Programming Block Diagram - Sheet 2 - Parker 590 series Product Manual

590 Series DC Digital Converter
DIAMETER CALC.
– DIAMETER [427] – 0.00%
– MOD OF LINE SPEED [428] – 0.00%
– MOD OF REEL SPEED [429] – 0.00%
– UNFILTERED DIAMETER [430] – 0.00%
0.00 % – [424] LINE SPEED –
0.00 % – [437] REEL SPEED –
10.00 % – [425] MIN DIAMETER –
5.00 % – [426] MIN SPEED –
10.00 % – [462] RESET VALUE –
DISABLED – [463] EXTERNAL RESET –
5.0 SECS – [453] RAMP RATE –
0.000 SECS – [401] DERIVATIVE TC
SETPOINT SUM 2
– SPT. SUM 2 [451] – 0.00%
0.00 % – [444] INPUT 0 –
1.0000 – [447] RATIO 0 –
1.0000 – [448] DIVIDER 0 –
0.00 % – [443] INPUT 1 –
1.0000 – [446] RATIO 1 –
1.0000 – [466] DIVIDER 1 –
0.00 % – [445] INPUT 2 –
100.00 % – [449] LIMIT –
0.100 SECS – [403] FILTER T.C.
– OUTPUT 0 [491] –
– OUTPUT 1 [492] –
miniLINK
0.00 % – [339] VALUE 1 –
0.00 % – [340] VALUE 2 –
0.00 % – [341] VALUE 3 –
0.00 % – [342] VALUE 4 –
0.00 % – [343] VALUE 5 –
0.00 % – [344] VALUE 6 –
0.00 % – [345] VALUE 7 –
0.00 % – [379] VALUE 8 –
0.00 % – [380] VALUE 9 –
0.00 % – [381] VALUE 10 –
0.00 % – [382] VALUE 11 –
0.00 % – [383] VALUE 12 –
0.00 % – [384] VALUE 13 –
0.00 % – [385] VALUE 14 –
OFF – [346] LOGIC 1 –
OFF – [347] LOGIC 2 –
OFF – [348] LOGIC 3 –
OFF – [349] LOGIC 4 –
OFF – [350] LOGIC 5 –
OFF – [351] LOGIC 6 –
OFF – [352] LOGIC 7 –
OFF – [353] LOGIC 8 –
TAPER CALC.
– TAPERED DEMAND [452] – 0.00%
– TOT. TENS DEMAND [441] – 0.00%
0.00 % – [438] TAPER – 0.00 % – [487] STATIC COMP
0.00 % – [439] TENSION SPT. – 0.00 % – [488] DYNAMIC COMP
0.00 % – [440] TENSION TRIM – ENABLED – [489] REWIND
0.00 % – [479] FIX. INERTIA COMP –
PID
0.00 % – [480] VAR. INERTIA COMP –
– PID OUTPUT [417] – 0.00%
100.00 % – [479] ROLL WIDTH/MASS –
– PID CLAMPED [416] – FALSE
0.00 % – [498] LINE SPEED SPT
– PID ERROR [415] – 0.00%
10 – [482] FILTER T.C.
1.0 – [404] PROP. GAIN –
10 – [483] RATE CAL
5.00 SECS – [402] INT. TIME CONST. –
0.00 % – [484] NORMALISED dv/dt
–
1.0000 – [486] TENSION SCALER
100.00% – [405] POSITIVE LIMIT –
-100.00% – [406] NEGATIVE LIMIT –
0.2000 – [407] O/P SCALER (TRIM) –
0.00% – [410] INPUT 1 –
0.00% – [411] INPUT 2 –
1.0000 – [412] RATIO 1 –
0.00 % – [432] TORQUE DEMAND
1.0000 – [413] RATIO 2 –
ENABLED – [433] TENSION ENABLE
1.0000 – [418] DIVIDER 1 –
ENABLED – [434] OVER WIND
1.0000 – [414] DIVIDER 2 –
ENABLED – [408] ENABLE –
OFF – [409] INT. DEFEAT –
–
0 – [473] MODE –
20.00% – [474] MIN PROFILE GAIN –
– PROFILED GAIN [475] – 0.0
0 – [390] INPUT
0 – [394] AUX INPUT
– 0 PNO 112
OFF – [392] ADVANCED
– 0
PNO 113
SWITCH – [393] MODE
– 0 PNO 114
– 0
PNO 115
– 0
PNO 116
– 0
PNO 117
– 0 PNO 118
0 – [395] INPUT
– 0 PNO 119
0 – [399] AUX INPUT
– 379 PNO 120
OFF – [397] ADVANCED
– 380 PNO 121
SWITCH – [398] MODE
– 381 PNO 122
– 382 PNO 123
– 383 PNO 124
– 384 PNO 125
– 385 PNO 126 ENABLED – [147] SRL LINK ENABLE
0 – [140] GROUP ID (GID)
– 0
PNO 127
0 – [141] UNIT ID (UID)
EI ASCII – [149] PROTOCOL
9600 – [151] BAUD RATE
DISABLED – [153] ESP SUP. (ASCII)
USER FILTER 0.00% – [145] CHANGEBAND (BIN) –
– OUTPUT [296] – 0.00 0x00C0 – [150] ERROR REPORT
0.00 – [295] INPUT – 0xFFFF – [148] PNO. 7
The Default Application
TENSION & COMP
– TENS+COMP [478] –
– INERTIA COMP [485] – 0.00%
–
–
–
–
–
–
–
–
TORQUE CALC.
– POS. I CLAMP [435] – 0
– NEG. I CLAMP [436] – 0
–
–
–
LINK 11
– OUTPUT [391] – 0
–
–
–
–
LINK 12
– OUTPUT [396] – 0
–
–
–
–
AUX PORT P2
–
–
–
–
–
–
–
–

Programming Block Diagram - Sheet 2

15-4