Page 1 auto emoción...
Page 3 Foreword This owner's manual and the corresponding supplements should be read carefully to familiarise yourself with your vehicle. Also, the regular care and maintenance and correct handling of the vehicle will contribute to preserve its value. For safety reasons, note the information concerning accessories, modifications and parts exchange. If selling the vehicle, give all of the onboard documentation to the new owner as this should be kept with the vehicle.
Page 5: Table Of Contents
Driving economically and with respect for the Rear seat bench ......environment ......
Page 6 Contents Technical Data Trailer towing ........... . Instructions to follow .
Page 7: The Structure Of This Manual
The structure of this manual The structure of this manual Before reading this manual it must be understood Caution This manual contains a description of the equipment supplied with the Texts with this symbol draw your attention to a possible risk of damage to vehicle at the time of going to press.
Page 8: Content
(e.g. “Air conditioning”). The entire manual is divided into five large parts which are: 1. Safety First Information on the vehicle equipment relating to passive safety such as seat belts, airbags, seats, etc. 2. Controls and equipment...
Page 9: Safety First
The This chapter contains important information, tips, suggestions and following list includes most of the safety equipment in your SEAT: warnings that you should read and follow in the interest of your own •...
Page 10 – Never drive when your driving ability is impaired (e.g. by medica- – Make sure that no objects can interfere with the pedals. tion, alcohol, drugs). – Adjust front seat, head restraint and mirrors properly for your – Observe traffic laws and speed limits. size.
Page 11 Safe driving – Always reduce your speed as appropriate for road, traffic and weather conditions. – When travelling long distances, take breaks regularly - at least every two hours. – If possible, avoid driving when you are tired or are under pres- sure of time.
Page 12 ⇒ fig. and steering wheel – Move the driver's seat forwards or backwards so that you are able to press the accelerator, brake and clutch pedals to the floor with your knees still slightly angled ⇒ – Ensure that you can reach the highest point of the steering wheel.
Page 13: Safe Driving
The further the backrests are tilted to the rear, the greater the risk...
Page 14 • If the passengers on the rear seat are not sitting properly, they could rest them on the instrument panel, out the window or on the seat. An incor- sustain severe injuries. rect sitting position exposes you to an increased risk of injury in the event •...
Page 15 Vehicle occupants are pressed into their seats during a rear end collision. The resulting body pressure on the backrest activates the crash-active head restraint* on the front seat, which moves rapidly forwards and upwards at the same time. This movement reduces the distance between the occupant's head and the head rest, thus reducing the risk of head injuries such as brain trauma.
Page 16 (e.g. by “falling” back into the seat when entering the vehicle) or if pressure is applied to a front seat head restraint from the rear. This accidental activation is, however, not dangerous as the crash-active head restraints will return to the original position immedi- Fig.
Page 17 • • never kneel on the seats, Do not swap the centre rear head restraint with either of the outer seat • never tilt your backrest far to the rear, rear head restraints. •...
Page 18: ⇒ Page 10, "Proper Sitting Position For Occupants
If a brake circuit fails, the brake pedal must be free to move further than • normal in order to bring the vehicle to a stop. never travel on a seat without wearing the seat belt, • never carry any person in the luggage compartment.
Page 19: Stowing Luggage
Safe driving WARNING (continued) WARNING (continued) • • Never lay or fit floor mats or other floor coverings over the original floor Always stow objects in the luggage compartment and secure them on mats. This would reduce the pedal area and could obstruct the pedals. Risk the fastening rings.
Page 20 • Never secure a child seat on the fastening rings. Fastening rings There are four fastening rings in the luggage compartment which can be used to secure luggage and other objects.
Page 21: Seat Belts
Children must be protected with an appro- priate child restraint system. WARNING • If the seat belts are worn incorrectly or not at all, the risk of severe inju-  ries increases. Seat belt warning lamp* •...
Page 22  The warning lamp* does not go out until the driver seat belt is fastened while the ignition is switched on. Depending on the model version...
Page 23: Why Wear Seat Belts
25 km/h to 50 km/h, for example, the kinetic energy increases by a factor of four. Because the passengers in our example are not restrained by seat belts, the entire amount of kinetic energy has to be absorbed at the point of impact ⇒...
Page 24 It is also important for the rear passengers to wear seat belts properly, as they could otherwise be thrown forward violently in an accident. Rear passengers who do not use seat belts endanger not only themselves but also the front ⇒...
Page 25 • If the seat belts are worn incorrectly or not at all, the risk of severe inju- Our examples describe frontal collisions. Of course, properly worn seat belts ries increases. The optimal protection from seat belts can be achieved only reduce substantially the risk of injury in all other types of accidents.
Page 26: Safety Belts
• position by a latch. Do not allow the seat belt to be damaged or jammed, or to rub on any sharp edges. • Never wear the seat belt under the arm or in any other incorrect posi- tion.
Page 27 • Never put the latch plate in the buckle of another seat. If you do this, the seat belt will not protect you properly and the risk of injury is increased.
Page 28 An incorrectly worn seat belt web can cause severe injuries in the event of an accident. • The shoulder part of the seat belt must lie on the centre of the shoulder, never across the neck. The seat belt must lie flat and snugly on the torso ⇒ page 25, fig.
Page 29 • WARNING For pregnant women, the lap part of the seat belt must lie as low as possible over the pelvis, never across the stomach, and always lie flat so Never unbuckle a seat belt while the vehicle is in motion. If you do, you that no pressure is exerted on the abdomen.
Page 30: Belt Tension Devices
The seat belts for the front occupants are equipped with belt tension devices. Sensors will only trigger the belt tension devices during severe head-on, lateral and rear collisions, and only if the seat belt is actually being worn. This Incorrectly fastened seat belts retracts and tightens the seat belts, reducing the forward motion of the occu- pants.
Page 31 The belt tension device and seat belt including its automatic retractor cannot be repaired. • Any work on the belt tension devices and seat belts, including the removal and refitting of system parts in conjunction with other repair work, must be performed by a qualified workshop only.
Page 32: Airbag System
The airbag deploys in fractions of a second and with a high velocity. If you • If you are not wearing a seat belt or if you lean forward or to the side or have assumed an incorrect seating position at that moment, you could assume an incorrect sitting position, the risk of injury is increased sustain critical injuries.
Page 33 An enabled front airbag on the front passenger side is potentially a major − Follow the installation instructions of the child seat manufacturer danger to a child. The front passenger seat is life threatening to a child if you and absolutely observe the warnings ⇒ page 46, “Child safety”.
Page 34 Airbag system Repair, care and disposal of the airbags Monitoring of airbag and belt tension device system The functionality of the airbag and belt tension device system is constantly monitored electronically. Each time the ignition is switched on, the warning The parts of the airbag system are installed in various places in your vehicle.
Page 35 Airbag system WARNING (continued) • We urgently recommend that you go to a qualified workshop for all work on the airbag system. • Never attempt to alter the front bumper or the body. • The airbags provide protection for one accident only, if they have been deployed they must be replaced.
Page 36: Front Airbags
The airbag system is not a substitute for seat belts, but is an integral part of the vehicle's overall passive safety system. Please bear in mind that the airbag system can only work effectively when the occupants are wearing their seat belts correctly and have adjusted the head restraints properly.
Page 37 • or if the vehicle rolls. WARNING • The seat belts and airbags can only provide maximum protection if the occupants are seated correctly ⇒ page 10, “Proper sitting position for occupants”. • If a fault should occur in the airbag system, have the system checked immediately by a qualified workshop.
Page 38 Airbag system In order to provide the desired extra protection in an accident, the airbags may develop when the airbag deploys. This is normal and is no indication have to deploy extremely rapidly (within fractions of a second). A fine dust that there was a fire in the vehicle.
Page 39: Side Airbags
• If you are not wearing a seat belt or if you lean forward or to the side or assume an incorrect sitting position, the risk of injury is increased substantially. This increased risk of injury will be further increased if you are struck by an inflating airbag.
Page 40 • Never drive if the interior door panels have been removed or if the The airbag system is not a substitute for seat belts, but is an integral part of panels have not been correctly fitted. the vehicle's overall passive safety system. Please bear in mind that the •...
Page 41 Airbag system Function of side airbags The special design of the airbag allows the controlled escape of the propel- lant gas when an occupant puts pressure on the bag. Thus, the head and Inflated airbags can reduce the risk of head or chest injury in chest are surrounded and protected by the airbag.
Page 42 Any work on the side airbag system or removal and installation of the If you do not wear a seat belt, if you lean forward, or are not seated airbag components for other repairs (such as removal of the front seat) correctly while the vehicle is in motion, you are at greater risk of injury should only be performed by a qualified workshop.
Page 43: Curtain Airbags
(airbags with gas generator) for the driver, front curtain airbag system”. passenger and passengers on the rear seats, • The airbag system is not a substitute for seat belts, but is an integral part of in the dash panel insert ⇒ page 31.  a warning lamp the vehicle's overall passive safety system.
Page 44 WARNING • In order for the side airbags to provide their maximum protection, the prescribed sitting position must always be maintained with seat belts fastened while travelling. • Fig. 25 Deployed curtain...
Page 45 Airbag system WARNING (continued) • There must be no other persons, animals or objects between the occu- pants of the outer seats and the deployment space of the curtain airbags so that the curtain airbag can deploy without restriction and provide the greatest possible protection.
Page 46: Deactivating Airbags
Airbag system Deactivating airbags* Disabling front passenger airbag If you fit a rear-facing child seat to the front passenger seat, the front passenger airbag must be de-activated. Fig. 27 Warning lamp for deactivated passenger airbag in centre console When the passenger airbag is deactivated, this means that only the frontal airbag is deactivated.
Page 47 • As soon as the child seat is no longer needed on the front passenger seat, enable the front passenger airbag again. • Only deactivate the passenger airbag when the ignition is off, other-...
Page 48: Child Safety
We recommend that children under 12 years of age be transported on the rear seats. Children travelling on the rear seat must use a child restraint system or As the driver, you are responsible for any children you transport in the seat belts provided, depending on their age, height and weight.
Page 49 Never allow a child to be transported in a vehicle without being properly secured, or to stand up or kneel on a seat while travelling. In an accident, the child could be flung through the vehicle, causing possibly fatal injuries to themselves and other occupants.
Page 50: Child Seats
Child seats that have been tested and approved under the ECE R 44 standard Group 0: For babies from about 9 months old and 10 kg in weight the most bear the test mark on the seat (the letter E in a circle with the test number ⇒ fig.
Page 51 Children under 7 years of age weighing between 15 and 25 kg are best use in the vehicle wallet and always keep them in the vehicle. protected by group 2 child seats in conjunction with properly adjusted seat belts. WARNING...
Page 52 The shoulder part of the seat belt must lie approximately on the centre of the shoulder, never across the neck or the arm. The seat belt must lie close to the torso. The lap belt part must lie across the pelvis, not across the stomach, and always fit closely.
Page 53: Securing Child Seats
Securing child seats Ways to secure a child seat A child seat can be secured differently on the rear seat and on the front passenger seat. • You can secure a child seat to the rear seat or front passenger seat in the Child seats in groups 0, 0+ y 1 with the “ISOFIX”...
Page 54 Securing the child seat by “ISOFIX” and “Toptether” Two “ISOFIX” retaining rings are fitted on each rear seat. In some vehicles, the rings are secured to the seat frame and in others they are secured to the rear systems or anti-rotating system.
Page 55 Safety First Operating instructions Tips and Maintenance Technical Data...
Page 56 Fig. 32 Instrument panel...
Page 57: Operating Instructions
Some of the items of equipment listed here are fitted only on certain Thumb wheel for left seat heating ..... . .
Page 58: Instruments
Cockpit Instruments Instrument overview The instruments display the vehicle operating status. Fig. 33 Detailed view of dash panel instrument panel Detailed view of dash panel instrument panel Fuel gauge ⇒ page 57 Multi-function display Engine coolant temperature gauge ⇒ page 57 Rev counter ⇒...
Page 59 Cockpit   Fuel gauge and reserve indicator Engine coolant temperature display This gauge shows the engine coolant temperature. Fig. 34 Instrument panel: Fig. 35 Instrument panel: fuel gauge engine coolant tempera- ture gauge Instrument panel: fuel gauge The fuel tank has a capacity of approx. 55 litres. Needle in cold zone ⇒...
Page 60 Cockpit display . Stop the car and switch off the engine. Check the coolant level ⇒ page 219 ⇒ For the sake of the environment Changing up a gear early will help you to save fuel and minimise engine Even if the coolant level is correct do not continue driving. You should obtain noise.
Page 61: Digital Display In The Instrument Panel
Cockpit Digital display in the instrument panel Display (without warning or information texts) The display in the instrument panel shows, amongst other things, the mileage and trip recorder as well as the selector lever position. Fig. 37 Detail of the instrument cluster: screen with Tiptronic gear indi- cator...
Page 62 Cockpit Displayed categories Distance display or flexible service interval display: “Distance display or flexible service interval display” The display in the instrument panel shows the mileage and Selector lever position display for the automatic gearbox. The actual trip recorder as well as the selector lever position. position of the selector lever or the gear which is engaged (for Tiptronic) are highlighted.
Page 63 Cockpit An overdue service is indicated by a minus sign in front of the mileage or day information. Display with multi-function display (MFD)* The multi-function display (MFD) shows you diverse journey and consumption data. Fig. 40 Digital instru- ment panel display: average fuel consumption indicator The multi-function system uses two automatic memories: 1 - Actual...
Page 64 Cockpit the existing trip recorder memory. The memory will automatically be deleted if the journey is interrupted for more than two hours. The total journey memory 2 collects the journey data for any number of indi- vidual journeys (even if the ignition is switched off for longer than two hours) up to a total of 99 hours and 59 minutes travel time, 9999 kilometres distance travelled and 999 litres of fuel consumed.
Page 65 Cockpit Set speed indicator ltr/100km or ltr/hr - Current fuel consumption When driving at the required speed, enter the speed indicator mode and The display will show the current fuel consumption in litre/km whilst the press the button (Reset), the display remembers the indicated speed. If vehicle is in motion or in litre/hour when the vehicle is in a stationary position the indicated speed is exceeded, a warning text is displayed on the screen with the engine running.
Page 66 Cockpit cated by symbols with warnings and information texts in the display. An Examples of priority 1 warning reports (red) • audible warning is given in certain cases.  Brake system symbol with warning text STOP BRAKE FLUID INSTRUCTION MANUAL or STOP BRAKE FAULT INSTRUCTION MANUAL. Warning symbols •...
Page 67: Instrument Panel Menus
Cockpit Instrument panel menus Main menu The menu enables access to the different display functions. Fig. 43 Windscreen wiper lever: button A to confirm the menu selection and Fig. 44 Digital instru- rocker switch B to change ment panel display: Main the menu menu Open main menu...
Page 68 Cockpit Main menu Function Multi-function display Change to the multi-function display (MFD): “Multi-function display (MFD)” Audio The current station will be shown when the radio is switched on. Navigation This menu is only available if the vehicle is fitted with a navigation system. The navigation system must be switched on.
Page 69 Cockpit Example of menu use All the menus on the instrument panel may be used according to the following procedure. Fig. 45 Windscreen wiper lever: button A to confirm the menu selection and Fig. 46 Digital instru- rocker switch B to change ment panel display: the menu winter tyres indicator...
Page 70 Cockpit 5. To activate and deactivate the speed limit warning 6. To close the menu “Winter tyres” – Use the rocker switch to select the menu point On/ Off and press – In the menu select Back. the button to switch the speed warning either on or off. If the speed warning is deactivated, three dashes will be displayed --- The function “Winter tyres”...
Page 71 Cockpit Vehicle status menu Priority 2 warning messages and information texts: “Information and warning messages on the screen” will automatically disappear from the screen after a This menu shows warning or information texts time and will be stored in the “Vehicle status” menu. The warning and information texts may be viewed in this menu.
Page 72 Cockpit Lights & visibility From this menu it is it possible to alter the vehicle lighting settings: “Lights and visibility Menu”. Display off Only emergency messages appear Back This returns to the main menu Note For electronic and vehicle equipment one or more of these menus will be displayed.
Page 73 Cockpit Note For electronic and vehicle equipment one or more of these menus will be displayed. Lights and visibility menu From this menu it is it possible to alter the vehicle lighting settings. Open Lights and visibility Menu – Select the option Lights & visibility from the menu and press button on the windscreen wiper lever.
Page 74: Warning Lamps
Cockpit Warning lamps Overview of the warning lamps The warning lamps indicate a number of different functions and possible faults. Fig. 47 Instrument panel with warning lamps. Some of the items of equipment listed here are fitted only on certain models/model years or are optional extras.
Page 75 Cockpit Item Symbol Meaning of warning and control lamps Further information  ⇒ page 75 Fuel level / reserve  ⇒ page 75 Coolant level / coolant temperature  ⇒ page 76 Rear fog light switched on   ⇒ page 76 Turn signals in operation ...
Page 76 Cockpit Item Symbol Meaning of warning and control lamps Further information  ⇒ page 19 Fasten seat belts!  ⇒ page 80 Tyre pressure  ⇒ page 81 Engine fault (petrol engine) Glow plug system for diesel engine  ⇒ page 81...
Page 77 Cockpit The instrument panel displays shows the following message : PLEASE WARNING REFUEL! • Failure to observe warning lamps and warning messages can result in serious personal injury or damage to your vehicle. •  The risk of an accident increases if your vehicle breaks down. Use a Coolant Level* / temperature warning triangle to draw the attention of other road users to your stationary vehicle so that it does not represent a danger.
Page 78 Cockpit   Turn signals Coolant level too low The instrument panel displays shows the following message : STOP CHECK The warning lamp flashes when the turn signals are in oper- COOLANT INSTRUCTION MANUAL ⇒ page 219. ation. First look at the coolant temperature gauge. If the needle is in the normal range, top up with coolant at the earliest opportunity ⇒...
Page 79 Cockpit   Bulb defect Brake system* / handbrake The warning lamp lights up when a bulb in the vehicle's exte- The warning lamp lights up if the handbrake is applied, if the rior lighting is defective. brake fluid level falls too low or if there is a fault in the brake system.
Page 80 Cockpit There is a fault in the ABS if: WARNING (continued) •  The warning lamp does not light up when the ignition is switched on. • •  If the brake warning lamp lights up together with the ABS warning The warning lamp does not go out again after a few seconds.
Page 81 Cockpit  Differential lock fault (EDL)* If the lamp does not switch off, bring the vehicle to a specialised workshop to repair the fault. EDL operates along with the ABS in vehicles equipped with an Electronic Stabilisation Program (ESP)* WARNING •...
Page 82 Cockpit  Tyre pressure* Tyre pressure adjustment Following the modification to tyre pressure or changing one or more wheels, ⇒ fig. 48 the button must be kept pressed while the ignition is on until an acoustic signal is heard. If the wheels are under excessive load (for example, driving with a trailer or heavy load), the tire pressure must be increased to the recommended value for a full load (see the sticker on the inside of the fuel flap).
Page 83 Cockpit   Engine management* Emission control system* This warning lamp monitors the engine management system This warning lamp monitors the exhaust system. for petrol engines.  Warning lamp flashes:  The warning lamp (Electronic Power Control) lights up when the ignition When there is misfiring that can damage the catalytic converter.
Page 84 Cockpit • It will light up continuously if the ESP is switched off. engine is off (for example, for towing). You should take into account that you • will need considerably more power than normal to steer the vehicle if the It will also come on if a fault should occur in the ABS because the ESP steering assistance is reduced or has failed completely.
Page 85 ⇒ page 163. The engine can, however, be started if the appropriate coded SEAT genuine key is used. Note The vehicle cannot be operated properly if you do not have a genuine SEAT key. Depending on the model version Safety First...
Page 86: General Points
Steering wheel controls Steering wheel controls • General points Audio version, to control the available audio functions from the steering wheel. • Audio + Telephone version, to control the available audio functions and The steering wheel includes a multifunction module from where it is possible the telephone system from the steering wheel.
Page 87 Steering wheel controls Short press Long press Button Radio CD Audio Radio CD Audio CD mp3 CD mp3 Volume up Continue volume up Volume down Continue volume down Station search. Station search. Higher fre- Following track Higher fre- Fast forward quency.
Page 88 Steering wheel controls Steering wheel Audio + Telephone version controls Fig. 51 Controls on the Fig. 52 Controls on the steering wheel steering wheel Short press Long press Button Radio CD Audio Radio CD Audio CD mp3 CD mp3 Volume up Continue volume up Volume down Continue volume down...
Page 89 Steering wheel controls Cyclic source control No specified function FM - AM - CD - CDC - FM... Voice recognition activation No specified function Press to speak Make a call Direct access to the phone book No specified function Accept a call Terminate call Refuse call No specified function...
Page 90: Radio Navigation System
Steering wheel controls Radio navigation system Steering wheel audio version controls Fig. 53 Controls on the Fig. 54 Controls on the steering wheel steering wheel Short press Long press Button Radio Radio CD mp3 CD mp3 Increase the source volume and the navigation message Increase the source volume and the navigation message continuously Decrease the source volume and the navigation message Decrease the source volume and the navigation message continuously...
Page 91 Steering wheel controls Station search. Station search. Lower Previous track Lower Rewind frequency frequency Cyclic change of source Repeat the last Navigation instruction Radio - CD / CDC - Radio - ... When in Navigation mode the system leaves the navigation screen. Only if the Navigation function is activated.
Page 92 Steering wheel controls Steering wheel Audio + Telephone controls Fig. 56 Steering wheel Fig. 55 Controls on the Audio + Telephone steering wheel controls Short press Long press Button Radio Radio CD mp3 CD mp3 Increase the source volume and the navigation message Increase the source volume and the navigation message continuously Decrease the source volume and the navigation message Decrease the source volume and the navigation message continuously...
Page 93 Steering wheel controls Cyclic change of source Repeat the last Navigation instruction Radio - CD / CDC - Radio - ... Only if the Navigation function is activated. When in Navigation mode the system leaves the navigation screen. Voice recognition activation No specified function Press to speak Make a call...
Page 94: Steering Wheel Lighting Controls
Steering wheel controls Steering wheel lighting controls The lighting is turned on using the simultaneous pressing of the following keys: Push simultaneously... ⇒ fig. 58 Audio Audio + Telephone ⇒ fig. 57 Fig. 57 Steering wheel Audio + Telephone version controls Fig.
Page 95: Central Locking
Unlocking and locking Unlocking and locking Central locking Safety system “Safe” This is an anti-theft device consisting of a double lock for the Description door locks and a deactivation function for the boot in order to make forced entry more difficult. The central locking system enables you to lock and unlock all the doors and the tailgate from one point.
Page 96 Unlocking and locking When the “Safe” system is deactivated, the doors are locked using the simple WARNING locking system, meaning that they may be opened from the interior but not from the exterior. No one should remain in the vehicle if the “Safe” deadlock mechanism has been activated.
Page 97 Unlocking and locking will be activated. The indicator will be turned off as will be the alarm for those Unlocking vehicles fitted with one. The driver's door automatically unlocks when the key is removed from the ignition. Unlocking the boot See ⇒...
Page 98 Unlocking and locking Emergency manual locking Unlocking the manually (emergency) locked driver's door Insert the key in the door lock cylinder and rotate anti-clockwise for the left This permits mechanical locking of the doors in case of hand side doors and clockwise for the right hand side doors. central locking system failure.
Page 99 Unlocking and locking • Central locking button The driver or front passenger door cannot be locked if it is open. This prevents you from locking yourself out of the vehicle. • The vehicle can be locked and unlocked from the inside using Repeated operation of the central locking will deactivate the central the central locking button.
Page 100 Unlocking and locking Childproof locks This function is independent of the electronic opening and locking systems of the vehicle. It only affects the rear doors. It is only The childproof lock prevents the rear doors being opened possible to activate it and deactivate it manually, as described from the inside.
Page 101: Keys
Unlocking and locking Keys If you sell the vehicle, please give the plastic key tab to the new owner. Duplicate keys If you need a replacement key, take your key tab to an Authorised Service Key set Centre. The set of keys includes a remote control, a key without a remote control and a key tab with the number of the key.
Page 102: Radio Frequency Remote Control
Unlocking and locking Radio frequency remote control Locking and unlocking the vehicle The remote control key can be used to lock and unlock the vehicle from a distance. Fig. 65 Range of the remote control ⇒ fig. 64 Using the button (arrow) on the control, the key shaft is released.
Page 103 Unlocking and locking Changing the battery WARNING • If the battery indicator does not flash when the buttons are pushed, the Incorrect use of the key can result in critical injuries. • battery must be replaced. Never leave children or disabled persons in the vehicle; in case of emer- gency they may not be able to leave the vehicle or look after themselves.
Page 104: Anti-Theft Alarm System
Unlocking and locking  – Operate the button once for locking on the remote control, the When does the system trigger an alarm? indicators will flash. The system triggers an alarm if the following unauthorised actions are carried out when the car is locked: –...
Page 105 Unlocking and locking Note WARNING • • If, after the alarm goes off, access is gained to a second secured zone The “safe” security system remains deactivated if the volumetric (e.g. the tailgate is opened after a door has been opened), the warning signal sensor is deactivated.
Page 106: Tailgate
Unlocking and locking Tailgate Opening and locking The operation of the tailgate opening system is electric. It is activated by using the handle on the tailgate Fig. 67 Detail of the inside of the tailgate: hand grip Opening the tailgate ⇒...
Page 107 Unlocking and locking Emergency opening WARNING • This allows the vehicle to be opened if the central locking Always close the tailgate properly. Risk of accident or injury. • does not operate (for example if the battery is flat) The tailgate must not be opened when the reverse or rear fog lights are lit.
Page 108: Windows
Unlocking and locking Windows Buttons in the driver door Button for window in front left door Button for window in front right door Opening or closing the windows electrically Buttons for rear windows* The front and rear electric windows can be operated using the Safety switch for deactivating the electric window buttons in the rear controls in the driver's door.
Page 109 Unlocking and locking ⇒ page 106, fig. 69 The buttons have two levels for opening the WARNING (continued) window and two for closing it. This makes it easier to open or close windows • to the desired position. If necessary, use the safety switch to disable the rear electric windows. Make sure that they have been disabled.
Page 110: Sliding/Tilting Roof
Unlocking and locking Using the remote control WARNING – Push the lock button on the remote control for about 3 seconds. • Incorrect use of the electric windows can result in injury. All windows which function electrically will be either opened or •...
Page 111 Unlocking and locking Closing the sliding/tilting sunroof WARNING (continued) ⇒ page 108, fig. 70 ⇒ – Turn the rotary button to position • Never leave children or disabled persons in the vehicle, particularly if they have access to the keys. Unsupervised use of a key could mean that Opening/tilting the sliding/tilting sunroof the engine is started or that electrical equipment is used (e.g.
Page 112 Unlocking and locking Roll-back function of the sliding/tilting roof* prevent fingers getting pinched against the roof opening. The sliding/tilting sunroof stops and opens again immediately if it is obstructed when closing. If the sliding/tilting roof has been opened again by the roll-back function, it can be closed only by pressing the rotary button at the front in position ⇒...
Page 113: Lights And Visibility
Lights and visibility Lights and visibility Lights Switching on the fog lights*   – Pull the switch out of position to the first stop. The  symbol in the light switch lights up.  Switching lights on and off Switching on the rear fog lights (vehicles with front fog lights) ...
Page 114 Lights and visibility • If the coming home* feature is activated, the acoustic signal for the Deactivation dipped beam headlights will not sound, it will sound if the position lights are – Turn the control to position 0. activated. • The rear fog light is so bright that it can dazzle drivers behind you.
Page 115 Lights and visibility • Do not put stickers on the windscreen in front of the sensor. This may Leaving home function* cause disruptions or faults in the automatic lighting system. The function is activated when the vehicle is unlocked using the remote control.
Page 116 Lights and visibility Instrument and switch lighting / Headlight range control Dynamic headlight range control Vehicles with gas discharge lamps (“xenon lamps”) are equipped with dynamic headlight range control. This means that the headlights will be adjusted to suit the load level of the vehicle and “nodding movements” when pulling off and braking are automatically compensated for.
Page 117 Lights and visibility 5. On a manual gearbox engage 1st gear, and for an automatic Note move the selector lever to P. The system operates from a speed of about 10 km/h. 6. Use the warning triangle to draw the attention of other road users to your vehicle.
Page 118 Lights and visibility Switching on the turn signals Note ⇒ fig. 78 – Move the lever all the way up to indicate right, and • The battery will run down if the hazard warning lights are left on for a long all the way down to indicate left.
Page 119: Interior Lights
Lights and visibility Interior lights WARNING The main beam can dazzle other drivers. Risk of accident! Never use the Front interior light type 1 main beam headlights or the headlight flasher if they could dazzle other drivers. Note • The turn signals only work when the ignition is switched on. The corre- ...
Page 120 Lights and visibility  Interior light switched on Note  Push the switch to the position If not all the vehicle doors are closed, the interior lights will be switched off Interior light switched off O after approx. 10 minutes, providing the key has been removed and the cour- ⇒...
Page 121 Lights and visibility  Front reading lights Switching off the reading lights Press the corresponding button to switch off the reading light. Rear interior and reading lights* Fig. 81 Interior roof trim: front reading lights, type Fig. 83 Interior roof trim: rear interior lights and reading lights.
Page 122: Visibility
Lights and visibility light turns off about 20 seconds after the closure of the doors. The interior The sun visors for the driver and the front passenger can be pulled out of their ⇒ fig. 84 lights are switched off when the vehicle is locked or when the ignition is mountings in the centre of the vehicle and turned towards the doors switched on.
Page 123: Windscreen Wipers
Lights and visibility Windscreen wipers – Move the control to the left or right to set the length of the intervals. Control to the left: long intervals; control to the right: short intervals. Four wiper interval stages can be set using switch ...
Page 124 Lights and visibility • When the “intermittent wipe function” is on, the intervals are directly WARNING proportional to the speed. This way, the higher the vehicle speed the shorter • the intervals. Worn and dirty wiper blades obstruct visibility and reduce safety levels. •...
Page 125 Lights and visibility Rain sensor* Switching on the rain sensor ⇒ fig. – Move the windscreen wiper lever into position The rain sensor controls the frequency of the windscreen wiper intervals, depending on the amount of rain. – Move the control to the left or right to set the sensitivity of the rain sensor.
Page 126 Lights and visibility  Rear window wiper Switching on the windscreen wiper and washer system ⇒ fig. – Press the lever fully forwards to position 88. The wash The windscreen wiper lever operates the windscreen wiper function will start immediately and the wiper will start with a and the wash and wipe system for the rear window.
Page 127: Mirrors
Lights and visibility Headlight washer system Automatic anti-dazzle interior mirror* The headlight washers clean the headlight lenses. The automatic anti-dazzle function can be switched on and off as desired. The headlight washers are activated automatically when the windscreen washer is used and the windscreen wiper lever is pulled towards the steering wheel for at least 1.5 seconds –...
Page 128 Lights and visibility 2. Turn the rotary knob to position the mirror so that you have a Note good view to the rear of the vehicle. • The automatic anti-dazzle function will only work properly if the sun 3. Turn knob to position R (right exterior mirror). blind* for the rear window is retracted and there are no other objects preventing light from reaching the interior mirror.
Page 129 Lights and visibility 2. Turn the rotary knob to position the mirror so that you have a good view to the rear of the vehicle. The right exterior mirror will be adjusted at the same time (synchronised). WARNING • The rear view convex or aspheric mirror increase the field of vision however the objects appear smaller and further away in the mirrors.
Page 130: The Importance Of Correct Seat Adjustment
Always keep your feet in the foot well when the vehicle is moving; never Proper seat adjustment optimises the level of protection rest them on the dash panel, out of the window or on the seat. This also offered by seat belts and airbags.
Page 131: Head Restraints
Fig. 92 Side view: head restraints and seat belts correctly adjusted – Adjust the head restraint so that its upper edge is at the same level as the top of your head, or as close as possible to the same level as the top of your head and, as a very minimum at eye level ⇒...
Page 132 Seats and stowage Removing or adjusting head restraints – To lower the head restraint, press the button and push head restraint downwards. The head restraints can be adjusted by moving them up and – Make sure that the head restraint engages securely in one of its down.
Page 133: Front Seats
⇒ fig. 94 The control elements in are mirrored for the front right- tilted far to the rear. The maximum protection of the seat belt can be hand seat. achieved only when the backrests are in an upright position and the driver and front passenger have properly adjusted their seat belts.
Page 134: Rear Seat Bench
The seat heating is switched off in the 0 position. The seat heating only works when the ignition is switched on. The left thumb wheel controls the left seat and the right thumb wheel the right seat.
Page 135 In this position the back rest is locked. This is the reason why the loop located • on the side of the seat must be pulled in the direction of the arrow to open the Adjust the seat only when the vehicle is stationary. Otherwise your seat backrest.
Page 136: Stowage Compartments
• After locking the seat backrest into position ensure that the seat belts protrude from the seat.
Page 137 There is a stowage area in the armrest. The CD changer is located in this compartment. Stowage areas under the front seats* There is a stowage locker with a cover under each front seat. Fig. 101 Front armrest with stowage area –...
Page 138 Danger of scalding. Folding table* Folding tables are fitted to the rear of the front seat backrests. Caution When driving, do not leave open cans in the cup holders. The drink might be spilt on braking, for example, and could damage the vehicle.
Page 139 Seats and stowage – Press the button on the cover to open these compartments ⇒ page 136, fig. 104. The cover will then open. – To close the cover, press it up until it engages. WARNING Always keep the stowage area cover closed while the vehicle is in motion to reduce the risk of injury during a sudden braking manoeuvre or in the event of an accident and to prevent any items from being thrown through the vehicle interior.
Page 140 Seats and stowage Luggage compartment retaining net Other stowage areas There is a retaining net in the luggage compartment for Other stowage areas can be found: securing objects. • in the centre console, • in the door trims (front and rear), •...
Page 141 Seats and stowage Drinks holders at the front Rear drink holder*/ Armrest* Fig. 108 Front drink Fig. 109 Opening the holder rear drink holders In the centre console, in front of the gear lever, there are two drink holders ⇒ fig. 108.
Page 142 Multi-purpose* mobile stowage compartment - Fitting and Fitting mobile stowage compartment removal – Fold down the small section of the rear seat back rest, in order to access the large section of the back rest. This stowage compartment may only be placed in the central area of the rear seat –...
Page 143 ⇒ page 140, fig. 111 – Pull each of the buttons on the clips (red buttons) forwards, until they snap out of place. – Fold the larger seat down and remove the mobile stowage compartment mounting plate. Fig. 113 Mobile stowage compartment Opening Fig.
Page 144 Seats and stowage Opening WARNING (continued) ⇒ page 141, fig. – Lift the cover , in area 113. • When the vehicle is moving, keep the tables stored inside the mobile stowage compartment with the cover closed, and likewise when they are Closing not in use.
Page 145: Ashtrays*, Cigarette Lighter* And Electrical Sockets
Seats and stowage Ashtrays*, cigarette lighter* and electrical Cigarette lighter* sockets Ashtray* Fig. 116 The cigarette lighter is located in the electric socket on the front of the centre console ⇒ fig. 116 to activate it ⇒ – Press on the cigarette lighter Fig.
Page 146 Seats and stowage Electrical sockets Note • Electrical equipment can be connected to any of the 12 volt Using electrical appliances with the engine switched off will drain the battery. sockets. • Before using any electrical accessories, see the instructions on ⇒...
Page 147 Seats and stowage ® AUX RSE connection* Apple* iPod connector ® The iPod connection is located in the centre arm rest. Fig. 119 AUX RSE connection Fig. 120 iPod connection in central armrest compartment. This connector may be used as an audio input (red and white connectors) or audio and video connector (red, white and yellow connectors).
Page 148: First-Aid Kit, Warning Triangle, Fire Extinguisher
Seats and stowage USB* Connection First-aid kit, warning triangle, fire extinguisher Inside the central armrest compartment there is a USB port. Warning triangle Fig. 121 USB connec- tion* in central armrest compartment Fig. 122 Warning triangle storage under the For information concerning the use of this equipment, please see the Radio rear cover handbook.
Page 149: Luggage Compartment
Seats and stowage Luggage compartment The warning triangle is located in a stowage box under the luggage compart- ⇒ page 146, fig. ment cover 123. To open this storage compartment, turn the knob 90° fig. Stowing luggage Note All luggage must be securely stowed. •...
Page 150 Seats and stowage Caution Hard objects on the shelf could chafe against the wires of the heating element in the rear window and cause damage. Note The ventilation slots in front of the rear side windows must not be covered as this would prevent stale air being extracted from the vehicle.
Page 151 Roof carrier* Please observe the following points if you intend to carry loads on the roof: • For safety reasons, only luggage racks and accessories approved by SEAT should be used. • It is imperative to precisely follow the fitting instructions included for the...
Page 152: Heating, Ventilation And Air Conditioning
Heating, Ventilation and Air conditioning Heating, Ventilation and Air conditioning Heating and ventilation Controls and equipment Fig. 126 On the dash panel: Heater controls ⇒ fig. 126 – Using the controls and the control Maximum heat output, which is needed to defrost the windows quickly, is only available when the engine has reached its operating temperature.
Page 153 Heating, Ventilation and Air conditioning With low temperatures outside, the air recirculation increases the effective- ness of the heating system by heating the air inside the passenger compart- ment rather than the air from outside. Air distribution Control for setting the flow of air in the required direction. ...
Page 154: Climatic
Heating, Ventilation and Air conditioning Climatic* Control switches Fig. 127 On the dash panel: Climatic controls  The climatic or semi-automatic air conditioning system only works Button – Rear window heating. The heating will be switched off auto- matically approximately 20 minutes after switching on. It can also be when the engine is running and the turbine is switched on.
Page 155 Heating, Ventilation and Air conditioning Note Please observe the general notes ⇒ page 159. Heating and cooling the interior Fig. 128 On the dash panel: Climatic controls Heating of the vehicle interior Cooling the passenger compartment ⇒ fig. 128 ⇒ page 152, –...
Page 156 Heating, Ventilation and Air conditioning – Use the air distribution control to guide the flow of air in the comfort for the vehicle occupants and prevents misting of the windows when the ambient air humidity is high. required direction:  (to the windscreen), ...
Page 157: 2C-Climatronic
Heating, Ventilation and Air conditioning ⇒ page 154, fig. 129  Air recirculation mode prevents strong odours in For reasons of safety, air recirculation is not possible when the control for air  the outside air from entering the vehicle interior, for example when passing distribution is set to the windscreen setting through a tunnel or in queuing traffic.
Page 158 Heating, Ventilation and Air conditioning Blower control ⇒ page 157 The air conditioning system only works when the engine is running – Switches the 2C-Climatronic on and off ⇒ page 157 and the blower is switched on. Button Button AUTO –...
Page 159 Heating, Ventilation and Air conditioning – Press the temperature selectors to set the desired temperatures Climatronic maintains a constant temperature level fully automatically. The temperature of the air supplied to the interior, the blower speed and the air for the left and right sides of the interior. We recommend 22°C distribution are regulated automatically.
Page 160 Heating, Ventilation and Air conditioning Air recirculation mode Temperature There are separate temperature selectors for the left and right sides of the Air recirculation mode prevents fumes or unpleasant smells vehicle interior. The selected temperature is displayed above the selector. It from entering the vehicle.
Page 161: General Notes
Heating, Ventilation and Air conditioning • General notes The air conditioning system operates most effectively with the windows and the sliding/tilting roof* closed. However, if the sun has heated up the vehicle, the air inside can be cooled more quickly by opening the windows for The pollen filter a short period.
Page 162: Address
The height and reach of the steering wheel can be freely adjusted to suit the driver. Fig. 133 Proper sitting position for driver – Adjust the driver seat to the correct position. ⇒ fig. 132 – Push the lever under the steering column down ⇒...
Page 163: Safety
Driving Safety WARNING (continued) • Adjust the driver seat or steering wheel so that there is a distance of at ⇒ page 160, Electronic stabilisation programme (ESP)* least 25 cm between the steering wheel and your breast bone fig. 133. If you fail to observe the minimum distance, the airbag will not ESP helps make driving safer in certain situations.
Page 164: Ignition Lock
Driving • Ignition lock when rocking the vehicle backwards and forwards to free it from mud, for example. You should press the button to switch the ESP back on when you no longer Position of the ignition key need wheel spin. The TCS and EDL are also switched off if the ESP is switched off.
Page 165: Starting And Stopping The Engine
Wait for the vehicle to come to a standstill before removing the ignition The engine can only be started using a genuine SEAT key with the correct key from the lock. The steering lock could be activated immediately - Risk code.
Page 166 10 seconds and try again after about half a minute. If the engine still does not The engine can only be started using a genuine SEAT key with start, the fuel pump fuse should be checked ⇒ page 247, “Fuses”.
Page 167 Driving Glow plug system for the diesel engine For the sake of the environment To avoid unnecessary load on the battery, do not use any other major elec- Do not warm-up the engine by running the engine with the vehicle stationary. trical equipment while the glow plugs are pre-heating.
Page 168: Manual Gearbox
Driving Caution If the engine has been driven hard for a long period, the engine could over- heat when it is switched off. Risk of engine damage. For this reason, you should idle the engine for approx. 2 minutes before you switch it off. Manual gearbox Fig.
Page 169: Automatic Gearbox* / Dsg Automatic Gearbox
Driving Automatic gearbox* / DSG automatic WARNING gearbox* • When the engine is running, the vehicle will start to move as soon as a gear is engaged and the clutch released. • Never select the reverse gear when the vehicle is in motion. Risk of acci- Selector lever positions dent.
Page 170 Driving Driving programmes the full power of the engine. This programme is not recommended for use on the motorway or in the city. The automatic gearbox / direct shift gearbox has three Selecting the manual programme (tiptronic) programmes. This programme allows driving similar to a manual gearbox. You can access this program from the gear stick or from the paddles on the steering wheel, if this option exists ⇒...
Page 171 Driving – Press and release the brake pedal, at the same time press the Driving button on the selector lever. – Press and hold the foot brake. – Press on the button on the selector lever knob (on the left The lock is only activated when the vehicle is stopped or at a speed of less ⇒...
Page 172 Driving Hill stop WARNING (continued) – Hold the vehicle, in all cases, using the foot brake to prevent • If you must stop on a hill, always hold the vehicle using the footbrake rolling back. to avoid rolling back. • –...
Page 173 Driving Using the Tiptronic gear system General information about driving in Tiptronic mode The Tiptronic system allows the driver to manually select Changing gear with the gear stick gears – Put the lever in position D and push to the right to enter the ⇒...
Page 174: Handbrake
Driving Applying the handbrake Note ⇒ fig. – Pull the handbrake lever up firmly 144. • The gearbox controls on the steering wheel can operate with the gear stick in any position and with the vehicle in motion. Releasing the handbrake –...
Page 175: Acoustic Parking Aid System
Driving Parking WARNING (continued) • The handbrake should always be firmly applied when the Never park where the hot exhaust system could ignite inflammable vehicle is parked. materials, such as dry grass, low bushes, spilt fuel etc. • Never allow vehicle occupants to remain in the vehicle when it is Always note the following points when parking the vehicle: locked.
Page 176 Driving Activation WARNING (continued) The system is activated by engagement of the reverse gear. A brief acoustic • signal confirms the activation and correct function of the system. Always look out for small children and animals because the system will not always detect them.
Page 177: Cruise Control System (Ccs)
Driving Cruise control system (CCS)* Switching the cruise control system on and off Description The cruise control system is able to maintain the set speed in the range from approx. 30 km/h to 180 km/h. Once the speed setting has been saved, you may take your foot off the accel- erator.
Page 178 Driving Setting speed* Adjusting set speed* The speed can be altered without touching the accelerator or the brake. Fig. 146 Turn signal and main beam headlight lever switch and rocker switch for the cruise Fig. 147 Turn signal and control main beam headlight lever switch and rocker switch for the cruise...
Page 179 Driving • When you increase speed with the accelerator and then release the pedal, the if the clutch pedal is depressed, • system will automatically restore the set speed. This will not be the case, if the vehicle is accelerated to over 180 km/h, however, if the vehicle speed is more than 10 km/h higher than the stored •...
Page 180 Driving Vehicles with a manual gearbox The system is completely turned off by moving the control all the way to the right hand side (OFF engaged), or when the vehicle is stationary, ignition off. Vehicles with automatic gearbox / DSG automatic gearbox* To completely disengage the system, the selector lever must be placed in one of the following positions: P, N, R or 1 or with the vehicle stopped and the ignition turned off.
Page 181: Tips And Maintenance
Intelligent technology Tips and Maintenance Intelligent technology Brakes The brake assist system intervenes here, if you press the brake pedal very quickly, the brake assist system registers an emergency situation. It then very quickly builds up the full brake pressure so that the ABS can be activated Brake servo more quickly and efficiently, thus reducing the braking distance.
Page 182: Anti-Lock Brake System And Traction Control M-Abs (Abs And Tcs)
Intelligent technology Anti-lock brake system and traction control WARNING (continued) M-ABS (ABS and TCS) • The effectiveness of ABS is also determined by the tyres fitted ⇒ page 229. • If the running gear or brakes are modified, the effectiveness of the ABS Anti-lock brake system (ABS) could be severely limited.
Page 183: Electronic Stabilisation Programme (Esp)
Intelligent technology The TCS should be switched on again afterwards as soon as possible. Electronic Stabilising Program (ESP)* ESP reduces the danger of skidding by braking the wheels individually. WARNING The system uses the steering wheel angle and road speed to calculate the •...
Page 184 Intelligent technology a slippery road surface on one side of the vehicle. It does this by braking the Caution wheel which has lost traction and distributing more driving force to the other • driven wheel via the differential. In order to ensure that ESP functions correctly, all four wheels must be fitted with the same tyres.
Page 185 Intelligent technology Brakes If the brakes are not used frequently, or if corrosion has formed on the discs, it is advisable to clean off the pads and discs by braking firmly a few times from a moderately high speed ⇒ What factors can have a negative effect on the brakes? Faults in the brake system New brake pads...
Page 186 Intelligent technology and prolongs the service life of the brakes. If you still have to use the brakes, WARNING (continued) it is better to brake firmly at intervals than to apply the brakes continuously. • New brake pads must be run in and do not have the correct friction during the first 200 km.
Page 187 Intelligent technology • Power steering (servotronic*) The power steering requires a special hydraulic fluid. The container is located in the engine compartment (front left). The correct fluid level in the The power steering assists the driver when turning the reservoir is important for the power steering to function properly. The hydraulic fluid level is checked at the Inspection Service.
Page 188: Driving And The Environment
Driving and the environment Driving and the environment Running-in Running in tyres and brake pads New tyres should be run-in carefully for the first 500 km. New Running in a new engine brake pads should be run-in carefully for the first 200 km. The engine needs to be run-in over the first 1,500 km.
Page 189: Driving Abroad
Driving and the environment Diesel engine particulate filter* – For engine oil changes, do not replenish with too much engine oil ⇒ page 218, “Topping up engine oil ”. The diesel engine particulate filter eliminates soot produced – Never tow the vehicle to start it, use jump leads if necessary by burning diesel.
Page 190 Authorised Service Centres may only carry out limited repairs. SEAT importers and distributors will gladly provide information about the technical preparation of your vehicle in addition to necessary maintenance and repair possibilities.
Page 191 Driving and the environment On the left hand side headlight, if you are changing from driving on the left- On the right headlight, if you are changing from driving on the left-hand side ⇒ page 188, fig. hand side to the right-hand side 151.
Page 192 Driving and the environment Adjustments for Bixenon headlights for driving on the left On the left hand side headlight, if you are changing from driving on the left- ⇒ fig. hand side to the right-hand side 155. Covering Bixenon headlights for driving on the right Fig.
Page 193: Driving Economically And With Respect For The Environment
Driving and the environment On the right headlight, if you are changing from driving on the left-hand side Avoid driving at high speed to the right-hand side. We advise you not to drive at the top speed permitted by the vehicle. Fuel consumption, exhaust emissions and noise levels all increase very rapidly at On the left headlight, if you are changing from driving on the left-hand side to higher speeds.
Page 194 This is the reason why we recommend avoiding Environmental protection is a top priority in the design, choice of materials short trips wherever possible. and production of your new Seat Maintain the correct tyre pressures Design measures for economical recycling •...
Page 195 Driving and the environment • Surplus materials used extensively for energy conversion and building materials • Overall water consumption reduced • Heat recovery systems • Water-soluble paint Safety First Operating instructions Tips and Maintenance Technical Data...
Page 196: Trailer Towing
Set the tyre pressure of the trailer tyres in If the trailer has a 7-pin plug you will need to use an adapter cable. This is accordance with the trailer manufacturer's recommendations. available from any SEAT dealer. Exterior mirrors Trailer weight / draw bar loading Check whether you can see enough of the road behind the trailer with the Never exceed the authorised towing limit.
Page 197: Ball Coupling Of Towing Bracket
Trailer towing • Find out whether special regulations apply to towing a trailer in your Speed country. The stability of the vehicle and trailer is reduced with increasing speed. For this reason it is advisable not to drive at the maximum permissible speed in unfavourable road, weather or wind conditions.
Page 198: Fitting A Towing Bracket
Trailer towing Fitting a towing bracket* It is possible to fit a towing bracket to the rear of the vehicle. Fig. 158 Attachment points for towing bracket...
Page 199 Trailer towing If a towing bracket is to be fitted after the vehicle is purchased, this must be WARNING (continued) completed according to the instructions of the towing bracket manufacturer. • If the towing bracket is incorrectly installed, there is serious danger of The attachment points for the towing bracket are underneath the vehicle.
Page 200: Cleaning And Caring For Your Vehicle
Cleaning and caring for your vehicle Cleaning and caring for your vehicle General notes WARNING (continued) your vehicle. The use of certain products may produce noxious vapours; Regular washing and care help maintain the value of your these should be used in well ventilated areas. vehicle.
Page 201: Care Of The Vehicle Exterior
Cleaning and caring for your vehicle Care of the vehicle exterior Washing by hand Washing the vehicle Automatic car wash tunnel – First soften the dirt with plenty of water and rinse off. The car can normally be washed without problem in an auto- –...
Page 202 Cleaning and caring for your vehicle Washing the car with a high pressure cleaner WARNING (continued) • Be particularly careful when using a high pressure cleaner! Protect your hands and arms from cuts on sharp metal edges when cleaning the underbody, the inside of the wheel housings etc. Risk of –...
Page 203 Cleaning and caring for your vehicle • especially important for bumpers painted in the same colour as the vehicle. Do not use polishes and hard wax on painted parts with a matte finish or The closer the nozzle is to the surface, the greater the wear on the material. on plastic parts.
Page 204 Cleaning and caring for your vehicle Care of rubber seals Use a clean cloth or chamois leather to dry the windows. Chamois leathers which have been used on painted surfaces are not suitable for use on If rubber seals are well looked after, they will not freeze so windows.
Page 205 Cleaning and caring for your vehicle Cleaning alloy wheels If this does not provide satisfying results, use a specialist chrome cleaning product. Chrome cleaning products will remove stains and coatings from the surface. Every two weeks – Wash salt and brake dust from alloy wheels. Caution –...
Page 206 Cleaning and caring for your vehicle Underbody sealant The anti-corrosion protection is usually removed if the engine compartment is cleaned with grease removing solutions, or if you have the engine cleaned. The underside of the vehicle is coated to protect it from corro- If this job is carried out, you should ensure that all surfaces, seams, joints and components in the engine compartment are given anti-corrosion treatment sion and damage.
Page 207: Care Of The Vehicle Interior
Care of the vehicle interior Cleaning cloth seat covers and fabric trim Cloth seat covers and fabric trim on the doors, headlining etc. can be cleaned Cleaning plastic parts and the dash panel with a special interior cleanser or with dry foam and a soft brush.
Page 208 • Do not use chemical cleaning agents on the seat belts, as this can Dust and grit in the pores and seams can scratch and damage the surface. If impair the strength of the webbing. Ensure that the belts do not come into the vehicle is left standing in the sun for long periods, the leather should be contact with corrosive fluids.
Page 209: Accessories, Parts Replacement And Modifications
Due to the way the electronic components Despite continuous observation of the market, SEAT is not able to assess the are linked together in networks, other systems may be affected by the faults. reliability, safety and suitability of parts not approved by SEAT. For this reason...
Page 210: Roof Aerial
Accessories, parts replacement and modifications WARNING WARNING • Incorrectly performed modifications or other work on your vehicle can lead Always concentrate primarily on driving. If you are distracted while to malfunctions and cause accidents. driving you could have an accident. •...
Page 211: Checking And Refilling Levels
Checking and refilling levels Checking and refilling levels Refuelling – Turn the key in the lock, without releasing the cap in the clock- wise direction 180°. The tank flap is released manually. The tank holds approxi- – Remove the key and close the flap until it clicks into place. The mately 55 litres.
Page 212: Petrol
Checking and refilling levels Fuel types are differentiated by the octane rating, e.g: 91, 95, 98 RON (RON WARNING (continued) = “Regulation Octane Number, unit for determining the knock resistance of − Insert the fuel nozzle into the mouth of the canister as far as petrol”).
Page 213: Diesel
Checking and refilling levels • Petrol additives DIN is a German abbreviation for “Deutsches Institut für Normung e.V.”, the German standards institute. • Petrol additives improve the quality of the petrol. EN means European Norm. • FAME is the English abbreviation “Fatty Acid Methyl Ester”. The quality of the petrol influences running behaviour, performance and service life of the engine.
Page 214: Working In The Engine Compartment
All service fluids and consumables, e.g. coolant, engine oil, spark plugs and batteries, are being constantly developed. SEAT provides a constant flow of information to the Authorised Service Centres concerning modifications. For...
Page 215 Checking and refilling levels this reason we recommend that you have service fluids and consumables WARNING (continued) replaced by an Authorised Service Centre. Please observe the relevant instructions ⇒ page 207. The engine compartment of any motor vehicle is a •...
Page 216 Checking and refilling levels Caution When changing or topping up service fluids, make absolutely certain that you fill the fluids into the correct reservoirs. Failure to observe this point will result in serious malfunctions and engine damage! For the sake of the environment Service fluids leaks are harmful to the environment.
Page 217: Engine Oil
Checking and refilling levels Engine oil WARNING (continued) • Wait until no more steam, smoke or coolant is emitted from the bonnet, Engine oil specifications then carefully open the bonnet. • When working in the engine compartment, always observe the safety The engine oil used must conform with exact specifications.
Page 218 Checking and refilling levels Oil properties Viscosity The viscosity class of the oil is selected according to the diagram. When the ambient temperature falls outside the limits of the scale for a short period, an oil change is not required. Fig.
Page 219 Checking and refilling levels – Pull out the dipstick. Wipe the dipstick with a clean cloth and Note insert it again, pushing it in as far as it will go. Before a long trip, we recommend finding an engine oil that conforms to the ⇒...
Page 220 Checking and refilling levels  Engine oil specification ⇒ page 215. Topping up engine oil Top up gradually with small quantities of oil. WARNING Oil is highly inflammable! Ensure that no oil comes into contact with hot engine components when topping up. Caution If the oil level is above the area do not start the engine.
Page 221: Coolant
Checking and refilling levels Coolant WARNING (continued) • Before opening the bonnet, read and observe the warnings ⇒ page 212, “Safety instructions on working in the engine compartment”. Coolant specifications • Wait for the engine to cool down. Hot oil may cause burn injuries. Coolant is a mixture of water and at least 40% coolant addi- •...
Page 222 Checking and refilling levels Opening the coolant expansion tank Caution – Switch off the engine and allow it to cool. • Other additives may give considerably inferior corrosion protection. The resulting corrosion in the cooling system can lead to a loss of coolant, –...
Page 223: Washer Fluid And Windscreen Wiper Blades
Checking and refilling levels Washer fluid and windscreen wiper blades The coolant additive G 12+ (dyed purple) may be mixed with G 12 (dyed red) and also with G 11.  Topping up washer fluid WARNING The water for cleaning the windscreen should always be Any work carried out in the engine compartment or on the engine must be mixed with washer fluid.
Page 224 Checking and refilling levels Changing windscreen wiper blades WARNING If the windscreen wiper blades are in perfect condition, you Any work carried out in the engine compartment or on the engine must be will benefit from an improved visibility. Damaged wiper carried out cautiously.
Page 225 Checking and refilling levels To change the blades it is necessary to change the rest position of WARNING the wipers to the service position. Do not drive unless you have good visibility through all windows! Service position (for changing wiper blades) •...
Page 226 Checking and refilling levels Changing the rear wiper blade If this is not sufficient, refer to a qualified workshop. A good rear wiper blade is essential for clear rear vision. WARNING Damaged wiper blades should be replaced immediately. Do not drive unless you have good visibility through all windows! •...
Page 227: Brake Fluid
⇒ page 276. The brake fluid reservoir has a black and It is important that you use only brake fluid compliant with the US standard FMVSS 116 DOT 4. We recommend the use of Genuine SEAT brake fluid. yellow cap.
Page 228: Battery
Checking and refilling levels Battery WARNING (continued) • Before opening the bonnet to check the brake fluid level, read and observe the warnings ⇒ page 212. Warnings on handling the battery • Brake fluid should be stored in the closed original container in a safe place out of reach of children.
Page 229 Checking and refilling levels • If the vehicle is left standing in cold conditions for a long period, protect WARNING (continued) the battery from frost. If it “freezes” it will be damaged. charge. Never short the battery terminals. High-energy sparks can cause injury.
Page 230 Replacing a vehicle battery The battery has been developed to suit the conditions of its location and has special safety features. Genuine SEAT batteries fulfil the maintenance, performance and safety spec- ifications of your vehicle. WARNING •...
Page 231: Wheels And Tyres
Wheels and tyres Wheels and tyres Wheels Concealed damage Damage to tyres and rims is often not readily visible. If you notice unusual vibrations or the car pulling to one side, this may indicate that one of the tyres General notes is damaged.
Page 232 Wheels and tyres Tyre pressure monitoring 2. The tyre pressures should only be checked when the tyres are cold. The slightly raised pressures of warm tyres must not be The tyre pressure monitoring system constantly checks the reduced. pressure of the tyres. 3.
Page 233 Wheels and tyres Significant tyre pressure loss  The tyre symbol is displayed and indicates that the tyre pressure for a least one tyre is insufficient. - Stop the vehicle. - Switch the engine off. - Check the tyre(s). - Change the wheel if necessary. Fig.
Page 234 Wheels and tyres Changing wheels around For the sake of the environment If the front tyres are worn considerably more than the rear ones it is advisable ⇒ page 231, fig. Under-inflated tyres will increase fuel consumption. to change them around as shown 172.
Page 235 SEAT are specially matched to the characteristics off and cause damage to the fuel lines, brake pipes or fuel filler.
Page 236 This can also apply to wheels of the same model. The use of “DOT ... 1103 ...” means, for example, that the tyre was produced in the 11th wheels or tyres which have not been approved by SEAT for use with your week of 2003.
Page 237 Wheels and tyres heads must be used. This ensures that wheels are fitted securely and that the Winter tyres must be inflated to a pressure 0.2 bar higher than the pressures brake system functions correctly. specified for summer tyres (see sticker on tank flap). In certain circumstances, you may not use wheel bolts from a different car - Winter tyres must be fitted on all four wheels.
Page 238 Wheels and tyres For the sake of the environment Fit your summer tyres in good time. They are quieter, do not wear so quickly and reduce fuel consumption. Snow chains Snow chains may be fitted only to the front wheels, and only to certain tyre sizes ⇒...
Page 239: If And When
If and when If and when Tools, tyre repair kit and spare wheel WARNING (continued) • The jack* supplied by the factory is only designed for changing wheels Vehicle Tools on this model. On no account attempt to use it for lifting heavier vehicles or other loads, risk of injury.
Page 240 If and when Compact temporary spare wheel* Snow chains For technical reasons, snow chains must not be used on the compact tempo- The compact spare wheel (emergency wheel for vehicles rary spare wheel. without the anti-puncture kit) should only be used when If you should have a puncture on one of the front wheels when using snow strictly necessary.
Page 241: Wheel Change
If and when Note WARNING • Seek professional assistance if the repair of a tyre puncture is not Put the hazard warning lights on and place the warning triangle in position. possible with the sealing compound. This is for your own safety and also warns other road users. Caution Wheel change If you have to change the tyre on a gradient, block the wheel opposite the...
Page 242 If and when After changing a wheel Wheel trims After changing the wheel there are still tasks to complete. The wheel trims must be removed to gain access to the wheel bolts. – Put the tools and jack back in the luggage compartment. –...
Page 243 If and when Wheel covers* Loosening the wheel bolts The wheel covers must be removed for access to the wheel The wheel bolts must be loosened before raising the vehicle. bolts Removing – Remove the wheel cover using the wire hook. –...
Page 244 If and when WARNING Loosen the wheel bolts only about one turn before raising the vehicle with the jack, loosening the wheel bolts more than one turn can result in an acci- dent. Note • Do not use the hexagonal socket in the screwdriver handle to loosen or tighten the wheel bolts.
Page 245 If and when Raising the vehicle – Locate the jacking point under the door sill closest to the wheel ⇒ fig. being changed 176. The vehicle must be raised with a jack to remove the wheel. – Wind up the jack under the jacking point until the arm of the jack is directly below the vertical rib under the door sill.
Page 246 If and when Removing and fitting the wheel The wheel bolts should be clean and turn easily. Before fitting the spare wheel, inspect the condition of the wheel and hub mounting surfaces. These For removal and fitting the wheel, the following tasks must be surfaces must be clean before fitting the wheel.
Page 247: Tyre Repair Kit* (Tyre Mobility System)
If and when Tyre repair kit* (Tyre Mobility System)* – Insert the adapter onto the wheel bolt and push it on as far as it ⇒ page 244, fig. will go 179. – Fit the box spanner as far as it will go over the adapter. General information and safety notes –...
Page 248 If and when Note Note Seek professional assistance if the repair of a tyre puncture is not possible Please observe legal requirements when doing so. with the sealing compound. Tyre repair Preparation work The following sections describe the procedures for repairing Certain steps must be taken before repairing a tyre.
Page 249: Fuses
If and when Note The compressor should never be allowed to run for longer than 6 minutes. Fuses Changing a fuse If a fuse has blown it must be replaced Fig. 181 Fuse box cover in engine compartment Fuse cover underneath the steering wheel –...
Page 250 If you replace a fuse with a stronger fuse, you could cause damage to another location in the electrical system. Colour Amperes • Always keep some spare fuses in the vehicle. These are available from light brown SEAT dealers. Blue yellow natural (white) green orange white...
Page 251 If and when Fuses on left side of dash panel Fuses Number Consumer Amperes Vacant Vacant Vacant Vacant Vacant Vacant Vacant Vacant Airbag RSE input (roof screen) Vacant Vacant Left xenon headlight Heating controls / ESP, ASR switch / Reverse / Preinstallation of telephone / Tomtom Navigator ABS/ESP switchboard / Engine / Headlights / Trailer switchboard / Light switch / Instrument panel Headlight regulation switchboard / Heated wipers / Instrument lights / Diagnosis Switchboard Right xenon headlight...
Page 252 If and when Number Consumer Amperes Cable control unit Volumetric alarm sensor/ Alarm horn Diagnosis / Rain sensor / Light switch Vacant Switchboard coupling automatic gearbox Vacuum pump RSE input (roof screen) Rear wiper motor / Switchboard wiring Vacant Cigarette lighter / socket Vacant Vacant Heater...
Page 253 If and when Number Consumer Amperes Electric windows (front) Rear electric windows Engine (Fuel control unit, petrol relay) Convenience controls Heating controls Heated seats Sunroof Headlight washer system Vacant Taxi (taximeter power supply) Vacant Taxi (taximeter power supply) Vacant Central locking control unit Some of the electrical items listed in the table are only fitted on certain models or are optional extras.
Page 254 If and when Fuses layout, engine compartment, left part Fuses Number Consumer Amperes Windscreen wipers Steering column Cable control unit AQ gearbox instrument panel Vacant Radio Telephone/TomTom Navigator Engine management Engine management Vacant Electronic control unit Petrol injection module supply Diesel injection module supply Coil Engine management...
Page 255 If and when Number Consumer Amperes Clean Vacant Lambda probe Brake pedal, speed sensor Engine management Engine management Engine management AKF, gearbox valve Right lighting Left lighting Engine management Engine management Ignition key Electric windows (front and back) Electric windows (front) Ignition key Safety First Operating instructions...
Page 256: Bulb Change
If and when Position in engine compartment: Side box Fuses Number Consumer Amperes Alternator < 140 W Alternator > 140 W Power steering servo Multi-terminal voltage supply “30”. Internal fuse box Ventilator > 500 W / Ventilator < 500 W 80/50 PTCs (Supplementary electrical heating using air) PTC (Supplementary electrical heating using air)
Page 257 Turn signals Dipped headlights Main beam headlights On this type of headlight, the bulb changes must be made by the SEAT dealer, given Side lights that complex elements must be removed from the vehicle and a reset must be made on the automatic control system incorporated.
Page 258 If and when Turn signal lamps Dipped beam lights Fig. 183 Turn signal Fig. 184 Dipped head- lamps lights – Raise the bonnet. ⇒ fig. 183 – Rotate the lamp holder to the left and pull. – Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
Page 259 If and when ⇒ page 256, fig. 184 – Remove the loops in the direction of the arrow and remove the cover. ⇒ page 256, fig. 185 – Remove the connector from the bulb. ⇒ page 256, fig. 185 – Disengage the retainer spring pressing inwards and to the right.
Page 260 If and when ⇒ fig. 189 Side lights – Extract the lamp holder outwards. – Replace the bulb by pulling this out and inserting the replace- ment. – Installation is done in the reverse order. Rear lights • Side lights •...
Page 261 If and when Side lights and brake lights – Remove the cover of the luggage compartment lateral panel. ⇒ fig. 191 – Unscrew the plastic fitting securing the rear light. Inserting a screwdriver under the plastic fitting may help to loosen it.
Page 262 If and when ⇒ fig. 192 Turn indicators – Unscrew the bolts from the lamp holder and pull on this. – Pull out the lamp holder from the turn signal using a screw driver ⇒ fig. in the direction of the arrow (see 193).
Page 263 If and when Reverse light / rear fog light – Remove the rear light from its casing taking care not to pull on the cable. – Rotate the lamp holder to the left, and remove it in the direction ⇒ fig. of the arrow 195.
Page 264 If and when – Insert the lamp holder in the indicator guide until it clicks into place. – First place the indicator in the opening in the bodywork, fixing ⇒ page 261, fig. the tabs 196, arrow ⇒ page 261, –...
Page 265 If and when Registration light – Remove the lamp, moving it in the direction of the arrow and ⇒ fig. outwards 200. Fig. 199 Registration plate light Fig. 200 Registration plate light – Remove the tulip-shaped fitting, carefully using the flat side of the screwdriver as a lever inserted in the crack as shown by the ⇒...
Page 266: Jump-Starting
If and when Sunroof light – Remove the lamp, moving it in the direction of the arrow and ⇒ fig. outwards 202. Jump-starting Jump leads The jump lead must have a sufficient wire cross section. If the engine fails to start because of a discharged battery, the battery can be connected to the battery of another vehicle to start the engine.
Page 267 If and when How to jump start: description 4. Connect the other end of the black jump lead to a solid metal component which is bolted on to the engine block, or onto the engine block itself of the vehicle with the flat battery. Do not connect it to a point near the battery ⇒...
Page 268 If and when WARNING • Please note the safety warnings referring to working in the engine compartment ⇒ page 212, “Working in the engine compartment”. • The battery providing assistance must have the same voltage as the flat battery (12V) and approximately the same capacity (see imprint on battery).
Page 269: Towing And Tow-Starting
If and when Towing and tow-starting Comments Please observe the following points if you use a tow-rope: Tow-starting Notes for the driver of the towing vehicle The use of jump leads is preferable to tow-starting. – Drive slowly at first until the tow-rope is taut. Then accelerate We recommend that you do not tow-start your vehicle.
Page 270 If and when • Do not pull too hard with the towing vehicle and take care to avoid jerking the The towing eye should always be kept in the vehicle. Please refer to the notes on ⇒ page 267, “Tow-starting”. tow-rope.
Page 271 If and when Fitting the towing eye – Take the towing ring from the onboard tools. – Pull the lower front cover down and leave the cover hanging on the vehicle. – Remove the cover of the screw hole, insert a screwdriver into the lower slot and lever gently.
Page 273: Technical Data
General notes on the technical data Technical Data General notes on the technical data What you should be aware of General notes All data in the official vehicle documents take precedence over this data. All data in these documents are valid for the basic model as offered in Spain. The figures may be different if additional equipment is fitted, for different The vehicle data card included in the Maintenance Programme or the vehicle models, for special vehicles and for other countries.
Page 274 General notes on the technical data Vehicle identification data Vehicle data The data sticker is placed on the inside of the spare wheel recess in the The most important data are given on the type plate and the luggage compartment. vehicle data sticker.
Page 275: How Are The Figures Measured
General notes on the technical data How are the figures measured? Fuel consumption The consumption and emission details shown on the vehicle data sticker differ from one vehicle to another. The fuel consumption and CO emissions of the vehicle can be found on the The consumption and emission figures are calculated in accordance with the vehicle data sticker.
Page 276: Towing A Trailer
General notes on the technical data Weights Drawbar load The maximum permitted weight exerted by the trailer drawbar on the ball joint of the towing bracket must not exceed 75 kg. Kerb weight refers to the basic model with a fuel tank filled to 90% capacity and without optional extras.
Page 277 General notes on the technical data Snow chains Snow chains may be fitted only to the front wheels. Consult the chapter “wheels” of this manual. Wheel bolts After the wheels have been changed, the tightening torque of the wheel bolts should be checked as soon as possible with a torque wrench ⇒...
Page 278: Technical Data
Technical data Technical data Checking fluid levels Overview Further explanations, instructions and restrictions on the technical data are contained as of ⇒ page 271. From time to time, the levels of the different fluids in the vehicle must be checked. Never fill with incorrect fluids, to do so may cause serious damage to the engine.
Page 279: Petrol Engine 1.4 63 Kw (86 Bhp)
Technical data Petrol engine 1.4 63 kW (86 bhp) General engine data Power output in kW (bhp) 63 (86)/ 5000 Maximum torque in Nm at rpm 132/ 3800 No. of cylinders, capacity 4/ 1390 in cm 10,5 ± 0,3 Compression ratio Fuel Premium unleaded 95 RON or regular unleaded 91 RON With a slight power loss...
Page 280: Petrol Engine 1.4 92 Kw (125 Bhp)
Technical data Engine oil capacity Approximate engine oil capacity with oil filter change 2.8 litres Petrol engine 1.4 92 kW (125 bhp) General engine data Power output in kW (bhp) 92 (125)/ 5600 Maximum torque in Nm at rpm 200/ 1750-4000 No.
Page 281: Petrol Engine 1.6L 75 Kw (102 Bhp)
Technical data Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1200 Engine oil capacity Approximate engine oil capacity with oil filter change 3.3 litres Petrol engine 1.6l 75 kW (102 bhp) General engine data Power output in kW (bhp) 75 (102)/ 5600 Maximum torque...
Page 282: Petrol Engine 1.8 118 Kw (160 Bhp)
Technical data Weights Gross vehicle weight in kg 1944 Weight in working order (with driver) in kg 1419 Gross axle weight, front in kg Gross axle weight, rear in kg 1010 Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1200 Engine oil capacity...
Page 283 Technical data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. Weights Gross vehicle weight in kg 2059 Weight in working order (with driver) in kg 1534 Gross axle weight, front in kg 1061 Gross axle weight, rear...
Page 284: Petrol Engine 2.0 110 Kw (150 Bhp)
Technical data Petrol engine 2.0 110 kW (150 bhp) General engine data Power output in kW (bhp) 110 (150)/ 6000 Maximum torque in Nm at rpm 200/ 3500 No. of cylinders, capacity 4/ 1984 in cm 11,5 ± 0,5 Compression ratio Fuel Super Plus unleaded 98 RON or Premium unleaded 95 RON With a slight power loss...
Page 285: Petrol Engine 2.0 Litre 110 Kw (150 Bhp). Automatic
Technical data Engine oil capacity Approximate engine oil capacity with oil filter change 4.6 litres Petrol engine 2.0 litre 110 kW (150 bhp). Automatic General engine data Power output in kW (bhp) 110 (150)/ 6000 Maximum torque in Nm at rpm 200/ 3500 No.
Page 286: Petrol Engine 2.0 Litre 147 Kw (200 Bhp). Manual
Technical data Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1400 Engine oil capacity Approximate engine oil capacity with oil filter change 4.6 litres Petrol engine 2.0 litre 147 kW (200 bhp). Manual General engine data Power output in kW (bhp) 147 (200)/5100- 6000...
Page 287: Petrol Engine 2.0 Litre 147 Kw (200 Bhp). Automatic
Technical data Weights Gross vehicle weight in kg 1960 Weight in working order (with driver) in kg 1492 Gross axle weight, front in kg 1079 Gross axle weight, rear in kg 1001 Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1400 Engine oil capacity...
Page 288 Technical data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. Weights Gross vehicle weight in kg 2092 Weight in working order (with driver) in kg 1564 Gross axle weight, front in kg 1109 Gross axle weight, rear...
Page 289: Diesel Engine 1.9L Tdi 77 Kw (105 Bhp)
Technical data Diesel engine 1.9l TDI 77 kW (105 bhp) General engine data Power output in kW (bhp) 77 (105) 4000 Maximum torque in Nm at rpm 250/1900 No. of cylinders, capacity 4/1896 in cm 19 ± 0,5 Compression ratio Fuel Min.
Page 290: Diesel Engine 1.9 Tdi 77 Kw (105 Bhp). Automatic
Technical data Engine oil capacity Approximate engine oil capacity with oil filter change Diesel engine 1.9 TDI 77 kW (105 bhp). Automatic General engine data Power output in kW (bhp) 77 (105) 4000 Maximum torque in Nm at rpm 250/1900 No.
Page 291: Diesel Engine 2.0L 103 Kw (140 Bhp). Manual
Technical data Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1400 Engine oil capacity Approximate engine oil capacity with oil filter change Diesel engine 2.0l 103 kW (140 bhp). Manual General engine data Power output in kW (bhp) 103 (140)/ 4000 Maximum torque...
Page 292: Diesel Engine 2.0L 103 Kw (140 Bhp). Automatic
Technical data Weights Gross vehicle weight in kg 2054 Weight in working order (with driver) in kg 1529 Gross axle weight, front in kg 1075 Gross axle weight, rear in kg 1010 Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1400 Engine oil capacity...
Page 293 Technical data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. Weights Gross vehicle weight in kg 2089 Weight in working order (with driver) in kg 1564 Gross axle weight, front in kg 1106 Gross axle weight, rear...
Page 294: Diesel Engine 2.0L 100 Kw (136 Bhp). Manual
Technical data Diesel engine 2.0l 100 kW (136 bhp). Manual General engine data Power output in kW (bhp) 100 (136)/ 4000 Maximum torque in Nm at rpm 320/ 1750 - 2500 No. of cylinders, capacity 4/ 1968 in cm 18,5 ± 0,5 Compression ratio Fuel Min.
Page 295: Diesel Engine 2.0L 100 Kw (136 Bhp). Automatic
Technical data Engine oil capacity Approximate engine oil capacity with oil filter change 4.3 litres Diesel engine 2.0l 100 kW (136 bhp). Automatic General engine data Power output in kW (bhp) 100 (136)/ 4000 Maximum torque in Nm at rpm 320/ 1750 - 2500 No.
Page 296: Diesel Engine 2.0L 125 Kw (170 Bhp)
Technical data Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1400 Engine oil capacity Approximate engine oil capacity with oil filter change 4.3 litres Diesel engine 2.0l 125 kW (170 bhp) General engine data Power output in kW (bhp) 125 (170)/ 4200 Maximum torque...
Page 297 Technical data Weights Gross vehicle weight in kg 2054 Weight in working order (with driver) in kg 1529 Gross axle weight, front in kg 1075 Gross axle weight, rear in kg 1020 Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1400 Engine oil capacity...
Page 298: Dimensions And Capacities
Technical data Dimensions and capacities Dimensions Length, width 4,458 mm / 1,768 mm Height at kerb weight 1,568 mm Front and rear projection 914 mm / 966 mm Wheelbase 2,578 mm Turning circle 10.7 m Front Rear 1,526 mm 1,515 mm Track width 1,534 mm 1,523 mm...
Page 299: Index
Charging ......228 Adjusting the seat belt height ....27 Anti-freeze .
Page 300 Clothes hook ......138 Child seat ....... 48 Central locking button Cockpit .
Page 301 With a trailer ......195 seat ....... 31 emergency manual locking .
Page 302 Specifications ..... . . 215 Folding the seat backrests down ... 133 G 12 .
Page 303 Index head restraints Instrument panel menu Luggage compartment retaining net ..138 Adjusting ..... . 129, 130 Configuration menu .
Page 304 Parts ........207 Rear seat bench ......132 Parts replacement .
Page 305 Indicator ......79 Seat belts ....... 19 Sliding/tilting roof .
Page 306 Ventilation slits ......18 Why wear seat belts? ....19, 21 Tyre Mobility-System (Tyre repair kit) .
Page 307 Index Windscreen wiper blades Cleaning ......202 Windscreen wipers ..... . 121 Changing blades .
Page 308 SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to understand, that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason no right at all may derive based on the data, drawings and descriptions in this current handbook.
Page 309 auto emoción...

Seat 2005 Toledo Owner's Manual

The Structure of this Manual

4 Content

Safety First

Safe Driving

Seat Belts

Airbag System

Child Safety

Operating Instructions

Heating, Ventilation and Air Conditioning

2 C-Climatronic

Tips and Maintenance

Intelligent Technology

Driving and the Environment

Technical Data

General Notes on the Technical Data

Technical Data

Index

Quick Links

Related Manuals for Seat 2005 Toledo

Summary of Contents for Seat 2005 Toledo

Table of Contents