Page 1
Foldable Semi-Recumbent Bike IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo, subject to change without Notice OWNER’S MANUAL 1110.6-062216...
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Daily) by the below methods: For Best Service Email: Service@paradigmhw.com Website: www.paradigmhw.com...
PRODUCT SAFETY Basic precautions should always be followed when using this equipment. Read all instructions before using this equipment which include the following safety instructions: 1. Read all the instructions in this manual and do warm up exercises before using this equipment. 2.
PART LIST Part # Description Part # Description Rear Frame Flat Washer Ø8.2xØ25x1.5t Front Frame Flat Washer Ø8.2 Rear Stabilizer Nylon Nut M8 Computer Bracket Hexagon Socket Bolt M8x15 Seat Post Rubber Cushion Seat Cushion Safety Pin B Left Pedal Hexagon Socket Bolt M6x12 Right Pedal Spring Washer Ø6.2...
ASSEMBLY Tool: 13 – 15mm Wrench Step 1 Remove the Safety Pin A (22) from the Rear Frame (1) and the Safety Pin B (62) from the Computer Post (17). Pull the Rear and Front Frames (1, 2) apart from each other. Rest the Support Tube (16) into the hooked plate on the Rear Frame (1).
Page 11
ASSEMBLY Tool: 5mm Allen Wrench with Phillips Screwdriver Step 2 Remove the four Hexagon Socket Bolts (73) and four Spring Washers (74) from the Computer Bracket (4). Connect the Connection Wire A (15) from the Computer Post (17) to the wire that comes from the Computer (9). Plug in the Connection Wire D (94) from the Computer Post (17) into the receptacle on the back of the Computer (9) labeled “Pulse”.
Page 12
ASSEMBLY Tool: 13- 15mm Wrench 5mm Allen Wrench with Phillips Screwdriver Step 3 The Seat Cushion (6) has 2 sets of adjustment holes. It is recommended that users between 5’1” – 5’6” use the holes at the rear of the seat. It is recommended that users between 5’7”...
Page 13
ASSEMBLY Tool: 13 – 15mm Wrench 5mm Allen Wrench with Phillips Screwdriver Step 4 Remove the four Hexagon Socket Bolts (31) and four Spring Washers (80) from the Back Frame (78). Then attach the Back Cushion (77) onto the Back Frame (78) with the four Hexagon Socket Bolts (31) and four Spring Washers (80) that were removed.
Page 14
ASSEMBLY Tool: 5mm Allen Wrench with Phillips Screwdriver Step 5 Remove the two Curve Washers (30) and two Hexagon Socket Bolts (83) from the Handlebar (82). Then attach the Handlebar (82) onto the Back Cushion Frame (78) with the two Curve Washers (30) and two Hexagon Socket Bolts (83) that were removed. Tighten the bolts with the 5mm Allen Wrench with Phillips Screwdriver provided.
Page 15
ASSEMBLY Important: Screw Right Pedal (8) into right crank hole clockwise! Screw Left Pedal (7) into Left crank hole counter-clockwise! Important: Make sure the right pedal matches up with the right crank and the left pedal matches up with the left crank. If reversed the cranks may become damaged or stripped.
COMPUTER SPECIFICATIONS: TIME --------------------------------------- 0:00-99:59 MIN: SEC SPEED ------------------------------------ 0.0-999.9 ML/H DISTANCE ------------------------------- 0.0-999.9 ML CALORIE --------------------------------- 0.0-999.9 KCAL ODOMETER ----------------------------- 0.0-999.9 ML PULSE ------------------------------------ 40-240 BEATS/MIN COMPUTER FUNTIONS: AUTO ON/OFF: If you leave the computer idle for 4 minutes, the power will shut off automatically.
ADJUSTMENTS Adjusting the Tension Control Knob To increase the resistance, turn the tension control knob in a clockwise direction. To decrease the resistance, turn the tension control knob in a counterclockwise direction. Adjusting the Seat Height Turn the seat height adjustment knob in a counter-clockwise direction until the seat post can be slid up or down.
MOVING THE BIKE Transporting the Bike Hold the Handlebar (82) and pull the machine until the wheels on the Rear Stabilizer (3) make contact with the floor. Push or pull the unit to the desired location, then gently lower the Front Stabilizer (85) to the ground.
MAINTENANCE & TROUBLE SHOOTING MAINTENANCE Cleaning The bike can be cleaned with a soft cloth and mild detergent. Do not use abrasives or solvents on plastic parts. Wipe your perspiration off the bike after each use. Be careful not get excessive moisture on the console display panel as this might cause an electrical hazard or electronics to fail.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PART REQUEST FORM Paradigm Health & Wellness, Inc EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.com NAME: _______________________________________________________ ADDRESS: ____________________________________________________ CITY ______________ STATE ______________ ZIP ___________________ TELEPHONE: (Day) _____________________________________________ (Night) ____________________________________________ SERIAL#: _____________________________________________________ MODEL#: _____________________________________________________ PURCHASE DATE: ______________________________________________ PLACE OF PURCHASE: _________________________________________ PART # DESCRIPTION...