Atlona AT-HDVS-200-TX User Manual page 18

SetCmd X[Y]
e.g. SetCmd on[PWR ON]
SetStrgType X
SetEnd X[Y]
e.g. SetEnd off[CR-LF]
SetFbVerify X
e.g. SetFbVerify on
TrigCEC X
e.g. TrigCEC on
TrigRS X
e.g. TrigRS vol+
TrigIP X
e.g. TrigIP vol-
CtlType X
e.g. CtlType rs-232
CliMode X
e.g. CliMode non-login
CliUser X
e.g. CliUser
CliPass X
e.g. CliPass AtlonA
CliIPAddr X
e.g. CliIPAddr sta
CliPort X
e.g. CliPort 24
AutoDispOff X
AutoDispOn X
APwrOffTime X
ProjSWMode X
ProjWarmUpT X
VolKeyOPT X
DispKeyOPT X
DispKeyLock X
DispRS X
DispCEC X
DispIP X
Display X
e.g. Display on
Each command is terminated with a carriage return.
Feedback is terminated with a carriage return and line feed.
Note: If the command fails or is incorrect the feedback should be "Command FAILED"
Volume Key
0 HDVS
Display Key
0 HDVS
atlona.com
SetCmd X[Y]
e.g. SetCmd on[PWR ON]
SetStrgType X
SetEnd X[Y]
e.g. SetEnd off[CR-LF]
SetFbVerify X
e.g. SetFbVerify on
TrigCEC X
e.g. TrigCEC on
TrigRS X
e.g. TrigRS vol+
TrigIP X
e.g. TrigIP vol-
CtlType X
e.g. CtlType rs-232
CliMode X
e.g. CliMode non-login
CliUser X
e.g. CliUser admin
CliPass X
e.g. CliPass AtlonA
CliIPAddr X
e.g. CliIPAddr 192.168.0.23
CliPort X
e.g. CliPort 24
AutoDispOff X
AutoDispOn X
APwrOffTime X
ProjSWMode X
ProjWarmUpT X
VolKeyOPT X
DispKeyOPT X
DispKeyLock X
DispRS X
DispCEC X
DispIP X
Display X
e.g. Display on
1 RS-232 2 IP
1 RS-232 2 CEC
Sets the RS-232 or IP command for the selected button or
function X= on, off, vol+, vol-, and mute Y= command
e.g. Set the on command to send the command PWR ON
Sets the command string type X= ascii, hex, sta
Sets the line termination for the chosen command
X= on, off, vol+, vol-, mute, fbkon, fbkoff, fbkmute
Y= None, CR, LF, CR-LF, Space, STX, ETX, and null
e.g. Set the command off to have a carriage return and line feed
Verifies the device is receiving commands X= on, off, sta
e.g. Sends command up to 4 times until feedback verifies
command was received with feedback
Triggers the stored CEC command to turn the display on
and off X= on, off
Triggers the RS-232 command from RS-232 or IP
X= on, off, vol+, vol-, and mute
Triggers the IP command from RS-232 or IP
X= on, off, vol+, vol-, and mute
Sets the control type X= ip, rs-232, cec
e.g. Set the control type to RS-232
Sets the control device's IP mode X= sta, login, non-login
e.g. Sets the IP mode to non-login
Sets the IP username for login X= username, (blank)
e.g. Display the IP username by leaving x blank
Sets the IP password for login X= password, (blank)
e.g. Set the IP password to AtlonA
Sets the IP address of the controlled device X= ip, sta
e.g. Display the IP address of the controlled device
Sets the IP port of the controlled device X= port, sta
e.g. Set the IP port to 24
Enable or disable display auto off X= on, off, sta
Enable or disable display auto on X= on, off, sta
Sets how long after receiving no signal to trigger auto
display off X= 1-240, sta
Set delay time for the display on command to be sent
X= 0-300, sta
Note: Match the timing to the projector's delay settings
Set period of time after the display is turned on that the
power command will not send X= 0-300, sta
Set the control type/device the volume button sends out
X= 0-2
Set the control type/device the display button sends out
X=0-3
Locks/unlocks the front panel display key X= on, off, sta
Sets the display command type to RS-232 X= on, off, sta
Sets the display command type to CEC X= on, off, sta
Sets the display command type to TCP/IP X= on, off, sta
Triggers the currently set command type to send display
commands
e.g. if RS-232 is selected the RS-232 on command will send
3 IP
18
Toll free: 1-877-536-3976
Local: 1-408-962-0515