New Holland TS-100A Assembly & Instruction Manual page 34

Hydraulic Tank & Control Valve Installation
Hydraulic Tank and Control Valve installation:
This Section covers the installation of the Hydraulic Tank and Control Valve Assembly. The Tank
and valve are shipped as an assembly.
1.
Locate Tank and Valve Asy, this will need to be lifted with a hoist, the front bumper wldmnt
is welded to the front of the tank from the factory.
2.
All Tools, Work Area, Components and Workers Hands must remain Clean when working on any
part of the Hydraulic System. All hoses and fittings should remain plugged till ready to install them
to keep them clean.
3.
All components should be rechecked for tightness and Hose routing also double checked.
Install Hydraulic Tank to Front of Tractor:
1.
Hydraulic Tank and Valve Assembly, The Hydraulic Tank, Control Valve and Pump are shipped
together (See Figure 1). The Pump should have already been mounted.
2.
Install Hyd. Tank & Control Valve Asy. To
install the tank and valve assembly you should
use an over head hoist to lift Tank and Valve
Assembly, as it is heavy and can be damaged if
dropped. The hoist will also assist when aligning
the mounting holes. There are three mounting
tabs in the rear of the tank. Mount the three rear
bolts, Three on each side. The hydraulic tank
slide under pump and between the LH & RH Tank
rails. Do not remove from hoist until tank has been
bolted on and bolts tightened
3.
Rotate Fittings to make better access to
Valve and tank connections, The fittings in the
pump and valve may have to be rotated to make
it more accessable whenconnecting the hoses.
Hose Connections To Pump And Hyd Tank: (See Figure 2)
Item Part No. Qty. Description
A 02981427 1
B 02981428 1
C 02981429 1
D 02981430 1
E 02981431 1
F 02981432 1
F ------------- 1
G 02981433 1
H 02981462 1
J ------------- 1
K ------------- 1
L ------------- 1
Maverick (NH TS-100A,115A, 125A, 135A Asy. Man) 01/05
© 2005 Alamo Group Inc.
Hose, 8FJX - 8FJX 90° - 24" Lg. w/Red Tie (Charge Filter to Pump)
Hose, 8FJX - 8FJX 90° - 21" Lg. w/ Blu Tie (Case Drain to Tank)
Hose, 12FJX - 12FJX - 23" Lg. (Pump to Suction Filter) hose under
pump and cannot be seen in drawing.
Hose, 12FJX - 12FJX - 31" Lg. w/ Red Tie (Pressure Filter to Supply)
Hose, 4FJX - 4FJX 90° - 35" Lg. w/ Red Tie (Pump Load Sense to Valve (PX)
Connects to top side of pump as shown.
Hose, 4FJX - 4FJX 90° - 20" Lg. w/ Blu Tie (Pump Regulator to Tank)
Connects to bottom side of pump not seen.
Hose #4, Connects here w/ Tee Fitting (Connect to Base End Stabilizer Cyl)
Hose, 20FJX - 12FJX - 24" Lg. (Pump to Suction Filter)
Hose, 12FJX - 12FJX 90° - 20" Lg. w/ Org Tie (Valve Return to Tank)
Hose, # 16 w/ Red Tie (Pressure from Pump to Motor) Bottom Port
Hose, # 16 w/ Orange Tie (Oil Return from Motor) Top Port
Hose. w/ Blue Tie (Oil Return from Oil Cooler to Tank)
Section 4 - 2
Inner
Mounting
Tabs
Figure 1