Primex XR Series Installation Manual
Analog clock
Hide thumbs
Also See for XR Series:
- Install manual (43 pages) ,
- Install & user's manual (32 pages) ,
- Troubleshooting manual (30 pages)
Related Manuals for Primex XR Series
Summary of Contents for Primex XR Series
- Page 1 XR T YNCHORNIZATION XR S ERIES NALOG LOCK NSTALLATION UIDE Doc Part No.: 140108 11.16.16...
-
Page 2: Primex Wireless Locations
Legal Notice Copyright ©2016 Primex Wireless, Inc. All rights reserved. U.S. Patents 6,873,573; 7,352,657. Other Patents Pending. Printed in the USA. Information in this document is subject to change without notice. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical or otherwise, for any purpose, without the prior written permission of Primex Wireless. -
Page 3: Table Of Contents
16" Dual-Sided Analog Clock Installation Dual-Sided Metal Series Analog Clock Installation Remote Antenna Analog Clock Installation Instructions Water Resistant Analog Clock Installation Remove a Clock Lock-Mounted Analog Clock Remove a Clock from a Dual-mount Bracket Primex Wireless XR Series Analog Clock Installation Guide... - Page 4 Support Warranty Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 5: About This Guide
BOUT THIS UIDE Purpose This guide is intended to provide the instructions and information required to install and operate Primex Wireless XR Series Analog Clock. Typographical Conventions This guide includes notes, cautions, and warnings content that highlights important messages. Typeface Indicates Indicates something important or useful. -
Page 6: Regulatory Compliance
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 7: Important Safety Instructions
AC power must be supplied from a circuit that has a resettable circuit breaker. AC mains power supply must be disconnected while installing or performing maintenance of any device. Open the circuit breaker supplying the device before attempting installation, maintenance, or repairs. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 8: Automatic Setting Analog Clock Set Up And Operation
An automatic setting model only has a button on the back of the clock. NOTE: An electric-powered clock does not require a set up procedure to receive its time from the system transmitter. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 9: Set Up Automatic Setting Analog Clock (Battery-Operated)
12 o'clock position and remain there indefinitely. To make the hands move again, wait until they have stopped, then press and hold the button again. The clock will enter its normal setup procedure and set itself. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 10: Battery Operated Models Maintenance And Requirements
The use of heavy duty and zinc carbon batteries is NOT recommended as they have a shorter life span and have risk of leakage if over discharged. Do NOT use rechargeable NiCad batteries as their output voltage is too low to assure proper operation Do NOT use standard lithium batteries Primex Wireless XR Series Analog Clock Installation Guide... -
Page 11: Replace Batteries - Automatic Setting Analog Clock
Every day at midnight, the clock checks to ensure that the position of the hands are correct and will automatically correct the hands if they are off. This resetting of the hands is the same as the Hand Alignment Check and Self Initialization procedure. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 12: Reset Clock
P AND PERATION Operation of a battery-operated analog clock for use with Primex Wireless XR Time Synchronization system requires initial set up to receive its time from the system transmitter. A manual setting model has both a button and a grey set wheel on the back of the clock. -
Page 13: Manual Setting Analog Clock Set Up (Battery-Operated)
Clocks will work in these marginal signal areas but may have a battery life shorter than five years. Estimated battery life in a marginal area is four years. To reset the initial setup, simply remove the batteries then repeat the Manual Set Clock set up procedure. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 14: Automatic Daily Transmitter Signal Check - Manual Setting Analog Clock
(which does not move during the setting procedure). For example, if the second hand is pointing to the “6”, then the minute hand should be halfway between minute marks. If the second hand is at the “12”, then the minute hand should be placed on the minute mark. Primex Wireless XR Series Analog Clock Installation Guide... - Page 15 Once the clock has decoded a valid time signal from the transmitter, the clock will beep and continue to beep with every valid decoded signal for the next minute. Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 16: Install Analog Clock
Manual Setting Analog Clock Models: Verify the set up procedure is completed before the clock is installed. Any damage to the clock due to improper wiring voids the warranty. It is at Primex Wireless discretion as to whether damage to the clock was caused by improper wiring. -
Page 17: Apply Power - Battery Operated Models
NOTE: It is important to insert the batteries with the battery ‘+’ end to ‘+’ end of the battery holder to achieve proper battery orientation. Figure 1: Back of Battery-Operated Analog Clock Primex Wireless XR Series Analog Clock Installation Guide... -
Page 18: Apply Power - Electric Analog Clock Installation
120V~ power line in a junction box installed by a licensed electrician. Leave a minimum of 6 in. (15 cm) of cord inside the junction box. To conform to UL and National Building Code, the use of the clock-lock feature is required for this configuration. Primex Wireless XR Series Analog Clock Installation Guide... - Page 19 Cord Specification Line Neutral Ground (earth) 21mA Yellow 24 VAC 18 in. (45.7 cm) Yellow pigtail/hardwired 25mA Black Green 120 VAC 18 in. (45.7 cm) White standard non- polarized two- prong plug. Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 20: Single-Sided Analog Clock Installation
12 o’clock position and remain there indefinitely. To release the hands from an indefinite position, press and release the button again. The clock will automatically initiate the Self Initialization procedure and set itself. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 21: 12" Dual-Sided Electric Analog Clock Installation
Lift the power cord out of the way, then slide the bracket cover back onto the dual mount bracket. Primex Wireless XR Series Analog Clock Installation Guide... - Page 22 5. Route the power cords as desired and apply AC power. The clocks set to the correct time after they receive a valid time signal from the system transmitter. Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 23: 12" Dual-Sided Battery Analog Clock Installation
3. Slide the dual clock bracket over the four tabs on the mounting plate. A tap with a rubber mallet on the clock bracket may be required to seat the clock bracket assembly fully into place. Primex Wireless XR Series Analog Clock Installation Guide... -
Page 24: 16" Dual-Sided Analog Clock Installation
A 16" Dual-Sided Analog Clock consists of two analog clocks and a Dual Clock Kit. Using the kit you combine two clocks to create a dual-sided clock, which can be either ceiling or wall mounted. Primex Wireless XR Series Analog Clock Installation Guide... - Page 25 2. Fasten a supplied #6 x 1/2" long screw to each mounting post located on the backside of each clock, leaving a 1/8 to 3/16 in. gap between the screw head and mounting post. Primex Wireless XR Series Analog Clock Installation Guide...
- Page 26 4. For each clock - place clock into the bracket housing with the 10/11 and 4/5 numerals over the clock-lock tab and rotate clock clockwise to lock into place. The screws fastened to the clock mounting posts lock into the housing clock-lock tabs. Primex Wireless XR Series Analog Clock Installation Guide...
- Page 27 6. Examine the mounting plate to ensure the bracket is fully engaged. The small hole in top side of the mounting plate should be visible and fully exposed. To increase the security of the clock assembly, a common screw may be inserted into the hole and screwed into the wall. Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 28: Dual-Sided Metal Series Analog Clock Installation
5. Align one of the posts on the back of the clock with the appropriate post in the bracket, next to a clip. Make sure that the raised portion of the clip next to the post is inside the bracket. Primex Wireless XR Series Analog Clock Installation Guide... - Page 29 9. Taking the fully assembled dual clock, line up the base (stem) of the clock with the plate that is mounted on the wall. Slip the keyhole slots on the back of the base over the posts on the plate and push the clock down to secure. Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 30: Remote Antenna Analog Clock Installation Instructions
Installation Steps Complete the steps below to install a remote antenna analog clock. Refer to Figure 5 for the illustration of the clock components, as referenced in the steps below. Primex Wireless XR Series Analog Clock Installation Guide... - Page 31 4. For vertical mounting, connect antenna (7) to the other end of connector (5). For horizontal mounting, connect antenna (7) to the right angle connector (6). 5. Use two screws (4) to secure bracket (3). Figure 5: Remote Antenna Analog Clock Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 32: Water Resistant Analog Clock Installation
O-ring voids the manufacturer warranty. 2. From the back of the clock, remove the parts from the supplied hardware kit. 3. From the back of the clock, remove and discard the two spacers. Primex Wireless XR Series Analog Clock Installation Guide... - Page 33 6. (Optional) Apply the supplied lubricant to the O-ring or to the inner side of the clock case. Align the clock face as desired and press the clock into the bracket; approximately 3/16" away from the wall.To remove the clock, insert and turn a wide standard screwdriver in the removal slots. Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 34: Remove A Clock Lock-Mounted Analog Clock
#4 3/8" self tapping screws for securing the clock. Remove a Clock Lock-Mounted Analog Clock Follow the illustrated steps below to remove an analog clock from a clock-lock mount. Primex Wireless XR Series Analog Clock Installation Guide... - Page 35 Primex Wireless XR Series Analog Clock Installation Guide...
-
Page 36: Remove A Clock From A Dual-Mount Bracket
1. Place clock in the housing with the 10/11 and 4/5 numerals over the brass posts. 2. Place your hands at the 10/11 and 4/5 positions and turn the clock clockwise to lock into place. Primex Wireless XR Series Analog Clock Installation Guide... - Page 37 UPPORT Supporting Documentation To obtain additional technical documentation for Primex Wireless products, visit the Support area on our Web site (www.primexwireless.com). Primex Wireless Technical Support Technical Support responds to specific questions about product features, system configuration, and troubleshooting. All support services will be delivered in accordance with your organization's support agreement and warranties.
- Page 38 Primex Corporation warrants this product to be free from defects in materials and workmanship for a standard of one year from the date of purchase. Primex will at its sole option, repair or replace any components that fail in normal use. Such repairs or replacements will be made at no charge to the customer for replacement parts.