NTP packets in the IP network - the higher the number, the higher the priority. The default value is 0 (best effort). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 105: Network [1] Trafficcontrol Mode

    Default value: Auto Value space: Auto/Manual/Off Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is not available, VLAN is not enabled. Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.

  • Page 106: Networkservices Settings

    NetworkServices CDP Mode NetworkServices HTTP Mode Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the Define whether or not to allow access to the video system using the HTTP or HTTPS (HTTP endpoint report certain statistics and device identifiers to a CDP-enabled switch. If CDP is Secure) protocols.

  • Page 107: Networkservices Https Ocsp Mode

    Off: Disable the possibility to place and receive SIP calls. A valid URL. On: Enable the possibility to place and receive SIP calls (default). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 108: Networkservices Snmp Systemlocation

    These password is "public". If you have the Cisco TelePresence Management Suite (TMS) you variables can then be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by must make sure the same SNMP Community is configured there too.

  • Page 109: Networkservices Ssh Allowpublickey

    Off: The Telnet protocol is disabled. This is the factory setting. Range: Select a value between 0 and 3600 seconds. On: The Telnet protocol is enabled. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 110: Networkservices Welcometext

    Requires user role: ADMIN Default value: On Value space: Off/On Off: The XML API is disabled. On: The XML API is enabled (default). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 111: Peripherals Settings

    Peripherals Pairing CiscoTouchPanels RemotePairing Peripherals Pairing Ultrasound Volume MaxLevel In order to use Cisco Touch 10 (touch panel) as user interface for the video system, Touch This setting applies to the Intelligent Proximity feature. Set the maximum volume of the 10 must be either directly connected to the video system or paired to the video system via ultrasound pairing message.

  • Page 112: Phonebook Settings

    Off: Do not use a phonebook. VCS: The phonebook is located on the Cisco TelePresence Video Communication Server. TMS: The phonebook is located on the Cisco TelePresence Management Suite server. CUCM: The phonebook is located on the Cisco Unified Communications Manager. Phonebook Server [1] URL Define the address (URL) to the external phone book server.

  • Page 113: Provisioning Settings

    TMS: Push configurations to the video system from TMS (Cisco TelePresence Management System). GET: Select GET when the provisioning server supports GET. VCS: Push configurations to the video system from VCS (Cisco TelePresence Video POST: Select POST when the provisioning server supports POST. Communication Server).

  • Page 114: Provisioning Externalmanager Address

    External Manager address. Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager Requires user role: ADMIN (CUCM) and an alternate CUCM is available for redundancy. Define the address of the alternate CUCM.

  • Page 115: Proximity Settings

    In order to use a client, at least one of the Proximity services must be must be On for this setting to take any effect. enabled (refer to the Proximity Services settings). In general, Cisco recommends enabling all the Proximity services.

  • Page 116: Rtp Settings

    NOTE: Restart the system for any change to this setting to take effect. Requires user role: ADMIN Default value: 2486 Value space: Integer (1120..65535) Set the last port in the range of RTP ports. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 117: Security Settings

    This setting is only relevant when Security Audit Logging Mode is set to External or ExternalSecure. Requires user role: AUDIT Default value: "" Value space: String (0, 64) A valid IPv4 address or IPv6 address D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 118: Security Audit Server Port

    Default value: 0 Value space: Integer (0..10000) Set the inactivity timeout (seconds); or select 0 when inactivity should not enforce automatic logout. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 119: Serialport Settings

    Off: The user can access the codec via the serial port without any login. On: Login is required when connecting to the codec via the serial port. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 120: Sip Settings

    This is the password part of the credentials used to authenticate towards the SIP proxy. Requires user role: ADMIN Default value: "" Value space: String (0, 128) A valid password. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 121: Sip Ice Defaultcandidate

    ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be endpoints can use to discover the optimized media path. Thus the shortest route for audio part of a shared line.

  • Page 122: Sip Preferredipmedia

    Not applicable in this version. Requires user role: ADMIN Default value: "" Value space: String (0, 255) A valid IPv4 address, IPv6 address or DNS name. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 123: Sip Turn Droprflx

    IP address. Value space: Standard/Cisco Requires user role: ADMIN Standard: Use this when registering to standard SIP Proxy (tested with Cisco TelePresence VCS and Broadsoft) Default value: ""...

  • Page 124: Standby Delay

    RestoreCameraPosition: When the video system restarts, the camera returns to the position that it had before the restart. DefaultCameraPosition: When the video system restarts, the camera moves to the factory default position. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 125: Systemunit Settings

    SNMP Agent. Requires user role: ADMIN Default value: "" Value space: String (0, 50) Define the system name. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 126: Time Settings

    DD_MM_YY: The date January 30th 2010 will be displayed: 30.01.10 MM_DD_YY: The date January 30th 2010 will be displayed: 01.30.10 YY_MM_DD: The date January 30th 2010 will be displayed: 10.01.30 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 127: Time Zone

    Menominee, America/Merida, America/Metlakatla, America/Mexico_City, America/ GMT+6, Etc/GMT+7, Etc/GMT+8, Etc/GMT+9, Etc/GMT-0, Etc/GMT-1, Etc/GMT-10, Etc/ Miquelon, America/Moncton, America/Monterrey, America/Montevideo, America/Montreal, GMT-11, Etc/GMT-12, Etc/GMT-13, Etc/GMT-14, Etc/GMT-2, Etc/GMT-3, Etc/GMT-4, Etc/ D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 128

    Central, US/East-Indiana, US/Eastern, US/Hawaii, US/Indiana-Starke, US/Michigan, US/ Mountain, US/Pacific, US/Pacific-New, US/Samoa, UTC, Universal, W-SU, WET, Zulu> Select a time zone from the list. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 129: Userinterface Settings

    Default value: On Value space: Off/On Off: There is no key tone sound effect. On: The key tone sound effect is turned on. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 130: Userinterface Osd Output

    Custom: Use the custom wallpaper as background image on the screen. If no custom wallpaper is uploaded to the system, the setting will revert to the default value. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 131: Video Settings

    LowerLeft: The active speaker PiP will appear in the lower left corner of the screen. switched. LowerRight: The active speaker PiP will appear in the lower right corner of the screen. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 132: Video Defaultlayoutfamily Remote

    Define which video input source shall be used as the main video source. Requires user role: USER Default value: 1 Value space: 1/2/3/4 Set the source to be used as the main video source. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 133: Video Input Connector [1

    Sharpness: Gives the highest possible resolution. Used when you want the highest quality of detailed images and graphics. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 134: Video Input Connector [1..5] Optimaldefinition Profile

    Medium: Requires good and stable lighting conditions and a good quality video input. For mode. some call rates this leads to higher resolution. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 135: Video Input Connector [1

    IfSignal: When set to IfSignal, the menu selection for the video input connector will only be visible when something is connected to the video input. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 136: Video Output Connector [1..2] Cec Mode

    Default value: Connector [1]: -1 Connector [2]: 0 Connector [3]: 1 Value space: Integer (-100..100) Range: The value must be between -100 and 100. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 137: Video Output Connector [1

    1920_1200_50: The resolution is 1920 x 1200, and the refresh rate is 50 Hz. 1920_1200_60: The resolution is 1920 x 1200, and the refresh rate is 60 Hz. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 138: Video Output Connector [1

    LowerLeft: The presentation PiP will appear in the lower left corner of the screen. LowerRight: The presentation PiP will appear in the lower right corner of the screen. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 139: Video Selfview Default Fullscreenmode

    [n] MonitorRole set to Third. Current: When leaving a call, the self-view picture will be kept on the same output as it was during the call. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 140: Video Selfview Oncall Duration

    Default value: 10 Value space: Integer (1..60) Range: Choose for how long self-view remains on. The valid range is between 1 and 60 seconds. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 141: Experimental Settings

    Experimental settings The Experimental settings are for testing only and should not be used unless agreed with Cisco. These settings are not documented and WILL change in later releases. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 142: Appendices

    Cisco TelePresence SX80 Administrator Guide  Introduction Configuration Peripherals Maintenance System settings Appendices Appendices Appendices D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 143: How To Use Touch 10

    Messages to invoke the Share to start sharing content voice mail system, if available. and to conduct presentations. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 144: Set Up Remote Monitoring

    SCREEN. IT IS YOUR RESPONSIBILITY TO COMPLY WITH PRIVACY REGULATIONS WHEN USING THE SYSTEM AND CISCO DISCLAIMS ALL LIABILITY FOR ANY UNLAWFUL USE OF THIS FEATURE. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 145: Access Call Information While Using The Web Interface

    Answer the call automatically. Disconnect the call Open the Call Control page Click Open Call Control to go straight to the Call Control page. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 146: Place A Call Using The Web Interface

    To disconnect just one participant in a conference, click When searching, matching entries from the Local, Directory and Recents lists button for that participant. will be listed as you type. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 147: Calling More Than One

    Microphone: On to mute the microphone. Then the text changes to Microphone: Off. Click Microphone: Off to unmute. Volume down Volume up D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 148: Share Content Using The Web Interface

    Shows snapshots of the selected presentation source. Only available on video systems that have the Remote Monitoring option. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 149: Local Layout Control

    The set of layouts to choose from depends on the system configurations. You may change the layout both when idle and in a call. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 150: Control The Local Camera(s)

    Only relevant controls appear in the window. You cannot use the web interface to define a preset; you should use the Touch controller. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 151: Control The Far End Camera

    If you are not allowed to control the far end camera, the controls will not appear in the image. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 152: Advanced Customization Of Audio And Gpio

    How to obtain the CE Console application Download the CE Console application for free from the Cisco DevNet web site. Go to: ► http://developer.cisco.com/web/telepresence-developer D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 153: Access The Video System's Xml Files

    API. • Valuespace.xml contains an overview of all the value spaces of system settings, status information, and commands. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 154: Execute Api Commands And Configurations From The Web Interface

    1. Enter a command (xCommand or xConfiguration), or a sequence of commands, in the text area. 2. Click Execute to issue the command(s). D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 155: Manage Startup Scripts

    Delete a startup script 5. Click to activate the startup 1. Select the startup script from the list. script. 2. Click Delete. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 156: Serial Interface (rs-232)

    SerialPort > BaudRate Restart the video system when you have made changes to the serial port settings. D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 157: Technical Specification

    • 1920 × 1080@25 Hz (1080p25) • 1280 × 768@60 Hz (WXGA) • 1920 × 1080@24, and 23.97 Hz (1080p24) HDMI version 1.4 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 158

    • Auto gatekeeper discovery • Disable IP services • Dynamic playout and lip-sync buffering • Network settings protection • H.245 DTMF tones in H.323 D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 159

    All images in these materials are for representational purposes only, actual products may differ. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.

  • Page 160: Supported Rfcs

    RFC 4587 RTP Payload Format for H.261 Video Streams for SDP • RFC 4629 RTP Payload Format for ITU-T Rec. H.263 • RFC 3891 The SIP “Replaces” Header D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 161: User Documentation On The Cisco Web Site

    LEDs. Reference Guides | Command references • API reference guides: Reference guide for the Application Programmer Interface (API) D15328.01 SX80 Administrator Guide CE8.0, NOVEMBER 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.

  • Page 162: Cisco Contacts

    Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/ trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

Comments to this Manuals

Symbols: 0
Latest comments: