Trouble Shoo Ting & Maintenance - Exerpeutic 1111.5 Owner's Manual

Cleaning Cleaning
The recumbent bike recumbent bike can be cleaned with a soft cloth and mild detergent. Do not use recumbent bike
abrasives or solvents abrasives or solvents abrasives or solvents on plastic parts
recumbent bike recumbent bike after each use. after each use. Be careful not get excessive moisture on the after each use.
computer computer display panel as this display panel as this might cause an electrical hazard or electronics to fail. display panel as this
Please keep Please keep the recumbent bike recumbent bike recumbent bike, specially, the
to prevent screen damage. prevent screen damage. prevent screen damage. prevent screen damage.
Please inspect all assembly bolts and pedals on the machine for proper tightness Please i nspect all assembly bolts and pedals on the machine for proper tightness nspect all assembly bolts and pedals on the machine for proper tightness nspect all assembly bolts and pedals on the machine for proper tightness nspect all assembly bolts and pedals on the machine for proper tightness nspect all assembly bolts and pedals on the machine for proper tightness nspect all assembly bolts and pedals on the machine for proper tightness nspect all assembly bolts and pedals on the machine for proper tightness
every week week.
Storage Storage
Store the Store the recumbent bike recumbent bike in a clean and dry environment
TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING
PROBLEM PROBLEM PROBLEM
The recumbent bike recumbent bike recumbent bike wobbles when in use.
There is no display on the computer There is no display on the computer There is no display on the computer There is no display on the computer
console.
There is no heart rate reading There is n rate reading or heart rate rate reading
reading or or is erratic
The recumbent bike recumbent bike makes a squeaking recumbent bike
noise when in use when in use.
TROUBLE SHOOTING & MAINTENANCE TROUBLE SHOOTING & MAINTENANCE TROUBLE SHOOTING & MAINTENANCE TROUBLE SHOOTING & MAINTENANCE TROUBLE SHOOTING & MAINTENANCE
can be cleaned with a soft cloth and mild detergent. Do not use can be cleaned with a soft cloth and mild detergent. Do not use can be cleaned with a soft cloth and mild detergent. Do not use can be cleaned with a soft cloth and mild detergent. Do not use can be cleaned with a soft cloth and mild detergent. Do not use can be cleaned with a soft cloth and mild detergent. Do not use
on plastic parts. . Please
Be careful not get excessive moisture on the Be careful not get excessive moisture on the Be careful not get excessive moisture on the Be careful not get excessive moisture on the Be careful not get excessive moisture on the
might cause an electrical hazard or electronics to fail. might cause an electrical hazard or electronics to fail. might cause an electrical hazard or electronics to fail. might cause an electrical hazard or electronics to fail. might cause an electrical hazard or electronics to fail.
, specially, the computer
in a clean and dry environment in a clean and dry environment in a clean and dry environment
wobbles when in use. Turn the wobbles when in use.
or heart rate
/ inconsistent. inconsistent.
makes a squeaking makes a squeaking
Please wipe your perspiration off the wipe your perspiration off the wipe your perspiration off the
computer console, out of direct sunlight console, out of direct sunlight console, out of direct sunlight console, out of direct sunlight
away from children away from children.
SOLUTION SOLUTION SOLUTION
Turn the rear stabilizer end cap rear stabilizer end cap on the r rear stabilizer end cap
stabilizer as needed to level the stabilizer as needed to level the as needed to level the recumbent
bike.
1. Remove the Remove the Remove the computer computer console and verify
the the wires that come from the computer wires that come from the computer wires that come from the computer wires that come from the computer
console are console are properly connected to the
wires that come from the front handlebar wires that come from the front handlebar wires that come from the front handlebar wires that come from the front handlebar wires that come from the front handlebar
post. post.
2. Check if the Check if the batteries are correctly Check if the batteries are correctly batteries are correctly
positioned and battery springs are in positioned and battery springs are positioned and battery springs are positioned and battery springs are positioned and battery springs are
proper contact proper contact with batteries. proper contact
3. The batter The batteries ies in the computer console
be dead. Change to new batteries. be dead. Change to new batteries. Change to new batteries. Change to new batteries.
1. Make sure that the wire Make sure that the Make sure that the
the the hand pulse ulse sensor
2. To To ensure the pulse readout is more ensure the pulse readout is more ensure the pulse readout is more ensure the pulse readout is more
precise, please always hold on to the precise, please always hold on to the precise, please always hold on to the precise, please always hold on to the precise, please always hold on to the
handlebar grip sensors with two hands handlebar grip sensors with two hands handlebar grip sensors with two hands handlebar grip sensors with two hands handlebar grip sensors with two hands
instead of just with one hand only when instead of just with one hand only when instead of just with one hand only when instead of just with one hand only when instead of just with one hand only when
you try to test your heart rate figures. you try to test your heart rate figures. you try to test your heart rate figures. you try to test your heart rate figures. you try to test your heart rate figures.
3. Gripping the hand pulse Gripping the Gripping the
Try to maintain moderate pressure Try to maintain Try to maintain
holding onto the holding onto the holding onto the hand
The bolts may be The bolts may be loose on the
please inspect the bolts and tighten the loose please inspect the bolts and tighten the loose the bolts and tighten the loose the bolts and tighten the loose
bolts.
19
.
on the rear
recumbent
console and verify
connected to the connected to the
with batteries.
computer console may computer console
wire connection connections for
ensors are secure. secure.
ulse sensors s too tight. too tight.
moderate pressure while moderate pressure
and pulse sensor ensors.
on the recumbent bike recumbent bike,
may
,