Section 9: User Access Codes; General Information; User Codes & Levels Of Authority - Honeywell VISTA-128BP Installation And Setup Manual

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

General Information

The VISTA-128BP allows a total of 150 security access
codes to be allocated. The VISTA-250BP allows a total
of 250 security access codes to be allocated. Each
security access code is identified by a user ID number.
Regardless of the number of partitions each code
has access to, it occupies only one user slot in the
system. If a code is not used in all partitions,
that user ID number cannot be used again.
The Quick Arm feature can also be programmed
(partition-specific program field *29). The Quick Arm
feature allows the user to arm the system by pressing
the [#] key instead of the security code. The security
code must always be entered to disarm the system.
User Codes & Levels of Authority
Each user of the system can be assigned a level of
authority, which authorizes the user for certain system
functions. A user can have different levels of authority
within different partitions
Level 0: Installer (User 1) Code
•
Programmed in field *00 (default = 4-1-4-0).
Installer Open/Close reporting selected in field *39.
•
Can perform all system functions (arm, disarm,
bypass, etc.), but cannot disarm if armed by
another code (or by Quick Arm).
•
Can add, delete, or change all other codes, and can
select Open/Close reports for any user.
•
Is the only code that can be used to enter program
mode. The Installer Code can be prevented from re-
entering the Program Mode by exiting using ∗98.
•
Must program at least one Master Code during
initial installation. Master Codes are codes intended
for use by the primary user(s) of the system.
Level 1: Master Codes
•
Can perform all normal system functions.
•
Can be used to assign up to 148 lower-level codes,
which can be used by other users of the system.
•
Cannot assign anybody a level of 0 or 1.
•
May change his own code.
•
Can add, delete, or change Manager or Operator
Codes. Each user's code can be individually
eliminated or changed at any time.
•
Open/Close reporting is automatically the same as
that of the Master who is adding the new user.
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM
User Access Codes
• A user code other than the installer code
must be programmed in order for the Quick
Arm feature to function.
• Users 001-050 are the only users that can
perform panel linking and are automatically
assigned panel linking access.
The system is shipped with the following defaults
for the user codes:
User 4-Digit Code
User 1 (Installer) 4140
User 2 1234
Use the "View Capabilities" keypad function (User
Code + [✳] + [✳]) to view the partitions and authority
levels for which a particular user is authorized. These
levels are described below.
Level 2: Manager Codes
•
Can perform all system functions (arm, disarm,
bypass, etc.) programmed by Master.
•
May add, delete, or change other users of the
system below this level (Manager cannot assign
anybody a level of 0, 1, or 2).
•
May change his own code.
•
Open/Close reporting is automatically the same as
that of the Manager who is adding the new user.
Levels 3-5: Operator Codes
•
Can operate a partition, but cannot add or modify
any user code (see table below).
Level Title Functions Permitted
3 Operator A Arm, Disarm, Bypass
4 Operator B Arm, Disarm
5 Operator C Arm, Disarm only if armed with
same code
•
Operator C (sometimes known as the Babysitter
Code) cannot disarm the system unless the
system was armed with that code. This code is
usually assigned to persons who may need to arm
and disarm the system at specific times only (e.g.,
a babysitter needs to control the system only when
babysitting).
S E C T I O N
Alpha Descriptor
INSTLR
MASTER
9
9-1