Related Manuals for Primex XR Classic Series
Summary of Contents for Primex XR Classic Series
- Page 1 XR T YNCHORNIZATION XR C LASSIC ERIES IGITAL LOCKS IMERS NSTALLATION UIDE Doc Part No.: 140109 04.09.14...
- Page 2 Legal Notice Copyright ©2014 Primex Wireless, Inc. All rights reserved. U.S. Patents 6,873,573; 7,352,657. Other Patents Pending. Printed in the USA. Information in this document is subject to change without notice. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical or otherwise, for any purpose, without the prior written permission of Primex Wireless.
-
Page 3: Table Of Contents
Set Display to 24-Hour Time - XR Classic Series Set PM /Indicator - XR Classic Series Set Offset Hours - XR Classic Series Set Audible Buzzer (Timer Models Only) - XR Classic Series Set Receive Channel (Programmable Timer Only) - XR Classic Series Install Classic Series Digital Clock/Timer... - Page 4 Normal State - Timer Mode Set State - Timer Mode Code Blue Count Mode Digital Programable Timer Operation Support Warranty Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 5: Regulatory Compliance
This device complies with part 15 of the FCC rules as well as with Industry Canada. Operation of this device is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 6: Important Safety Instructions
AC power must be supplied from a circuit that has a resettable circuit breaker. AC mains power supply must be disconnected while installing or performing maintenance of any device. Open the circuit breaker supplying the device before attempting installation, maintenance, or repairs. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 7: Digital Clock And Timer Specifications
Power Outage Memory < -110dBm Receiver Sensitivity (Decode) SNS and XR Classic Series models: 120 VAC/ 50–60 cycle, with either 9' (2.74 cm) cord with Power Supply plug or18" (45.72 cm) cord with pigtail 24VAC models only: 24 VAC - 50–60 cycle, with 18" (45.72 cm) cord with pigtail 230 VAC - 50-60 cycle, 2 m cord (including plug);... -
Page 8: Digital Timer Features
The count-down timer can count down from a preset time to 00:00:00. The decimal point on the far right (near the minutes/seconds digits) lights up to indicate down counter function. The user can preset count-down start time. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 9 Switch control can simultaneously activate two connected timers for even more accurate time management Buttons are cleanable with water and most common disinfectants. Be sure to test any cleaning solutions on a small area Figure 1: Timer Switch Control Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 10: Configure Digital Clock And Timer Settings - Classic Series
72 hours, the red colon on the clock will flash. Set LED Dimmer Display - XR Classic Series NOTE: The LED Display is set to 100% by factory default. -
Page 11: Set Alternating Time/Date - Xr Classic Series
The clock reads the hour offset on start up, when the RESET button is pushed, and each time the clock receives data from the transmitter for the offset hours to go into effect. Set Audible Buzzer (Timer Models Only) - XR Classic Series The audible buzzer is only on the count-up and count-down timer function. To enable the buzzer feature, place the OPTIONS - Buzzer switch (8) in the up position, as illustrated below. -
Page 12: Set Receive Channel (Programmable Timer Only) - Xr Classic Series
Figure 8: Audible Buzzer Set Receive Channel (Programmable Timer Only) - XR Classic Series The Programmable Countdown Timer receives its time and schedule information from a transmitter into which a schedule was downloaded. To select a transmitter, set the RF Channel Switch to the corresponding transmitter channel number, per the specifications below. -
Page 13: Install Classic Series Digital Clock/Timer
Verify the clock's settings have been configured before the clock is installed. Any damage to the clock due to improper wiring voids the warranty. It is at Primex Wireless discretion as to whether damage to the clock was caused by improper wiring. -
Page 14: 230 Vac Wiring Specifications
NOTE: Most building codes prohibit the use of hard-wired power connections for devices that can be removed without tools. Clock/timers mounted directly to a wall must have standard power plugs. Figure 10: Surface Mount Illustration Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 15 Figure 11: Surface Mount Illustration Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 16: Surface-Mount Wall Bracket Installation
120V~ pigtail. If a junction box is present, the tilt bracket also has mounting holes spaced to allow direct attachment of the tilt bracket to the cover plate screw holes on the junction box. Figure 12: Tilt Bracket Mount Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 17 Figure 13: Tilt Bracket Mount 2 Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 18: Digital Clock/Timer Surface-Mount Dimension Specifications - Classic Series
18" (45.72cm) 3" (7.62cm) digit 4" (10.16 cm), 6- 7.31 lbs (3.3 kg) 260 mA 8.0" (20.32 cm) 23.25" (59.05cm) 3" (7.62cm) digit Figure 14: 2.5" x 6 Digit Back View Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 19: Surface-Mount Tilt Bracket Mounting Dimensions
8.0” 3.0” 0.4 – 0.9” 12.0” 4” 4-digit 18.0” 14” 4.0” 8.0” 3.0” 0.4 – 0.9” 12.0” 4” 6-digit 23.3” 14” 4.0” 6.3” 0.3” 0.5 – 1.0” 2.5” 6-digit 17.0” flush-mount Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 20 Dimension Clock/Timer Model 4.3” 8.0” 4° bracket 8.8” 2.5” (2.5”) 7.8” 12.0” 4° bracket 17.8” 4.0” (4”) 4.3” 9.5” 18° bracket 10.6” 2.5” (2.5”) Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 21: Remove Surface-Mount Clock/Timer With Wall Bracket
3. For vertical mounting, connect antenna #7 to the other end of connector #5. For horizontal mounting, connect antenna #7 to right angle connector #6. 4. Use two screws (Items #4) to secure bracket #3. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 22: Dual-Mount Digital Clock/Timer Installation
2. Attach the flange to the wall or ceiling using the toggle anchors and the longer machine screws provided. NOTE: If wall mounting to location outside of the junction box, break off or cut openings in flange to route power cords. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 23 5. Wire clocks to main power, using cord retaining clips to dress wires. 6. Align the clock to the bracket hooks and hinges and snap into place. Figure 17: Dual Digital Bracket Kit Flange Dimension Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
- Page 24 Figure 18: Dual Digital Clock Mounting Illustration Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
- Page 25 7.5” (19.05 cm) Dual 4” 6-digit 11.0” (27.94 cm) clock *4” 6-digit clock is not available as wall mount. Figure 19: Dual-Sided Digital Clock Dimension (A) Figure 20: Dual-Sided Digital Clock Dimension (B) Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 26: Remove Dual-Sided Digital Clock From Mounting Bracket
1. Cut a hole in the wall surface that is 5.4” (13.71 cm) x 14.4” (36.57 cm) between two studs. For Power over Ethernet (PoE) models only, proceed to step 16 (steps 2 through 15 are not required for PoE models). Figure 22: Flush-mount Wall Opening Dimensions Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 27 2x4. Figure 25: Flush-mount Timer Junction Box Specification 4. Remove the clock face plate and set aside. 5. Remove the four screws that secure the circuit board. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
- Page 28 8. For timer models only, route the timer input wires (B) through the back of the clock. Figure 28: Route Wires 9. Wire the AC power. 10. For timer models only, wire the timer input as specified below. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
- Page 29 12. Install drywall anchors (not supplied) to align with the four fastening holes located on the front of the clock assembly. 13. Mount the clock assembly to the junction box(es), using the screws supplied with the junction box and the #8 washers (supplied). Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 30: Timer Control Switch Installation
RED wire is positive and the BLACK wire is ground. Code Blue start/stop events are triggered by the application of voltage across the code blue input wires. Figure 31: Timer Control Switch Wiring Specifications Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... - Page 31 NOTE: The switch buttons and wall plate cover may be cleaned with water and/or most common disinfectant. Be sure to test any cleaning solutions on a small area before using it on the entire switch. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide...
-
Page 32: Digital Code Blue Timer And Elapsed Timer Operation
Table 5: Normal State Operation Display Specifications Clock Mode Count-Up Mode Count-Down Mode LED Display 10:45 02 0.0:00 00 99:59 59. Displays current time Decimal lit after the 10hr digit Decimal lit after the 1 sec digit Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 33: Set State - Timer Mode
The text labeled on the bottom of the switch control button is applicable (SET/CHANGE, INCREMENT, EXIT). The dash, colon, and decimal points are not displayed. The digit that is currently being set will flash. Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 34: Code Blue Count Mode
The Programmable Countdown Timer counts down in minutes and seconds at a predefined schedule of timed events from 1 minute to 99 minutes 59 seconds. The countdown schedule and events are configured and managed using the Primex Wireless Event Scheduler Pro Software and the schedule is downloaded to the system transmitter. For details on using the software, please see the Event Scheduler Pro User Guide. - Page 35 The timer will begin counting down at each preset time on schedule. When each countdown function is complete the timer automatically displays the correct time, synchronized to every other clock on your Primex Wireless XR 72MHz/GPS system. The Programmable Countdown Timer functions in much the same way as a standard digital clock.
-
Page 36: Support
Troubleshooting performed before contacting Primex Wireless Recent network changes (SNS products only) Technical Support (800) 404-8112 Telephone techsupport@primexinc.com Email (262) 248-0061 7:00 am to 7:00 pm CST | Monday through Friday Hours www.primexwireless.com Primex Wireless XR Classic Series Digital Clock/Timers Installation Guide... -
Page 37: Warranty
Primex Corporation warrants this product to be free from defects in materials and workmanship for a standard of one year from the date of purchase. Primex will at its sole option, repair or replace any components that fail in normal use. Such repairs or replacements will be made at no charge to the customer for replacement parts.