Control Panels
22.1.3
B308 address settings
Octo-output module number
01, 02, 03, 04, 05, 06, 07, 08, 09
10*, 11*, 12*, 13*, 14*, 15*, 16*, 17*, 18*, 19* 101 – 108, 111 – 118, 121 – 128, 131 – 138,
20*, 21*, 22*, 23*, 24*, 25*, 26*, 27*, 28*, 29* 201 – 208, 211 – 218, 221 – 228, 231 – 238,
30*, 31*, 32*, 33*, 34*, 35*, 36*, 37*, 38*, 39* 301 – 308, 311 – 318, 321 – 328, 331 – 338,
40*, 41*, 42*, 43*, 44*, 45*, 46*, 47*, 48*, 49* 401 – 408, 411 – 418, 421 – 428, 431 – 438,
50*, 51*, 52*, 53*, 54*, 55*, 56*, 57*, 58*, 59* 501 – 508, 511 – 518, 521 – 528, 531 – 538,
*Supported by the B9512G only.
Tab. 22.17: Octo-output module valid relay numbers
22.1.4
D8128D address settings
The D8128D OctoPOPIT has two sets of DIP switches. Use the DIP switches on the top of the
unit (with the terminal strip along the left edge) to set the address for the OctoPOPIT. Use the
DIP switches at the bottom of the unit to enable or disable individual points connected to the
OctoPOPIT. The D82128D connects to the control panel through a B600.
ZONEX 1
(Points 9 -
127
9 - 16
17 - 24
25 - 32
33 - 40
41 - 48
49 - 56
57 - 64
65 - 72
73 - 80
81 - 88
Bosch Security Systems, Inc.
D8128D Address Switches
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
Installation and System Reference Guide
Corresponding relay numbers
11 – 18, 21 – 28, 31 – 38, 41 – 48, 51 – 58,
61 – 68, 71 – 78, 81 – 88, 91-98
141 – 148, 151 – 158, 161 – 168, 171 – 178,
181 – 188, 191 – 198
241 – 248, 251 – 258, 261 – 268, 271 – 278,
281 – 288, 291 – 298
341 – 348, 351 – 358, 361 – 368, 371 – 378,
381 – 388, 391 – 398
441 – 448, 451 – 458, 461 – 468, 471 – 478,
481 – 488, 491 – 498
541 – 548, 551 – 558, 561 – 568, 571 – 578,
581 – 588 , 591 – 598
ON
ON
ON
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
Appendix | en 169
ZONEX 2
(Points 129
– 247)+
*
129 - 136
*
137 - 144
*
145 - 152
*
153 - 160
*
161 - 168
*
169 - 176
*
177 - 184
*
185 - 192
*
193 - 200
*
201 - 208
2016.06 | 08 | F.01U.303.996