Atlona AT-HDVS-200-TX User Manual page 17

Commands
Command
Type
Version
Mreset
Update X
Input X
e.g. Input HDMI 1
AutoSW X
e.g. AutoSW on
ASwPrePort X
ASwOutTime X
e.g. ASwOutTime 60
ASwFstTime X
e.g. ASwFstTime 10
VGAAuto
HDCPSet1 X
e.g. HDCPSet1 on
HDCPSet2 X
e.g. HDCPSet2 off
PrefTimg X
VGAPrefT X
VOUT1 +
e.g. VOUT1 +
VOUT1 -
e.g. VOUT1 -
VOUT1 X
e.g. VOUT1 -10
VOUTMute1 X
e.g. VOUTMute1 on
Bass X
e.g. Bass +
Treble X
e.g. Treble -5
FreeRun X
e.g. FreeRun on
Each command is terminated with a carriage return.
Feedback is terminated with a carriage return and line feed.
Note: If the command fails or is incorrect the feedback should be "Command FAILED"
Preferred Timings
0 Default
5 1920x1200
10 3840x2160
Preferred Timings
0 Default
5 1920x1200
atlona.com
Feedback Description
Type Displays the model number of the unit
Version Displays the bootcode and firmware version
Mreset Reset the unit to factory settings and restarts the switcher
Update X Sets the unit into update mode X= MCU (unit) or VSTX (Valens)
Input X Select the input device. X= HDMI 1, HDMI 2, VGA, or sta
e.g. Input HDMI 1 e.g. Set the input to HDMI 1
AutoSW X Enable/Disable auto switching or display auto switching status
e.g. AutoSW on e.g. Turns auto switching on
Sets input the switcher defaults to when losing AV signal
ASwPrePort X
X= 1-3, Prev
Sets the delay time for how long the auto switching receives no signal
ASwOutTime X
from the input before switching ports x= 1-600 (default is 1 second)
e.g. ASwOutTime 60
e.g. Sets the delay time to 1 minute with no signal before changing ports
ASwFstTime X Sets the delay time of switching when a new device is powered on
X=10-600
e.g. ASwFstTime 10 e.g. HDVS will switch to the new source after 10 seconds of signal
VGAAuto Adjusts VGA picture to the center of the display
Note: Only valid when VGA is selected
HDCPSet1 X Set HDCP reporting for HDMI IN 1 X= on, off, sta
e.g. HDCPSet1 on e.g. Set HDCP reporting for HDMI IN to compliant
HDCPSet2 X Set HDCP reporting for HDMI IN 1 X= on, off, sta
e.g. HDCPSet2 off e.g. Set HDCP reporting for HDMI IN to non-compliant
PrefTimg X Set preferred timing to EDID. X= 0-10 & sta
VGAPrefT X Set preferred VGA timing to EDID X= 0-8 & sta
VOUT1 XX Increase the volume output by 1
e.g. VOUT1 -5 e.g. Increases the volume output by 1
VOUT1 XX Decrease the volume output by 1
e.g. VOUT1 -20 e.g. Decreases the volume output by 1
VOUT1 X Set the volume to a specific level from -80 to 0
e.g. VOUT1 -10 e.g. Set the volume to -10
VOUTMute1 X Mute/unmute all audio output X= on, off, sta
e.g. VOUTMute1 on e.g. Mute all audio output
Bass X Adjusts the bass of the audio output X= +, -, sta, -12 to 15
e.g. Bass 5 e.g. Increases the bass by 1
Treble X Adjusts the treble of the audio output X= +, -, sta, -12 to 15
e.g. Treble -5 e.g. Sets the treble to -5
FreeRun X Sets whether analog audio will pass on without video X= on, off, sta
e.g. FreeRun on e.g. Sets the analog audio to pass through without video
-
(HDMI)
1 1280x800 2 1920x1080
6 1366x768 7 800x600
sta
-
(VGA)
1 1280x800 2 1920x1080
6 1366x768 7 800x600
3 1024x768
8 1600x900
3 1024x768
8 1600x900
17
4 1280x720
9 2560x1440
4 1280x720
sta
Toll free: 1-877-536-3976
Local: 1-408-962-0515