Exerpeutic 1111.5 Owner's Manual page 14

4. Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Installation Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
Remove eight Remove eight M8x15 M8x15 Bolt
Support Bracket (1) and Seat Sliding Tube Support Bracket Support Bracket
Wrench provided. Wrench vided.
Insert the Seat Sliding Tube Insert Seat Sliding Tube Seat Sliding Tube (15) into the Bushings (54) of the
Frame Frame (3).
Attach the Attach the Seat Sliding Tube Seat Sliding Tube Seat Sliding Tube (15) to the
with eight with eight M8x15 M8x15 Bolts (23) and eight
Tighten bolts with Tighten with the Allen Wrench the Allen Wrench provided. the Allen Wrench
Adjust the Adjust the seat position and insert the Round Knob ( eat position and insert the Round Knob (17) eat position and insert the Round Knob ( eat position and insert the Round Knob ( eat position and insert the Round Knob (
Knob Knob (77), and and M12x27 Triangle Knob
M12x33 x33 Triangle Knob Triangle Knob (77),
direction to tighten. directio n to tighten.
Attach the Handlebar Attach the Handlebar (13) onto the
M8x45 M8x45 Bolts (70), two s (70), two Ø8
M8 Cap Nut Cap Nuts (32). s (32). Tighten
Screwdriver Screwdriver provided. provided.
Connect the Middle Connect the Middle Section Hand Pulse Sensor Wire
Frame (3) to the Frame (3) to the Hand Pulse Sensor Hand Pulse Sensor Wire (68) from the Hand Pulse Sensor
ASSEMBLY ASSEMBLY ASSEMBLY
Bolts (23) and eight s (23) and eight Ø8
Seat Sliding Tube Seat Sliding Tube (15). Remove
(15) into the Bushings (54) of the (15) into the Bushings (54) of the Rear Main (15) into the Bushings (54) of the
(15) to the Back Back and Seat Support Bracket
s (23) and eight s (23) and eight Ø8 Washer
provided.
Triangle Knob (66). Turn the Triangle Knob
(77), and M12 M12x27 Triangle Knob
(13) onto the (13) onto the Back and Seat Support Bracket and Seat Support Bracket (1) with two and Seat Support Bracket and Seat Support Bracket
Ø8 Curve Washer Curve Washers (25), two s (25), two Ø8
Tighten bolts w bolts with the Multi Hex Tool
ection Hand Pulse Sensor Wire ection Hand Pulse Sensor Wire ection Hand Pulse Sensor Wires (55) from the
Wire (68) from the Handlebar Wire (68) from the
12
Tool: Tool:
Washers (24) from the s (24) from the Back/Seat s (24) from the
(15). Remove bolts with (15). Remove
and Seat Support Bracket (1) and Seat Support Bracket
Washers (24) that were removed. s (24) that were removed. s (24) that were removed. s (24) that were removed.
), M12x33 x33 Triangle
. Turn the Round Knob ( Round Knob (17), Round Knob (
Triangle Knob (66) in the Triangle Knob in the clockwise
Washers (24), and two
Multi Hex Tool Multi Hex Tool with Phillips with Phillips
s (55) from the s (55) from the Rear Main
Handlebar (13).
Allen Wrench S6 Allen Wrench S6
Multi Hex Tool with Multi Hex Tool with Multi Hex Tool with
Phillips Screwdriver Phillips Screwdriver Phillips Screwdriver
Installation
Seat
with the Allen the Allen
Rear Main
(1)
clockwise
(1) with two
s (24), and two s (24), and two
Rear Main