Zone Number Designations - Honeywell VISTA-128BP Installation And Setup Manual

VISTA-128BP/VISTA-250BP Installation and Setup Guide
Following is a list of commands used while in the Menu Mode:
#93 Enters Menu Mode.
[✳] Serves as [ENTER] key. Press to have keypad accept entry.
[#] Backs up to previous screen.
0 Press to answer NO.
1
Press to answer YES.
Quits Menu Mode and goes back to Data Field Programming Mode, if entered at first prompt of each main menu option.
00, or 000+[✳]

Zone Number Designations

The VISTA-128BP supports up to 128 zones, the
VISTA-250BP supports up to 250 zones, of hardwire,
polling loop and/or wireless protection, distributed
among up to 8 partitions. The following table lists the
zone numbers and the types of sensors that can be
used with each, and some alternate functions of the
zones.
Zone Function
1 2-wire Smoke Detectors (if used)
5 Audio Alarm Verification (if used)
7 Keyswitch (if used)
8 Latching-Type Glassbreak Detectors (if used)
1-9 Traditional Hardwired Zones
9 RS232 Input (if used)
1-250 5800 Series Wireless Devices
10-250 Polling Loop Devices
✳ + 1 Panic
995
996 # + 3 Panic
✳ + # Panic
999
Zone Defaults
Zone # Zone Type
001 09
002 03
003 03
004** 04
005 03
006 03
007 03
008 03
009 03
010–250 00
NOTES:
* Zone 992 is the Duress zone. Programming of the zone
response type is not applicable. This zone requires only the
report code programming.
** Zone 004 is also defaulted with Auto-STAY enabled.
4-4
WWW.DIYALARMFORUM.COM
#93 Menu Mode Programming Commands
Zone # Zone Type
601-632 00
800-830 00
970 00
988 00
990 00
992* N/A
995 00
996 00
997 05
999 06
WWW.DIYALARMFORUM.COM
Zone Index
The zones are designated as follows:
ZONE # ZONE
RANGE FUNCTION
001 – 250 Protection
zones
601 – 632 Relay
Supervisory
Zones
800 – 830 ECP Device
Supervisory
Zones
970, 988, System
990, & 997 Supervisory
Zones
992, 995 – Duress and
999 Keypad
Panics
Program supervisory zones with response type of 05.
Communication Defaults
*45 PRIMARY FORMAT
*46 LOW SPEED FORMAT (Prim)
*47 SECONDARY FORMAT
*48 LOW SPEED FORMAT (Sec.)
*49 CHECKSUM VERIFICATION
No checksum
*50 SESCOA/RADIONICS SEL.
*51 DUAL REPORTING
*52 STANDARD/EXPANDED REPORT FOR PRIMARY
[0] [0] [0]
Alarm Rstr Bypass
*53 STANDARD/EXPANDED REPORT FOR SECONDARY
[0] [0] [0]
Alarm Rstr Bypass
ACTUAL ZONE
As indicated
6 + 2-digit Relay Number; e.g.,
Relay Number 03 is zone 603.
8 + 2-digit Device Address; e.g.,
Device Address 01 is zone 801.
VIP Module is zone 804 (Device
Address must be set to 4).
TeleSmart is zone 824 (Device
Address must be set to 24).
970: Bell Supervision
nd
988: 2 Wireless Receiver –
not receiving signals
st
990: 1 Wireless Receiver –
not receiving signals
997: Polling Loop (short circuit)
992: Duress
1 + ✳ panic (A key)
995:
996: 3 + # panic (C key)
✳ + # panic (B key)
999:
[1]
ADEMCO Contact ID
[0]
ADEMCO Low Speed
[1]
ADEMCO Contact ID
[0]
ADEMCO Low Speed
[0] [0]
Primary Secondary
[0]
Radionics
[0]
no
[0] [0] [0]
standard
Trbl Opn/Cls Low Bat
[0] [0] [0]
standard
Trbl Opn/Cls Low Bat