Buell 2002 P3 Service Manual page 77

HOME
TORQUE VALUES
ITEM
Brake bleeder valve
Clutch lever screw
Footpeg support mounting bracket bolts
Frame-to-isolator rear fastener
Front and rear brake rotor screws,
TORX
Front axle nut
Front axle pinch screw
Front brake caliper mounting bolts
Front brake caliper pad hanger pin
Front brake hand lever nut
Front brake hand lever pivot bolt
Front brake line clamp screw
Front brake switch screw
Front fender mounting screws
Front isolator mount bolt
Front muffler bolts
Front sprocket cover bolts
Front tie bar bolt
Handlebar clamp fasteners
Handlebar left and right housing screws
Instrument panel screws
Lower and upper header nuts
Lower belt guard
Master cylinder cover screws
Outboard isolator bolts
Rear axle nut
Rear brake caliper mounting screw,
large
Rear brake caliper mounting screw,
small
2-2 2002 Buell P3: Chassis
TORQUE
3-5 ft-lbs 4-7 Nm
50-60 in-lbs 6-7 Nm
25-30 ft-lbs 34-41 Nm
30-33 ft-lbs 41-45 Nm
24-27 ft-lbs 33-37 Nm
38-42 ft-lbs 52-57 Nm
13-16 ft-lbs 18-22 Nm
18-22 ft-bs 24-30 Nm
11-15 ft-lbs 15-20 Nm
44-62 in-lbs 5-7 Nm
4-13 in-lbs 0.5-1.5 Nm
3-5 ft-lbs 4-7 Nm
7-13 in-lbs 0.8-1.5 Nm
27-30 in-lbs 3.1-3.4 Nm
See NOTES See NOTES
22-25 ft lbs 30-34 Nm
30-36 in-lbs 3-4 Nm
30-33 ft-lbs 41-45 Nm
10-12 ft-lbs 14-16 Nm
25-33 in-lbs 3-4 Nm
30-36 in-lbs 3-4 Nm
6-8 ft-lbs 8-11 Nm
30-36 in-lbs 3-4 Nm
9-13 in-lbs 1.0-1.5 Nm
30-33 ft-lbs 41-45 Nm
48-52 ft-lbs 65-71 Nm
18-22 ft-lbs 24-30 Nm
15-18 ft-lbs 20-24 Nm
NOTES
Metric, Page 2-19
Page 2-63
Page 2-53
Apply several drops of LOCTITE®
thread locker 272 (red) to last few
threads, Page 2-65
Tighten in criss-cross pattern. Apply sev-
eral drops of LOCTITE® thread locker
272 (red) to last few threads, Page 2-11
Apply several drops of LOCTITE®
thread locker 243 (blue) to last few
threads. Metric, Page 2-9
Metric, Page 2-9
Apply several drops of LOCTITE®
thread locker 272 (red) to last few
threads, Page 2-25
Metric, Page 2-25
Metric, Page 2-21
LOCTITE ANTI-SEIZE, Page 2-21
Page 2-26
Page 2-21
Page 2-55
Torque to 20 ft-lbs (27.1 Nm), turn bolt
clockwise an additional 63°-67°, Page 2-
64
Page 2-52
Page 2-54
Page 2-64
Page 2-63
Page 2-63
Apply several drops of LOCTITE®
thread locker 243 (blue) to last few
threads, metric, Page 2-60
Lower first, Page 2-52
Page 2-56
Page 2-25
Page 2-64
Page 2-50
Metric, Page 2-31
Metric, Page 2-31