Seat TOLEDO Owner's Manual
Hide thumbs Also See for TOLEDO:
Table of Contents

Advertisement

OWNER'S
MANUAL
Toledo

Advertisement

Table of Contents
loading

Summary of Contents for Seat TOLEDO

  • Page 1 OWNER’S MANUAL Toledo...
  • Page 2: About This Manual

    Because this is a general manual for the This manual is divided into six large parts, Detailed contents on a given page TOLEDO range, some of the equipment and which are: functions that are described in this manual General information on a given page 1.
  • Page 3 Foreword If selling the vehicle, give all of the on-board WARNING documentation to the new owner, as it Read and always observe safety informa- should be kept with the vehicle. This Instruction Manual and its correspond- tion concerning the passenger's front air- ing supplements should be read carefully to You can access the information in this man- ›››...
  • Page 5: Table Of Contents

    Remote control ......Seat belts ......
  • Page 6 Table of Contents cruise speed (Cruise control)* ....Monitoring system Front Assist* ... . Start-Stop System* ..... . . Tiredness detection (break recommenda- tion)* .
  • Page 7: The Essentials

    The essentials Exterior view ››› ››› ››› page 44 page 9 page 45 ››› ››› page 57 page 51 ››› ››› page 11 page 10...
  • Page 8: Exterior View

    The essentials Exterior view ››› ››› ››› ››› page 46 page 47 page 47 page 142 ››› ››› ››› page 45 page 45 page 79 ››› ››› ››› page 49 page 47 page 52...
  • Page 9: Interior View (Left-Hand Drive)

    The essentials Interior view (left-hand drive) ››› ››› ››› ››› ››› page 15 page 37 page 25 page 39 page 12 ››› ››› ››› ››› ››› page 23 page 24 page 17 page 12 page 13 ››› ››› ››› ››› ›››...
  • Page 10: Interior View (Right-Hand Drive)

    The essentials Interior view (right-hand drive) ››› ››› ››› ››› ››› page 23 page 24 page 15 page 39 page 22 ››› ››› ››› ››› ››› page 36 page 27 page 17 page 15 page 49 ››› ››› ››› ››› ›››...
  • Page 11: How It Works

    The essentials How it works ››› Unlocking and locking Unlocking and locking the driver's ● Unlocking: press the  Fig. 1 button. door Unlocking the rear lid: press the  ● ››› Fig. 1 button until all the turn signals on Doors the vehicle briefly light up.
  • Page 12 The essentials ● After the driver door is opened, you have ● Insert the key in the slot and turn it in  ››› page 120 15 seconds to switch on the ignition. Once the direction of the arrow until horizontal (on this time has elapsed, the alarm is triggered.
  • Page 13 The essentials Manual release of the rear lid Bonnet  ››› page 203 WARNING Never open the bonnet if you see steam, ● smoke or coolant escaping from the engine compartment. Risk of scalding! Wait until no steam or coolant can be seen before opening the bonnet.
  • Page 14: Before Driving

    You should also Forward/back: pull the lever and move note the following: Safety switch for deactivating the electric the seat forwards or backwards. Never touch the electrical wiring of the – window buttons in the rear doors.
  • Page 15 This could limit the effect in the event of a braking manoeuvre or risk of injuries in the event of an accident. of the seat belts and the airbag system. Risk change of direction. This would prevent the of injury! ●...
  • Page 16 Never attempt to repair, adjust, remove or ● The lap part of the seat belt lies across the install parts of the belt tensioners or seat pelvis, never across the stomach. The seat belts.
  • Page 17 The essentials Adjusting the exterior mirrors not rely on these rear vision mirrors for judg- Make sure you are capable of reaching and ● ing the distance of vehicle behind. firmly holding the upper part of the steering wheel: risk of accident! ●...
  • Page 18: Airbags

    The essentials Airbags In conjunction with the seat belts, the front airbag system gives the driver and the front passenger additional protection for the head Front airbags and chest in the event of a severe frontal col- lision. Their special design allows the controlled es- cape of the propellant gas when an occupant puts pressure on the bag.
  • Page 19 Fig. 18 and the flashes, the front passenger front airbag will front passenger seat as well as in the back- Fig. 17 not trigger in the event of an accident! Have rest of the side rear seats. The locations are...
  • Page 20 ● or around the seams of the side airbag units been removed or if the panels have not been If you do not wear a seat belt, if you lean ● must be repaired immediately by a special- correctly fitted.
  • Page 21 The airbags provide protection for just one ● “AIRBAG”. accident; replace them once they have de- ployed. In conjunction with the seat belts, the head- Any work on the head-protection airbag ● protection airbag system gives the vehicle system or removal and installation of the air-...
  • Page 22: Child Seats

    Child seats Possible ways to secure child seats senger's sun visor and/or on the passenger side door frame. You can secure a child seat to the rear seat or Important information regarding the front passenger seat in the following ways: ...
  • Page 23 ● Ensure that the child seat is secured cor- Move the rear seat as far to the rear as it ● rectly using the “ISOFIX” and Top Tether* se- will go. curing rings.
  • Page 24: Starting The Vehicle

    The essentials Starting the vehicle Turning on/switching off the ignition, glow ››› ›››   tion Fig. 170 page 154 (ig- plugs reheating nition on). The control lamps will light up in this position. Otherwise, the steering lock Ignition lock ●...
  • Page 25: Lights And Visibility

    The essentials Lights and visibility  Front fog lights: move the switch to the More the lever to the required position: first position, from positions ,  or . Right turn signal: Right-hand parking Light switch  Rear fog light: move the switch completely light (ignition switched off).
  • Page 26: Interior Lights

    The essentials Windscreen wipers and window wiper ● In an emergency Knob Function blade The vehicle has broken down ●  Switches interior lights off. ● When towing or being towed  Switches interior lights on.  ››› page 127 Switches door contact control on (central po- sition).
  • Page 27: Easy Connect

    The essentials More the lever to the required position:  the windscreen with the heating and ventila- ››› page 130 tion system. The windscreen washer fluid Interval wipe for rear window. The wiper could otherwise freeze on the windscreen and ...
  • Page 28 The essentials ● Switch the ignition on. ● Press the function button to open the When the function button check box is activa- Setup ››› menu Vehicle settings Fig. ted , the function is active. If the Infotainment System is off, switch it ●...
  • Page 29: Driver Information System

    Distance, speed, temperature, volume, consumption – ››› – Chassis number, date of next SEAT service inspection, date of next oil change service page 35 Service All settings can be reset: driver assistance, parking and manoeuvring, lights, rear view mir- Factory settings –...
  • Page 30 The essentials ››› Vehicle table on page 29 press button several times     ››› Fig. WARNING Select a submenu Any distraction may lead to an accident, with ››› the risk of injury. Press the rocker switch Fig. 35 on the ●...
  • Page 31: Outside Temperature Display

    The essentials Menu Gear-change indicator Menu Function Display of the current warning or informa- Menu Function Vehicle tion texts and other system components, status depending on the equipment Information and possible configurations Driving ››› page 105. of the multifunction display (MFD) data ›››...
  • Page 32 The essentials Vehicles with an automatic gearbox* Bonnet, rear lid and doors open Illustra- ››› Key to Fig. 38 The display is only visible in tiptronic mode tion ›››  page 161. Do not continue driving!  The following display symbols mean: The bonnet is open or is not properly ›››...
  • Page 33: Journey Data

    The essentials Journey data Priority 2 warning (yellow symbols) Menu Function Symbol flashing or lit; partly combined with audible Display and storage of the values for Memory warnings. the journey and the consumption from A faulty function, or fluids which are below the correct when the ignition is switched on to The MFD (multifunction display) shows differ- ›››...
  • Page 34 The essentials Personalising the displays tion steering wheel to store the current speed Menu Function and activate the warning. In the Easy Connect system you can adjust This indicates the hours (h) and mi- ● To switch system on: adjust to the desired which of the possible displays of the MFD can Journey du- nutes (min) since the ignition was...
  • Page 35 The essentials Change from one menu to another and 120°C (250 °F) . If the engine is re- ficiency programme. After a time, the tips will quired to work hard and the outside tempera- disappear automatically. Vehicles without multifunction steering ●...
  • Page 36 The essentials sage for the driver: speed warning ex- Menu “Pause” Menu “Long-term statistics” The warning lamp  switches off ceeded! when reducing speed below the stored maxi- Continue The interrupted timer continues. View of the latest lap times: – total time mum limit.
  • Page 37 --- km or --- days If the service was not carried out by a SEAT has been greatly reduced. Because of the instrument panel display. dealership, the display can be reset as fol-...
  • Page 38: Cruise Control

    The essentials ● Switching on the CCS: Move switch is pressed on the windscreen wiper WARNING OK/RESET ››› Fig. 39 to . The system is on. If no lever, or on the multifunction steering ● For safety reasons the cruise control sys- speed has been programmed, the system will wheel.
  • Page 39: Warning Lamps

    – information on the instrument pan- – el display el display ››› Driver or passenger has not fas- page  tened seat belt.  Parking brake on. ››› page  Use the foot brake! Do not continue driving!  ›››...
  • Page 40 Fuel tank almost empty. Park the vehicle away from traffic and en- ● sure that there are no highly flammable ma- ››› Fault in airbag system and seat page  terials under the vehicle that could come into belt tensioners.
  • Page 41: Gearbox Lever

    The essentials On the instrument panel display ›››  page Start-Stop system activated.  ››› Fault in the battery. page  Start-Stop system unavailable. ››› Driving light totally or partially page ››› faulty. page  Low consumption driving status  ›››...
  • Page 42 The essentials Automatic gearbox* ● Move the gearbox lever to the required po- WARNING sition. ● Never press the accelerator when selecting ● Release the clutch. the automatic gearbox operating mode when the vehicle is stationary. Risk of accident! Selecting reverse gear ●...
  • Page 43: Air Conditioning

    The essentials ● Pull gently on both sides at the front of the ● Press the yellow plastic part with your fin- ● Press the interlock button on the selector selector lever cover. ger in the direction indicated by the arrow lever knob at the same time and move the se- ›››...
  • Page 44: Page 151

    The essentials Air distribution to footwells  ››› in Important information regarding Air recirculation air-conditioning on page 44 Cooling on/off  ››› page 151 How does the manual air conditioning* work? Temperature Air recirculation Blower : Switching the cooling system on Air distribution ...
  • Page 45 The essentials Control position Button Basic positions Air vents 4 Required tempera- Open and direct towards the  Optimum cooling 1 or 2 Do not switch on Switched on ture roof Anti-clockwise as far  Fresh air mode - blower Required position Do not switch on Switched off...
  • Page 46: Level Control

    The essentials Control position Basic positions Air vents 4 Button Windscreen and side window de- Open and direct towards the  Full right 3 or 4 Switched off frost or demist side window Mild heating Required temperature 2 or 3 ...
  • Page 47 The essentials Fuel ● Rest it on the upper part of the fuel tank ››› flap Fig. 48 Closing the fuel tank cap Unscrew the cap by turning it to the right as ● far as it will go. Close the lid. ●...
  • Page 48 The essentials Engine oil additives ● Zone : You can add oil but keep the level G 13 (TL-VW 774 J). This mixture gives the in that zone. necessary frost protection down to -25 °C No type of additive should be mixed with the (-13 °F) and protects the light alloy parts of ●...
  • Page 49 To top up, mix water with a product recom- Do not tilt the battery, as acid could leak ● cal Service. mended by SEAT. out of the vapour vents. Protect your eyes with glasses or a protective helmet! Risk of In cold temperatures, add anti-freeze.
  • Page 50 The essentials several minutes using clean water. Then seek Never use the jump leads on batteries in ● medical care immediately. which the electrolyte level is too low. Risk of explosion and acid burns! ● Neutralize any acid splashes on the skin or clothing with soap solution as quickly as pos- Never use a damaged battery.
  • Page 51: Emergencies

    The essentials Emergencies Identifying fuses situated below the dash WARNING panel by colours Using unsuitable fuses, repairing fuses or Fuses bridging a current circuit without fuses can Colour Amp rating cause a fire and serious injury. Black ● Never use a fuse with a higher value. Only Fuses in the dash panel replace fuses with a fuse of the same amper- Purple...
  • Page 52 The essentials Fuses in the engine compartment ● Open the cover in the direction indicated by the arrow  ››› page 84 Replacing a blown fuse Image of a blown fuse Fig. 57 Preparation Fig. 56 Variant 2 Fig. 55 Variant 1 ●...
  • Page 53: Bulbs

    The essentials To replace a fuse ● Apply the handbrake. Front fog light Type Switch on the hazard warning lights. Remove the fuse. ● ● Fog/cornering lights* ● Manual gearbox: Put it in 1st gear. ● Replace the blown fuse by one with an identical amperage rating (same colour and Automatic gearbox: Move the selector lever ●...
  • Page 54 The essentials Repairing a tyre with the anti-punc- ● With the tyre sealant bottle upside down, ● If the indicated pressure still cannot be fill the tyre with the contents of the sealant reached, the tyre is too badly damaged. Stop ture kit bottle.
  • Page 55: Changing A Wheel

    The essentials Changing a wheel Fitting Spare set of bulbs Press the wheel trim onto the wheel at the ● Before stowing the jack again, screw down Vehicle tool kit* cut out designed for the valve. the arm as far as it will go. Press the wheel trim on both sides in the ●...
  • Page 56 Note down the code number stamped on the front of the adapter or of the anti-theft wheel bolt. You will need this number to obtain a spare adapter from the SEAT original acces- sories programme. You should always have a wheel bolt adapter as part of your vehicle tools.
  • Page 57 The essentials Lifting the vehicle ● Grip the end of the box spanner and turn the wheel bolt about one turn anti-clockwise ››› Fig. Tightening wheel bolts ● Insert the box spanner onto the wheel bolt as far as it will go ●...
  • Page 58: Snow Chains

    The essentials Subsequent work ● Adjust the jack so that its claw surrounds ● Tighten the wheel bolts in diagonal pairs ››› the jacking point on the door sill Fig. 65 using the wheel brace. underneath the stamp. ● Alloy wheels: replace the wheel bolt caps. The wheel bolts should be clean and turn Plate wheels: replace the wheel hubcap ●...
  • Page 59: Emergency Towing Of The Vehicle

    The essentials Emergency towing of the vehi- In winter road conditions, snow chains not only help to improve grip but also improve the braking capacity. For technical reasons snow chains may only Towing be used on tyres with the following wheel rim/tyre combinations.
  • Page 60: How To Jump Start

    The essentials Notes for the driver of the towing vehicle How to jump start The power steering only works when the igni- tion is switched on and the vehicle is moving, The tow rope must be taut before you drive ●...
  • Page 61 The essentials Jump lead terminal connections Please note the safety warnings referring to The discharged battery must be properly ● ● working in the engine compartment connected to the vehicle electrical system. 1. Switch off the ignition of both vehicles ›››...
  • Page 62: Changing The Windscreen Wiper Blades

    The essentials Starting WARNING Position the leads in such a way that they ● cannot come into contact with any moving 7. Start the engine of the vehicle with the ● Please note the safety warnings referring to parts in the engine compartment. boosting battery and let it run at idling working in the engine compartment speed.
  • Page 63 The essentials Service position Changing the rear window wiper blade* Close the bonnet. ● ● Switch the ignition on and off. Press the lever to position ● ››› ›››   Fig. 139 page 131, the wind- screen wiper arms are set to the service posi- tion.
  • Page 64: Safety

    Never drive when your driving ability is im- – Adjust front seat, head restraint and rear vi- – paired (e.g. by medication, alcohol, drugs). WARNING sion mirrors properly according to your size.
  • Page 65: Correct Position For Passengers

    ● can lead to severe injuries. Safety is everyone's business! For your own safety and to reduce the risk of Adjust the driver seat so that there is at ● injury in the event of an accident, we recom- »...
  • Page 66 Move the seat backrest to an upright posi- – wheel with both hands on the outside of the dash panel, out the window or on the seat. An tion so that your back rests completely ring at the 9 o'clock and 3 o'clock positions.
  • Page 67 Never put your feet on the dash panel. ● ● Never put your feet on the surface of a seat. To reduce the risk of injury in the event of a Seat belts can provide optimal protection on- Do not allow anyone to travel in the foot- ●...
  • Page 68 (e.g. by “falling” back into the seat when entering the Adjust the head restraint so that its upper –...
  • Page 69: Pedal Area

    This ● Pedal area would reduce the pedal area and could ob- ten and wear the seat belt belonging to his or her seat. Children must be protected with an struct the pedals. Risk of accident. appropriate child restraint system.
  • Page 70 Safety The protective function of seat belts Instruct your passengers to fasten their This is why it is so important to fasten seat – seat belts properly before driving off. belts before every trip, even when "just driv- ing around the corner".
  • Page 71 Always keep both feet in the footwell in ● specialised workshop. Renewal may be nec- front of your seat as long as the vehicle is in essary even if there is no apparent damage. motion. The belt anchorage should also be checked.
  • Page 72: How To Properly Adjust Your Seatbelt

    25 km/h (15 mph) to 50 km/h vehicle interior in an accident. Passengers in (30 mph), for example, the corresponding ki- the rear seats who do not use seat belts en- netic energy is multiplied by four. danger not only themselves but also the front ›››...
  • Page 73 Always engage the retractor lock when you ● The following features are available to adjust plate and pull it slowly across your chest and are securing a child seat in group 0, 0+ or 1 the seat belt in the shoulder region: lap. ›››...
  • Page 74: Seat Belt Tensioners

    This function at all. retracts and tightens the seat belts, reducing Location of the belt height adjuster.
  • Page 75: Airbag System

    Brief introduction their age, size or weight. Always maintain the greatest possible dis- If you are not wearing a seat belt, or if you ● tance between yourself and the front airbag. Why is it so important to wear a seat...
  • Page 76 (if the interior ● cle hits (hard/soft), angle of impact, vehicle ● The seat belts and airbags can only provide light switch is in the courtesy light position); maximum protection if the occupants are speed, etc.
  • Page 77: Deactivating Airbags

    We recommend that you contact an author- checked immediately by a specialised work- seconds (self-diagnosis) and the instrument ised SEAT dealer for the disabling of other air- shop. Otherwise, in the event of an accident, panel display* shows AIRBAG/TENSIONER .
  • Page 78 – try regarding the disabling of airbags. Do not force it if you feel resistance, and At your authorised SEAT dealer you can find ● make sure you have inserted the key fully. information on which vehicle airbags can be disabled.
  • Page 79: Transporting Children Safely

    For safety rea- the child! Read the additional information carefully sons, the child seat should be installed in the Never allow a child to be transported in a ›››...
  • Page 80: Child Seats

    ECE R44 standard bear the ● Only one child may occupy a child seat test mark on the seat (the letter E in a circle ››› page 78, Child seats. with the test number below it).
  • Page 81: Emergencies

    Self-help ›››  page 53 We recommend you use the first-aid kit and ● the warning triangle from the SEAT Original WARNING Emergency equipment Accessories programme available in author- The factory-supplied jack is only designed ● ised SEAT dealers.
  • Page 82: Tyre Repairs

    ● The set of anti-theft wheel bolts or the ing away unexpectedly. adapter are available from authorised SEAT TMS Anti-puncture kit (Tyre Mobility dealers. ● If the vehicle has been fitted with tyres or...
  • Page 83 A new can of sealant can be acquired from ››› Read and observe the safety warnings The Tyre Mobility System contains the follow- the selection of SEAT Original Accessories. Introduction on page ing components: Change the tyre repaired using the Tyre ●...
  • Page 84: Towing The Vehicle

    Emergencies ››› Towing the vehicle The valve extractor Fig. 84 has a slot in Do not remove the foreign body, e.g. bolts – its lower end that fits onto the valve insert. or nails, from the tyre. This is used to remove the valve insert from Introduction Unscrew the tyre valve cap.
  • Page 85 CAUTION We recommend you use the towrope or tow- ● bar available in the SEAT Original Accessories The towline anchorage must be screwed in as programme from authorised SEAT dealers. far as it will go. Otherwise there is a risk of Towing a vehicle requires a certain degree ●...
  • Page 86: Fuses And Bulbs

    Emergencies Fuses and bulbs Fuses in the dash panel CAUTION ● To prevent damage to the vehicle's electric Fuses system, before replacing a fuse always turn off the ignition, the lights and all electrical elements and remove the key from the igni- Introduction tion.
  • Page 87: Changing Bulbs

    Fuses and bulbs Changing bulbs requires a certain degree of Note CAUTION practical skill. If in doubt, we recommend you In the vehicle, there are more fuses than ● Remove the ignition key before working on have defective bulbs changed by a special- those indicated in this chapter.
  • Page 88 Emergencies Changing side light bulbs Changing main beam headlight bulb generated by the bulb, they will be deposited on the reflector and damage its surface. Double headlight bulbs Changing side light bulbs. Changing main beam headlight Fig. 88 Fig. 89 bulbs.
  • Page 89 Fuses and bulbs ››› ››› Changing dipped beam light bulbs Remove connector Fig. 91 by pulling Turn the bulb holder Fig. 92 anti- – – outward. clockwise and remove it. ››› Unclip the retainer spring Fig. 91 Remove the bulb by pressing on the bulb –...
  • Page 90: Changing The Fog Light Bulbs

    Emergencies Removing the bulb holder Fit the replacement bulb in the bulb holder – and turn clockwise as far as it will go. Check whether the new bulb is working. – Changing the fog light bulbs Front fog light bulb Front fog light.
  • Page 91: Changing The Rear Lights (On The Side Panel)

    Fuses and bulbs ››› Changing the rear lights (on Pull the rear light unit backward ( Fig. 97 – ) to remove the light from its housing. the side panel) Removing the rear light Removing the bulb holder Retaining screws on reverse side of Fig.
  • Page 92 Emergencies Changing bulbs Position of the bulbs ››› Fig. 100 Bulb function Turn signals: PY21W NA LL Side lights-brake lights: P21/5W Side lights: P21/5W Note Check the condition of the seal. If damaged, a Fit the tail light unit. Fig. 102 replacement can be acquired from an Official Service.
  • Page 93: Changing Tail Lights (On The Rear Lid)

    Fuses and bulbs Changing tail lights (on the Open the cover to access the lights, turning – it by hand in the direction indicated by the rear lid) arrows. Access the lights by disconnecting the con- – Removing the bulb holder ›››...
  • Page 94: Changing The Bulb On The Number Plate

    Emergencies Lightly press the defective bulb into the Screw in the bulb holder using the corre- – – bulb holder, then turn it anti-clockwise and sponding screw. remove it. Make sure the connector is correctly in – Fit the new bulb, pressing it into the bulb place.
  • Page 96 Operation Fig. 108 Interior.
  • Page 97: Operation

    Start-Stop system General instrument panel – ....Depending on the equipment, Front passenger heated seat – ..glove compartment with: Electric window controls .
  • Page 98: Instruments And Warning Lamps

    Operation Instruments and warning lamps Instruments View of instrument panel Instrument panel, on dash panel Fig. 109 ››› ››› Details of the instruments Fig. 109: ator) before the needle reaches the red Fuel gauge page 100. ››› zone Rev counter (with the engine running, in WARNING Engine coolant temperature display hundreds of revolutions per minute).
  • Page 99 Instruments and warning lamps ››› We recommend that you avoid high revs and ● Shift lever position page 160. CAUTION that you follow the recommendations on the Recommended gear (manual gearbox) ● ● To prevent damage to the engine, the rev gear-change indicator.
  • Page 100 Operation Time Second speed display (mph or km/h) panel when the vehicle is in low consump- tion status. ››› To set the time, keep the button Fig. 109 In addition to the speedometer, the speed ● pressed for more than 3 seconds to select can also be displayed in a different unit of Identifying letters on engine (MKB) the hour or minute display.
  • Page 101 Instruments and warning lamps Odometer/trip recorder Engine cold Depending on the equipment, some set- ● tings and instructions can also be carried out The odometer shows the total distance cov- If only the diodes in the lower part of the in the Easy Connect system.
  • Page 102: Control Lamps

    The fuel tank has a capacity of approx. 55 li- lamp illuminates to instruct the driver or  tres. When the needle reaches the reserve front passenger to fasten their seat belt. The ››› area, the  page 104 warning symbol illu-...
  • Page 103 Instruments and warning lamps Engine oil The control lamp  flashes yellow (oil level front passenger fastens their seat belt  ››› page sensor faulty) The control lamp flashes red (oil pressure  The informative display indicates: low) Oil sensor. Workshop! Alternator ...
  • Page 104 Operation Stability system (ESC)  Traction control system (ASR)  If the coolant is situated in the prescribed area, the high temperature may be due to a fault in the cooling system fan. Check the ra- If the control lamp  flashes, the ESC is If the control lamp ...
  • Page 105 Instruments and warning lamps Engine management  (petrol en- Go to a technical service. Note gines) The rear side lights and number plate light WARNING contain several bulbs. The control lamp  If the  warning lamp is illuminated, there is If the warning lamp illuminates together ●...
  • Page 106 Operation Fuel reserve  to burn. On completion of the cleaning the Airbag/belt tensioner disabled! warning lamp will switch off. If the front passenger airbag has been disa- The  warning lamp illuminates when ap- If the lamp  does not turn off, or the three bled with the airbag switch located in the proximately only 7 litres of fuel remain in the lamps turn on (particulate filter , fault in...
  • Page 107: Introduction To The Easy Connect System

    Introduction to the Easy Connect system* Fog lights  Introduction to the Easy Note Connect system* If the battery is disconnected the warning The control lamp  lights up when the fog lamp  lights up when the ignition is switch- ›››...
  • Page 108 Operation Function buttons in the Page vehicle’s settings menu ››› ESC system page 167 ››› Tyres page 216 ››› Driver assistance table on page 26 ››› Parking and manoeuvring page 168 ››› Vehicle lights table on page 26 ››› Rear vision mirrors and wind- table on page 26 screen wipers ›››...
  • Page 109: Communications And Multimedia

    Communications and multimedia Communications and multi- media Steering wheel controls* General information The vehicle includes a multifunction module from where it is possible to control the audio, telephone and radio/navigation functions without needing to distract the driver. There are two versions of the multifunction module: ●...
  • Page 110 Operation Operating the audio system Fig. 112 Controls on the steering wheel. Button Radio Media (except AUX) Turn Up/down volume Up/down volume Up/down volume Press No function No function No function Mute Pause Mute Short press: switch to the previous song Search for last station No function Hold down: quick rewind...
  • Page 111 Communications and multimedia Operating the audio system + telephone Fig. 113 Controls on the steering wheel. Button Radio Media (except AUX) Telephone Navigation Turn Up/down volume Up/down volume Up/down volume Up/down volume Up/down volume Press Mute Pause Mute Mute Mute Short press: answer/hang up Short press: access to the tele- Short press: access to the tele-...
  • Page 112 Operation Button Radio Media (except AUX) Telephone Navigation Change menu on instrument Change menu on instrument Change menu on instrument Change menu on instrument Change menu on instrument panel panel panel panel panel Enable/disable voice control Enable/disable voice control Enable/disable voice control No function Enable/disable voice control Acts upon the dash panel...
  • Page 113: Multimedia

    Fig. 114. paired or changed, the remote control key The MDI input is composed of the USB and must be adapted by an authorised SEAT deal- AUX-IN inputs. er. Only then can the remote control key be used again. The purpose of the MDI input is to connect ®...
  • Page 114 Operation Deactivating the Safe lock The remote control function may be tempo- Note ● rarily limited by interference from other Press button twice in 2 seconds. Further – ● Only use the remote control when the transmitters near the vehicle that operate on ›››...
  • Page 115: Keys

    ››› Fig. 116  or with remote control ››› Fig. 116 . SEAT recommends you ask a specialised workshop to replace the battery. WARNING The battery is located to the rear of the vehi- » ● Never leave the key inside whenever you cle key, under a cover.
  • Page 116: Central Locking System

    Operation ››› Changing the battery tow-away protection system page 120. Go Note to a technical service. Unfold the vehicle key shaft. ● If it is not possible to unlock or lock the vehi- cle with the remote control key once the bat- ●...
  • Page 117 Activation of the single door setting can be ● If the vehicle is equipped with an anti-theft requested at your SEAT dealer. alarm system, you have 15 seconds from the time the door is opened to insert the key in ●...
  • Page 118 Operation Safe Lock Locking of all doors, the boot lid and the fuel Note tank flap ● The anti-theft alarm switches on automati- The central locking system is equipped with a ››› Press the button  Fig. 120. The warning –...
  • Page 119 Opening and closing ● Keyless-Entry: unlocking of the vehicle with Note the handles on the four doors or the button The handles and the central lock buttons will located on the boot hatch. ››› not work if the Safe lock page 116 is acti- ●...
  • Page 120 Operation Locking the vehicle with a second key ● Touch the surface sensor once (arrow) few seconds on the lock sensor surface ››› on the door handle. The door being operated Fig. 122 located on the exterior part of If there is a vehicle key inside the vehicle and must be closed.
  • Page 121: Anti-Theft Alarm System

    Opening and closing Activating the childproof lock 30 seconds after emitting the radio frequen- happen if any other radio frequency signal cy signal, the system will be reactivated. interferes with the key signal (e.g. from a mo- Turn the slot in the direction of the arrow –...
  • Page 122: Rear Lid

    The vehicle interior monitoring system and ing time extension function can be activated the tow-away protection system must be de- or deactivated at a SEAT Authorised Service, activated if there is a danger of the alarm be- which will provide all of the necessary infor- ing triggered due to movements by children mation.
  • Page 123: Opening And Closing Of Electric Windows

    Opening and closing Rear lid Opening and closing of electric This system may or may not be operative, de- pending on the situation of the vehicle. windows If the rear lid is locked then it cannot be opened, however if it is unlocked then the Operation of the electric windows opening system is operative and the rear lid may be opened.
  • Page 124 Operation Closing The roll-back function will only be disconnec- Do not leave the side windows open at high ● ted if you once again attempt to close the speeds, as this will overly increase fuel con- Press the respective button gently to close –...
  • Page 125: Lights And Visibility

    Lights and visibility Lights and visibility Switching off lights (except daytime driving the inside and in front of the light. By switch- lights) ing on the lights, the area through which the beam of light is projected will quickly be ›››...
  • Page 126 Operation Driver only, luggage compartment fully ● Insert the key and switch on the ignition, other drivers in the darkness, if it is raining loaded. holding it in this position for 3 seconds. or in conditions of poor visibility. Then, switch off the ignition. The daytime CAUTION running light is now activated and the corre- Note...
  • Page 127 Lights and visibility long as you hold the lever, e.g. when If the light switch is in position , the sym- CAUTION changing lanes. bol  located next to the light switch will il- Never use the main beam headlights or the luminate.
  • Page 128 ››› The  page 100 warning lamp lights up on using parts from the original SEAT parts The fog lights are switched off ● the general instrument panel if the front fog catalogue, only the rear fog light on the trail- lights are switched on.
  • Page 129: Parking Lights

    Lights and visibility Function “Coming Home”/“Leaving The lights is switched off when all the doors at the same time as the turn signals when and the boot lid are closed. the hazard warning lights are switched on. Home”* The hazard warning lights also work when If a door or the boot lid remains open, the the ignition is switched off.
  • Page 130: Interior Lights

    The light distribution of the halogen and full- ● 30 seconds after all of the doors have been LED headlights of the SEAT Toledo allows the closed specific “tourist light” values to be met with- out the need for stickers or changes in the...
  • Page 131: Visibility

    Lights and visibility Rear interior light Glove box light Switch the heated rear window on or off by – ››› pressing the button Fig. 136, the  The light will come on automatically when warning lamp in the button will come on or the glove compartment is opened.
  • Page 132 For safety reasons, the wiper blades should ● switched on. be changed once or twice a year. They can be purchased at a SEAT Authorised Service. The speed of the automatic wipe in case of rain is automatically adjusted according to Front passenger's sun visor.
  • Page 133 Lights and visibility Automatic rear window wash and wipe* The rain sensor* is part of the intermittent On vehicles equipped with windscreen ● wipe function. washer jets, these are heated once the en- Press the lever fully forward to position –...
  • Page 134: Rear Vision Mirrors

     page 12 engine is running. remove any ice with a de-icer spray. Set the driver seat in such a way that the Do not touch the exterior mirrors when the ● pedals can be fully depressed with your legs CAUTION heating system is running.
  • Page 135: Seat Functions

    Correct adjustment WARNING of the head restraint, together with the seat Do not use the heated seat if your perception belts, ensure effective passenger protection of pain and/or temperature or that of your ›››...
  • Page 136 Do not use the heated seats if nobody is ● sitting on them or if there are items attached to or lying on them, such as a child seat or a bag, etc. This could lead to a fault in the seat heating elements.
  • Page 137 Take care when handling the rear backrests Insert the seat belt latch plate into hole – so as not to damage the seat belts. The seat ››› Fig. 144 located on the corresponding belt must never be left behind the lifted back- side of the vehicle –...
  • Page 138: Transport And Practical Equipment

    Driver seat: storage compartment Fig. 147 ● For safety reasons, all storage compart- Storage: cooling control. Fig. 146 ments must be closed while the vehicle is There is a compartment below the driver seat moving. ››› Fig. 147 to store the reflective vests.
  • Page 139 Drink holder in rear seat armrest Storage pocket under the front seats There is a storage pocket on the rear part of the backrest of the front seats.
  • Page 140: Cigarette Lighter

    Operation Cigarette lighter* Ashtrays* moved. Therefore, never leave children unsu- pervised in the vehicle. Note The 12 V power socket of the cigarette ● lighter can also be used as a power source for ››› electrical appliances page 139, 12V Power socket.
  • Page 141 Transport and practical equipment ››› Additional information page 193, Acces- WARNING protect them from any damage caused by sories and modifications to the vehicle. fluctuations in voltage. Never put flammable materials in the ashtray. ● Follow the instructions for use of connected Risk of fire! WARNING appliances!
  • Page 142 Operation Storage compartment for eyeglasses* Coat hooks* Front seat backrest net pockets The coat hooks are located on the B-pillars and on the handles on the interior lining above each rear door. WARNING Make sure that any items of clothing hang- ●...
  • Page 143: Storing Objects

    Transport and practical equipment ››› Compartments in the centre console There is a bottle carrier in part Fig. 157 CAUTION of the storage compartment in the front door. ● The compartments are designed to hold small objects with a total weight of 1.5 kg. WARNING Make sure you do not damage the storage ●...
  • Page 144: Luggage Compartment

    Always use suitable and undamaged straps – avoid accidents. to secure luggage and other objects to the ● Never secure a child seat on the fastening ››› ● Never exceed the allowed axle weights or fastening rings in Loading the lug- rings.
  • Page 145 “projectile” strikes an occupant Retaining elements* by placing the load so that it stops the seat as it flies through the vehicle interior. from folding backward in the event of being hit from behind.
  • Page 146 Operation Retaining nets* CAUTION WARNING The rings support a maximum load of 3.5 kN Do not exceed the maximum load that the (350 kg). nets can support. Heavy objects cannot be safely secured. Risk of injury! Note CAUTION The front ring is below the folding back- ›››...
  • Page 147: Roof Rack

    There must be no objects in the space be- – tween the open shelf and the backrest of Fitting the shelf the rear seat. Place the shelf on the side supports on the – trim. Note ›››...
  • Page 148 ● lowed maximum weight. Risk of accident! Follow the instructions given in the manual. CAUTION Roof load Only use SEAT-authorised roof carriers. ● Where roof carriers from other systems are ● The maximum permissible roof load (includ- used or where they are not fitted properly,...
  • Page 149: Air Conditioning

    Air conditioning Air conditioning If the interior temperature can be reached Note without switching on the air conditioning, the ● Used air escapes through ventilation slots fresh air mode should be used. Heating and air conditioning in the rear of the luggage compartment. Smoking is not recommended while the air ●...
  • Page 150: Heating And Fresh Air

    Operation Air vents Air vents Fig. 166 Heating and fresh air Opening air vents 3 and 4 The flow of air from the vents is controlled us- ››› ››› ing control Fig. 167. Vents 3 Fig. 166 Turn the vertical circular control upwards. –...
  • Page 151: Air Conditioning (Manual)

    Air conditioning Read the additional information carefully In the thaw position of rotary switch , the plied to the footwell area. This could limit ›››  page 43 entry of air into the vehicle interior is always heating comfort. from the outside. Temperature selection WARNING ›››...
  • Page 152 Operation Turn rotary control to position 0 to – Note all of the conditions for cooling system oper- switch the blower off. ations are met. Cooling is indicated as availa- A visit to the specialised service once a year ble once all of the conditions are met ›››...
  • Page 153: Climatronic* (Automatic Air Conditioning)

    Air conditioning In the thaw position of rotary switch , the WARNING entry of air into the vehicle interior is always ››› Read and observe the safety warnings from the outside. Important information regarding air-condi- tioning on page Climatronic* (automatic air conditioning) General notes Climatronic: controls.
  • Page 154 Operation Starting the Climatronic Adjusting the temperature Note The corresponding function will be switched ● A visit to the specialised service once a ● When you switch on the ignition, control on when a button is pressed, turning on the year is recommended to clean the Climatronic ›››...
  • Page 155: Driving

    Driving Switching off air recirculation mode Driving WARNING ››› Press button Fig. 169 and the  ●  17 ››› Read and observe the safety warnings symbol disappears from the screen. Starting and stopping the en- Important information regarding air-condi- tioning on page gine WARNING...
  • Page 156: Ignition Lock

    The engine can only be started with the the key is inserted into the ignition. The elec- off, engine stopped, steering can be locked original SEAT key. tronic immobiliser is automatically activated Loud running noises may be heard briefly ●...
  • Page 157 Driving If the steering lock is engaged and it is diffi- ● Immediately after pushing the start-up but- cult or impossible to turn the key to position ton, keep the vehicle key next to the steering ››› , release the lock by turning the steering column Fig.
  • Page 158: Brakes And Brake Servo Systems

    Operation ● Press the clutch pedal all the way down WARNING rol engine vehicle at low speed. Otherwise, ››› ››› Fig. 170 page 154 and start the engine the brake servo might not work properly. Risk If vehicle keys are used negligently or with- , without pressing the accelerator.
  • Page 159 Driving sion, clean the brake discs by braking fully Where braking is not necessary, do not In the event of a fault in the ABS system, ● ● several times at a high speed. wear down the brake pads by pressing down the ESC, TCS and EDL are switched off auto- gently on the brake pedal.
  • Page 160: Manual Gearbox

    Operation Handbrake Manual gearbox Note Do not rest your hand on the gear lever while Changing gears driving. The pressure of your hand could lead to premature wear of the gear system. Automatic gearbox Basic information The gearbox changes up and down automati- Fig.
  • Page 161 Driving If, while the vehicle is moving, the selector ped for a short period, e.g. at intersections. CAUTION lever is accidentally moved to position N, re- Applying the brake is enough. However, the ● In DSG automatic gearboxes, the double lease the accelerator and wait for the engine engine must remain idling.
  • Page 162 Operation Selector lever positions – Parking position – Drive (forwards) In this position, the driven wheels are me- In this position, the gearbox automatically chanically locked. changes to a lower or higher gear, depending on engine requirements, the driving speed The parking position can only be selected and the gear shift programme.
  • Page 163 Driving Tiptronic Shifting down warning lamp will light up on the general in- ››› strument panel  page 105. Push the selector lever gently backwards – ››› Fig. 177. When the selector lever merely moves through position N (e.g. when moved from R The manual gearbox can be activated when to D), the lever lock is not applied.
  • Page 164 Operation Driving programmes When driving along mountain roads, the There is a fault in the gearbox. Stop the vehi- gearbox adapts to the gradients. This avoids cle in a safe place and do not continue driv- Your vehicle is equipped with an electronical- having to frequently change gears when driv- ing.
  • Page 165: Run-In And Economical Driving

    Slowly increase the engine speed until – ture of your new SEAT. New tyres reaching the maximum permitted speed of the engaged gear, i.e. the maximum per- Constructive measures to encourage recy- New tyres must be submitted to “running in”,...
  • Page 166 Operation ● Increased use of single-grade materials. ● Use of systems for the recovery of residual Never use substances for additional under- ● heat (thermal recovery, enthalpy wheels, body protection or anti-corrosives for the ex- Plastic parts and elastomers are marked in ●...
  • Page 167 Driving ahead. The braking effect achieved in this greater than the amount of fuel needed to re- mend avoiding short trips whenever possi- way helps to reduce the wear of brakes and start the engine. ble. tyres; emissions and fuel consumption are The engine takes a long time to warm up reduced to zero (disconnection due to iner- Maintain the correct tyre pressures...
  • Page 168: Wading And Driving Off-Road

    Clean and dry the brakes as soon as possi- ● fan at high speeds, the rear window heating ble after driving through water by breaking and the seat heaters*. intermittently. Carry out braking in order to dry the brakes and clean the brake discs only Note if traffic so permits.
  • Page 169: Driver Assistance Systems

    Driver assistance systems Driver assistance systems The ASR should be switched on at all times. Note Only under certain circumstances should the After driving through water we recommend system be switched off, e.g. Braking and stability systems that you contact a specialised service for an ●...
  • Page 170: Parking Aid

    Operation without having to use the handbrake. The The TCS  warning lamp on the general them about obstacles detected in front and ››› brake pressure drops as the accelerator ped- dash panel flashes when the system is work- behind the vehicle page 170.
  • Page 171 – a SEAT Official Service or in a specialised ● Certain surfaces of objects and garments with long grass; workshop.
  • Page 172 Operation Parking system plus* 0.90 m central area 1.60 m 1.60 m As you approach the obstacle, the time inter- 0.90 m val between the audible warnings will be re- duced. When you reach around 0.30 m the As you approach the obstacle, the time inter- warning will be constant: Do not continue to val between the audible warnings will be re- ›››...
  • Page 173 Driver assistance systems Manual disconnection of Parking Aid Change from reduced view to full view be displayed and the segments will be shown on the left side of the screen Press the  button again. Engage reverse gear or turn the selector ●...
  • Page 174 171. tivation Segments of the visual indication Moreover, with the SEAT Media System Front volume Plus/Navi System radios, a yellow trail indi- cates the vehicle's expected journey based Volume in the front and rear area. on the steering wheel angle.
  • Page 175: Rear Assist "Rear View Camera

    Driver assistance systems Error messages Parking System Plus all. Take special care with thin posts, fences, railings or trees that might not be displayed The distance to possible obstacles at the rear When the Parking Aid is activated or when it on screen and could damage the vehicle.
  • Page 176 Familiarising yourself with the system To change these settings: To familiarise yourself with the system, the orientation lines and their function, SEAT rec- Park the vehicle in a safe place. ● ommends practising parking and manoeu- ●...
  • Page 177 Driver assistance systems Parking and manoeuvring with the too much traffic or in a car park when there In combination with the Parking System Plus ››› are good weather and visibility conditions. page 168, the camera image will cease to rear assist be transmitted immediately when reverse Cleaning the camera lens...
  • Page 178: Cruise Speed (Cruise Control)

    Operation Setting the speed Side lines: extension of the vehicle (the The cruise control system allows you to drive approximate width of the vehicle plus the at a constant speed of 30 km/h (19 mph) or rear view mirrors) on the road surface. higher without having to press the accelera- tor.
  • Page 179: Monitoring System Front Assist

    Driver assistance systems Adjusting the stored speed Monitoring system Front As- set and the memory will be deleted. The ve- hicle must be moving at a speed of over sist* Increasing speed by pressing the accelerator 30 km/h (19 mph) and switch pressed pedal again to SET for it to be set.
  • Page 180 If the driver fails to react to the pre-warning, must brake immediately or dodge the obsta- SEAT recommends visiting a SEAT dealership. the system may actively intervene in the cle. brakes when driving at a speed of between ●...
  • Page 181 SEAT recom- cur, for example, in a closed car park or due Radar sensor mends visiting a SEAT dealership for this pur- to the presence of metallic objects (e.g. rails pose. on the road or sheets used in road works).
  • Page 182 Switching distance warning on and off SEAT recommends leaving the Front Assist al- ››› If the safe distance with regard to the vehicle ways switched on. Exceptions page 180,...
  • Page 183: System Limitations

    Driver assistance systems City Emergency braking function ● If it intervenes several times unnecessarily. ● If the ASR has been manually disconnec- ted. If the radar sensor is covered temporarily ● with some kind of accessory, such as an ad- ●...
  • Page 184: Start-Stop System

    Emergency braking function. Take it to a spe- The system is automatically switched on ev- essary warnings and intervene inopportunely cialised workshop, SEAT recommends visiting ery time the ignition is switched on. in braking, such as in work areas or if there a SEAT dealership.
  • Page 185 ● Switching the Start-Stop system on and off ● Vehicle not on a very steep slope If the driver seat belt is unfastened for more The Start-Stop system can be switched on Engine speed below 1,200 rpm. ● than 30 seconds in Stop phase, the engine ›››...
  • Page 186: Tiredness Detection (Break Recommenda- Tion)

    Operation Tiredness detection (break rec- Note START MANUALLY Start the engine manually ommendation)* ● Tiredness detection has been developed for WARNING driving on motorways and well paved roads only. Introduction If the engine is switched off, neither the ● brake servo nor the power steering will work. ●...
  • Page 187: Towing Bracket Device

    15 minutes, SEAT Original Accessories, it meets all the rel- The message can be recalled to the instru- when the ignition is switched off or when the evant technical and legal requirements.
  • Page 188 Operation Trailer weight Driving with a trailer tude, this also reduces climbing ability, which requires a reduction of the weight of Trailer weight Exterior mirrors the vehicle with a trailer by 10% for every 1000 m increase in altitude. The weight of The combined vehicle and trailer must be Check whether you can see enough of the the assembly is calculated by adding the ve-...
  • Page 189: Towing Bracket Device For Trailer

    The vehicle anti-theft alarm device driving lights or other sources of electrical ine SEAT accessory, it meets all national tech- ››› could cause the alarm to sound page 119, current.
  • Page 190 Operation Description Clamping bush WARNING Clamping bush cap ● Before driving with the ball-headed bar fit- ted, verify its correct assembly and place- Ball head cover ment in the clamping bush. Ball-headed bar ● Do not use the ball-headed bar if it is not Locking balls correctly placed and fixed in the clamping Centred...
  • Page 191 Towing bracket device Placing in service position The manual regulator will remain in this posi- tion. ››› Service position Fig. 195 is in an open position – the key ar- ● row points to the “unlocked” symbol. The key cannot be removed from the key slot. ●...
  • Page 192 Operation Assembly of the ball-headed bar Verify the correct placement of the ball- – ››› headed bar page 191. WARNING ● Do not hold the manual regulator with your hand when fitting the ball-headed bar since you could sustain injuries to your fingers. ●...
  • Page 193 Towing bracket device Verification of correct placement WARNING Only use the towing bracket device when the ball-headed bar is properly fitted! Disassembly of the ball-headed bar Unblock the ball-headed bar. Fig. 200 Remove cover from over the regulator – Correct placement of the ball-head- Fig.
  • Page 194 Operation The ball-headed bar should be placed in the Clean the ball-headed bar thoroughly be- ● service position so that it is ready to be inser- fore returning it to the on-board toolbox. ››› ted into the clamping bush Place the cover over the clamping bush –...
  • Page 195: Advice

    SEAT directive. Damage caused by technical modifications tions, always request advice from an Author- that are not made with the consent of SEAT Modifications and corrections of the front ››› ised SEAT dealer will be excluded from the warranty –...
  • Page 196: Care And Cleaning

    Risk of damage to paintwork. from the SEAT Original Accessories pro- crease the risk of serious or fatal injuries in gramme available in SEAT dealers. Please fol- If washing the vehicle with a hose in win- ● an accident.
  • Page 197 Rinse the sponge or glove thoroughly and of- ● We recommend that you visit an authorised ten. SEAT dealer to clean and care for the interior car washes of your vehicle, due to the problems that may Wheels, sills and underside should be arise when cleaning and caring for the interi- cleaned last.
  • Page 198 Never use warm or hot water to remove CAUTION snow and ice from the reverse camera lens, We recommend you leave paint damage re- as it could crack the lens. pairs to a SEAT Authorised Service. ● Never wax the windows.
  • Page 199 We recommend the use of products from ● CAUTION avoid damaging the surface of the glass, the the selection of SEAT Original Accessories to care for the door lock cylinder. scraper should only be pushed in one direc- ● Never rub the headlights to dry them and tion and not moved to and fro.
  • Page 200 Given that damage to the protective coating away any stains using lighter fluid. Do not clean the seat upholstery with damp during driving cannot be completely ruled products, as this could damage the seat...
  • Page 201 En- Use a grease-dissolving product to treat moisturise the leather, keep it supple and sure that the seat belts do not come into con- dried-in, fat-based stains. able to breathe. In addition, it will also help tact with corrosive fluids such as acids, etc.
  • Page 202: Checking And Refilling Levels

    Advice Checking and refilling levels The correct type of fuel for your vehicle is in- Make sure that the inertia reel seat belts ● dicated on a sticker on the inside of the fuel are completely dry before allowing them to tank flap, along with the tyre size and pres- retract.
  • Page 203 Checking and refilling levels Check that the fuel flap is correctly closed. If, as an emergency measure, you have to fill – The fuel tank is full as soon as the automat- ● the tank with petrol with a lower RON to that ic filler nozzle cuts out.
  • Page 204 Group Fuel Additives for petrol engines”. 590. If diesel fuel which meets European use only moderate engine speeds and a light These additives can be bought at SEAT deal- standard EN 590 is not available, the Cetane throttle. High engine speed and full throttle ers, where information on how to use them number (CZ) must, at minimum, be 51.
  • Page 205: Engine Compartment

    Even one tankful of diesel fuel that does ● knowledge required, let an authorised SEAT Always be aware of the danger of injury and not comply with the standard could damage dealer change fluids during service inspec-...
  • Page 206 Fluids of the correct specifications can be ● Pull the release catch in the direction of the – acquired from the selection of SEAT Original ››› Fig. 202 arrow and the bonnet will be Accessories.
  • Page 207: Engine Oil

    Checking and refilling levels Checking levels Fig. 204 Diagram for the location of the various elements. Engine oil From time to time, the levels of the different Overview fluids in the vehicle must be checked. Never You will find further explanations, instruc- fill with incorrect fluids, otherwise serious tions and restrictions on the technical speci- General notes...
  • Page 208 Advice performed by a technical service or special- top up (once) with oil for fixed service inter- ● Avoid mixing this oil with other engine oils. ›››  ised workshop. vals page 46 (up to a maximum of 0.5 Only in exceptional circumstances, if the ●...
  • Page 209: Coolant

    Checking and refilling levels Read the additional information carefully CAUTION CAUTION ›››  page 45 ● The oil level must never exceed area Do not mix engine oil with additives. Risk of The dipstick shows the engine oil level. ››› Fig.
  • Page 210: Brake Fluid

    ● sion tank when the engine heats up. Check the brake fluid level in the reservoir – gine to overheat, contact an authorised SEAT ››› Fig. 207. It should be between the “MIN” dealer immediately, as this could damage the CAUTION and “MAX”...
  • Page 211: Windscreen Washer

    Checking and refilling levels Windscreen washer there may be a leak in the brake system. If therefore recommend using clean water with the brake fluid level in the reservoir is too a glass cleaning product to eliminate any low, this will be indicated by the warning stubborn dirt (with an anti-freeze additive in topping up windscreen washer fluid winter).
  • Page 212: Battery

    ● If you frequently use the vehicle for short formed by an authorised SEAT dealer. trips, the battery may not fully charge and Open the battery cover in the direction indi- –...
  • Page 213 In vehicles equipped with a battery with col- 10% of the battery capacity to fully charge official SEAT technical service before the start our indicator, the so-called magic eye the battery. of winter.
  • Page 214 In vehicles fitted with the “Start-Stop” sys- We recommend having the battery changed tem, the charger cable cannot be directly con- by an authorised SEAT dealer, where the new nected to the negative terminal of the vehicle battery but must be attached to the engine battery will be correctly installed and the ›››...
  • Page 215: Wheels And Tyres

    We recommend having all work on tyres Do not use summer or winter tyres that are ● WARNING and wheels carried out by an authorised SEAT more than 6 or 4 years old respectively. dealer. ● During the first 500 km, new tyres do not ●...
  • Page 216 Advice Changing wheels indicators is given on the tyre sidewalls by which results in vibration of the steering the letters “TWI”, triangular symbols or other wheel. symbols. The wheel must be rebalanced if a new tyre is fitted or if a tyre is repaired. The useful life of the tyres depends primarily on the following factors: Incorrect wheel alignment...
  • Page 217: Spare Wheel

    190 km/h (118 mph) Spare wheel or tyres to those originally fitted by SEAT may be fitted, as well as the combinations al- 200 km/h (124 mph) lowed between the front axle (axle 1) and...
  • Page 218: Tyre Monitoring Systems

    Advice ››› The tyre pressure of the spare wheel must be ● Only use this spare wheel to reach the page 104 will light up and an audible checked (preferably whenever the tyre pres- nearest Official Service, as it is not designed warning will be heard.
  • Page 219: Winter Service

    Wheels and tyres The warning lamp  lights up the vehicle carefully with no severe braking For the sake of the environment or steering manoeuvres. If the pressure on at least one tyre is signifi- Summer tyres should be fitted again in time, cantly lower than the pressure set by the driv- ●...
  • Page 220: Technical Specifications

    Technical specifications Technical specifications Abbrevi- Meaning ation Technical specifications Revolutions per minute - engine speed. Newton metres, unit of engine torque. Important information litres per Fuel consumption in litres per 100 km (70 100 km miles). Important Carbon dioxide emissions in grams per km g/km (mile) travelled.
  • Page 221: Information On Fuel Consumption

    The carrying capacity must include: such as driving style, road conditions, traffic ● If you wish to calculate the exact weight of ● occupants, conditions, environmental conditions, load your vehicle please contact a SEAT dealer. » and number of passengers.
  • Page 222: Driving With A Trailer

    Technical specifications Calculation of fuel consumption In the interest of road safety, we recommend may affect vehicle handling and lead to an ac- that you always tow approaching the maxi- cident. Always adjust your speed and driving The consumption values have been calcula- mum drawbar load.
  • Page 223: Wheels

    Technical specifications Wheels low, there is an increased danger of accidents - particularly at high speeds. Tyre pressure, snow chains, wheel ● If the tightening torque of the wheel bolts is too low, they could loosen while the vehi- bolts cle is in motion.
  • Page 224: Engine Data

    Technical specifications Engine data Petrol engine 1.2 55 kW (75 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 55 (75)/5,400 112/3,750 3/1,198 Super 95 RON/Normal 91 RON Slight power loss. Performance Top speed (km/h) 175 (5)
  • Page 225 Technical specifications Petrol engine 1.2 TSI 63 kW (85 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 63 (85)/4,800 160/1,500-3,500 4/1,197 Super 95 RON/Normal 91 RON Slight power loss. Performance Top speed (km/h) 183 (5) Acceleration from 0-80 km/h (seconds)
  • Page 226 Technical specifications Petrol engine 1.2 TSI 66 kW (90 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 66 (90)/4,400-5,400 160/1,400-3,500 4/1,197 Super 95 RON/Normal 91 RON Slight power loss. Performance Top speed (km/h) 186 (5) Acceleration from 0-80 km/h (seconds)
  • Page 227 Technical specifications Petrol engine 1.2 TSI 77 kW (105 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 77 (105)/5,000 175/1,550-4,100 4/1,197 Super 95 RON/Normal 91 RON Slight power loss. Performance Top speed (km/h) 195 (5) Acceleration from 0-80 km/h (seconds)
  • Page 228 Technical specifications Petrol engine 1.6 77 kW (105 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 77 (105)/5,600 153/3,800 4/1,598 Super 95 RON/Normal 91 RON Slight power loss. Performance manual automatic Top speed (km/h) 193 (5)
  • Page 229 Technical specifications Petrol engine 1.2 TSI 81 kW (110 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 81 (110)/4,600-5,600 175/1,400-4,000 4/1,197 Super 95 RON/Normal 91 RON Slight power loss. Performance manual manual Ecomotive...
  • Page 230 Technical specifications Petrol engine 1.6 81 kW (110 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 81 (110)/5,800 155/3,800-4,000 4/1,598 Super 95 RON/Normal 91 RON Slight power loss. Performance manual automatic Top speed (km/h) 199 (5)
  • Page 231 Technical specifications Petrol engine 1.4 90 kW (122 PS) Automatic Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 90 (122)/5,000 200/1,500-4,000 4/1,390 Super 95 RON/Normal 91 RON Slight power loss. Performance Top speed (km/h) 206 (6) Acceleration from 0-80 km/h (seconds)
  • Page 232 Technical specifications Petrol engine 1.4 TSI 92 kW (125 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel 92 (125)/5,000-6,000 200/1,400-4,000 4/1,395 Super 95 RON/Normal 91 RON Slight power loss. Performance Top speed (km/h) 209 (6) Acceleration from 0-80 km/h (seconds)
  • Page 233 Technical specifications Diesel Engine 1.4 CR 66 kW (90 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel Diesel according to standard EN 590, min. 66 (90)/3,500 230/1,750-2,500 4/1,422 51 CN Performance manual manual...
  • Page 234 Technical specifications Diesel Engine 1.6 CR 66 kW (90 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel Diesel according to standard EN 590, min. 66 (90)/4,200 230/1,500-2,500 4/1,598 51 CN Performance manual automatic...
  • Page 235 Technical specifications Diesel Engine 1.6 CR 77 kW (105 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel Diesel according to standard EN 590, min. 77 (105)/4,400 250/1,500-2,500 4/1,598 51 CN Performance Ecomotive Top speed (km/h)
  • Page 236 Technical specifications Diesel Engine 1.6 CR 85 kW (115 PS) Power output in kW (PS) at rpm Maximum torque (Nm at rpm) No. of cylinders/displacement (cm Fuel Diesel according to standard EN 590, min. 85 (115)/3,500-4,000 250/1,500-3,000 4/1,598 51 CN Performance Top speed (km/h) Acceleration from 0-80 km/h (seconds)
  • Page 237: Dimensions

    Technical specifications Dimensions Dimensions Fig. 216 TOLEDO Front and rear projection (mm) 876/1,004 Wheelbase (mm) 2,602 Length (mm) 4,482 Front/rear track width (mm) 1,463/1,500 Width (mm) 1,715 Height at kerb weight (mm) 1,466 Turning radius (m) 10.2 This data will change depending on the type of wheel rim.
  • Page 239: Index

    Deactivation of front airbag ....75 folding down and raising the back seat back- ASR ........168 description .
  • Page 240 Climatronic ....... 41 seat belts ......199 Changing rear lights on the rear lid adjusting the temperature .
  • Page 241 Cruise control ......36, 176 rear seat armrest ..... . . 137 Jump leads .
  • Page 242 G 12 plus-plus ......46 Front seat topping up ......208 heating .
  • Page 243 Index Fuses ........84 Head-protection airbags distance travelled .
  • Page 244 Index coming home and Leaving Home ..127 net pocket ......140 Daytime running lights .
  • Page 245 Refuelling ....... 200 seat belts ......71 opening tank flap .
  • Page 246 ......153 Seat belts ....... . 67 Tightening torque of wheel bolts .
  • Page 247 ......197 Unfastening the seat belt ....14 service position .
  • Page 248 Windscreen washer ......47 seat belt ......67, 100 headlight washers .
  • Page 249 SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to under- stand, that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason no right at all may derive based on the data, drawings and descriptions in this current handbook.

Table of Contents