Introduction; Package Contents; Features - Atlona AT-HDVS-200-TX User Manual

Introduction

The AT-HDVS-200-TX is a 3×1 switcher for HDMI and VGA Inputs with HDBaseT Output. It features
two HDMI inputs, a VGA input, and an always on 3.5mm audio connector. The AT-HDVS-200-
TX can be the central component of a small, automated A/V system. Automatic display control
turns on the display automatically whenever a source is connected. When the source is removed,
the display is turned off. Volume is controlled by using the front panel buttons. Automatic input
selection on the AT-HDVS-200-TX works by sensing the presence of any video signal. With
automatic input selection, manual control systems can be eliminated.
The AT-HDVS-200-TX combines the benefits of a switcher and the advantages of Ethernet-enabled
HDBaseT signal transmission over a single cable. The switcher enables input selection from the front
panel, RS-232, or TCP/IP commands. HDMI signals up to 4K/UHD @ 60Hz with embedded audio,
VGA input signals up to 1920×1200, and control signals can be extended up to 328 feet (100
meters).
Note: To ensure compatibility, please be certain both transmitter and receiver have blue HDBaseT ports. This
ensures both products are PoE (48V) compliant. The HDVS-200-TX is not compatible with PoCC
(black RJ45, 24V) devices

Package Contents

• 1 x AT-HDVS-200-TX
• 1 x Captive screw connector
• 1 x Pair of mounting brackets
• 1 x User Manual

Features

• 2 HDMI
(accepts DVI and DisplayPort with adaptors)
• Auto display control when using TCP/IP, RS-232, or CEC*
• Auto switching with video detection technology
• Device priority - Option to return to a specific port when receiving no signal from the current source
• Control audio volume for HDBaseT output or display
• Adjust volume through front panel, RS-232, or TCP/IP control
Note: Together, CEC and HDBaseT output audio control provide a simple solution for complete audio and
video control, without the need for IP, RS-232, or spending extra programming time.
• Analog audio embedding
• Stand alone audio option - pass analog audio input with no video
• Supports up to 4K @ 60Hz 4:2:0
• Ethernet pass through for configuration, upgrading, and device management/control
• Supports Dolby TrueHD and DTS-HD Master Audio when using HDMI for audio input and output
• HDCP management
• EDID management for better compatibility
• Firmware upgrade via USB or webGUI for easy field service
with AT-HDVS-200-RX
• Scales incoming signals at a variety of common resolutions up to 1080p or 1920x1200
• Dry contact closure control capabilities for up to two devices
• Complete control of video brightness, contrast, saturation, hue, and more
• Projector control through RS-232, IP, or webGUI
• Dual RS-232 port for control systems in addition to projector control
*Note: Consumer Electronics Control (CEC): Atlona does not guarantee the function of CEC with all televisions. We can confirm proper operation with many current
Samsung, Panasonic, and Sony TVs. Many manufacturers do not support the CEC "Off" command when sent from a source and older TVs use proprietary
commands. Atlona only supports those TVs that follow CEC command structure from HDMI 1.2a and support the "off" command when issued by a source. We
encourage any dealer to get evaluation product from Atlona prior to designing a system around this control technology or be prepared to use other methods to
control their displays if Atlona CEC is not compatible with the installed displays.
atlona.com
(3 pin: RS-232)
and 1 VGA/analog audio inputs
(activated through RS-232, IP, or webGUI)
(when used with 4K compatible receivers/switchers e.g. UHD-CLSO series)
3
Toll free: 1-877-536-3976
Local: 1-408-962-0515