Close Fuel Tap (Only Km 120/150 R G And R D); Close Gas Supply (Only Km 120/150 R Lpg); Transport; Storing The Device - Kärcher KM 120/150 R D Manual

 Only KM 120/150 R G and R LPG: Un-
screw spark plugs and pour approx.
3 cm³ of oil into the spark plug hole.
Crank the engine several times before
replacing the spark plug. Screw in the
spark plug.
 Secure sweeper to prevent it rolling
away, lock parking brake.
 Clean the inside and outside of the
sweeper.
 Park the machine in a safe and dry
place.
 Disconnect battery.
 Charge battery approx. every 2 months.
Close fuel tap (only KM 120/150 R G
and R D)
 Open cover and secure it (Diag. 3).
KM 120/150 R G:
 Push lever in "OFF" direction.
KM 120/150 R D:
 Turn lever to position "S".
 Close cover.
Close gas supply (only KM 120/150
R LPG)
 Close gas drawing valve by turning it in
clock-wise direction.
30

Transport

CAUTION
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
Warning
In general, when shipping the machine, the
freewheel lever must be engaged in the up-
per hole. Only once this has been done, will
the travel drive be ready for operation. The
machine must always be moved up or
down slopes by engaging self-propulsion.
 Turn ignition key to "0" and remove it.
 Only KM 120/150 R G and R D: Empty
tank. Draw off fuel using suitable pump.
 Only KM 120/150 R LPG: Close the gas
cylinder valve and remove the cylinder.
Store the gas cylinder according to the
safety regulations for LPG vehicles.
 Secure the wheels of the machine with
wheel chocks.
 Secure the machine with tensioning
straps or cables.
 Lock parking brake.
Note
Observe markings for fixing points on base
frame (chain symbols). When loading or
unloading the machine, it may only be op-
erated on gradients of max. 18%.

Storing the device

CAUTION
Risk of injury and damage! Note the weight
of the appliance in case of storage.
Park the machine in a safe and dry place.

Maintenance and care

General notes

 First switch off the appliance and re-
move the ignition key before performing
any cleaning or maintenance tasks on
the appliance, replacing parts or switch-
ing over to another function.
 Pull out the battery plug or clamp the
battery while working on the electrical
unit.
Maintenance work may only be carried
–
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety
regulations.
Mobile appliances used for commercial
–
purposes are subject to safety inspec-
tions according to VDE 0701.
10
-
EN
Use only roller brushes/ side-brushes
–
that are provided with the appliance or
specified in the Operations Manual.
The use of other roller brushes/ side-
brushes can affect the safety of the ap-
pliance.
Do not clean the appliance with a water
–
hose or high-pressure water jet (danger
of short circuits or other damage).

Cleaning the inside of the machine

Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
 Open cover and secure it (Diag. 3).
 Clean machine with a cloth.
 Blow through machine with com-
pressed air.
 Close cover.

External cleaning of the appliance

 Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Note
Do not use aggressive cleaning agents.

Maintenance intervals

Note
The elapsed-time counter shows the timing
of the maintenance intervals.
Maintenance by the customer
Daily maintenance:
 Check engine oil level.
 Check axle drive oil level.
 Check tyre pressure.
 Only KM 120/150 R LPG: Check gas
pipes and connecting screws.
 Only KM 120/150 R LPG: Check gas fil-
ter in the screw to the gas cylinder to
see if it is dirty, clean it if required (every
time you change the cylinder).
 Check function of all operator control el-
ements.
Weekly maintenance:
 Check leakiness of fuel or gas connec-
tions.
 Check return-line filter for sweeping
system.
 Check air filter.
 Check oil level of sweeper hydraulics.
 Check hydraulic lines for leaks.
 Check moving parts for freedom of
movement.
 Check the sealing strips in the sweep-
ing area for position and wear.
Maintenance to be carried out every 100
operating hours:
 Check leakiness of fuel or gas connec-
tions.
 Change engine oil (initial change after
20 operating hours).
 Only KM 120/150 R G and R LPG:
Check spark plug.
 Check function of seat contact mat.
 Check battery acid level.