Assigning Functions To User Buttons; Selectable Functions - Panasonic AJ-PX380G Operating Instructions Manual

Assigning functions to USER buttons

Selected functions can be assigned to the <USER MAIN>, <USER1>, <USER2>, and lens <RET> buttons.
Set each function to be assigned in the main menu → [USER SW], [USER MAIN], [USER1], [USER2], [RET SW].
In the factory settings, [Y GET] is assigned to the <USER MAIN> button, [TEXT MEMO] to the <USER1> button, [LEVEL GAUGE] to the <USER2>
button, and [REC CHECK] to the <RET> button of the lens.

Selectable functions

The functions that can be assigned to the USER button are as follows:
Item
[INHIBIT] Disables assignment of functions.
[LEVEL GAUGE] Assigns the function for switching the level gauge display function to enabled/disabled.
[LEVEL GAUGE Assigns the function to set the level gauge using the current horizontal and vertical directions as reference values. Holding down the
RESET] assigned button will reset to the factory setting.
Assigns the function for switching the waveform display of the waveform monitor. Select the waveform display from the main menu →
[WFM]
[SW MODE] → [WFM MODE].
[D.ZOOM x2] Assigns the digital zoom function.
[D.ZOOM x4] Zooms in on the field angle by 2x/4x vertically and horizontally.
[DRS] Assigns the function for switching the dynamic range stretcher function to enabled/disabled.
[FBC] Assigns the function for switching the flash band compensation function to enabled/disabled.
[S.GAIN] Assigns the function for switching the super gain function to enabled/disabled.
[ATW] Assigns the function for switching the auto tracking white balance function to enabled/disabled.
Fixes the white balance value when pressing this item while the auto tracking white balance function is activated. Resumes the auto
[ATW LOCK]
tracking white balance function when pressing again.
[SPOTLIGHT] Assigns the function for switching the auto iris control function for the spotlight to enabled/disabled.
[BACKLIGHT] Assigns the function for switching the auto iris control for the backlight compensation to enabled/disabled.
[Y GET] Assigns the function for displaying the brightness level of the frame area displayed near the center.
[PRE REC] Assigns the function for switching the pre-recording function to enabled/disabled.
[TEXT MEMO] Assigns the text memo function.
[SHOT MARK] Assigns the shot mark function.
[DEL LAST CLIP] Assigns the function to delete the clip shot immediately beforehand.
[SLOT SEL] Assigns the function for switching the card to record when multiple cards are inserted in the microP2 memory card slot.
Assigns the function to select the recording target slot between the P2 memory card slot and microP2 memory card slot. This setting is
[REC MEDIA]
linked to the setting value in the main menu → [RECORDING SETUP] → [REC MEDIA].
Assigns the function for switching the output audio channel. If audio channel 1/2 is selected, every press of the assigned button switches
the channel between audio channel 1 monaural, audio channel 1 and 2 stereo, and audio channel 2 monaural. If audio channel 3/4 is
[AUDIO MON SEL]
selected, every press of the assigned button switches the channel between audio channel 3 monaural, audio channel 3 and 4 stereo, and
audio channel 4 monaural.
[REC CHECK] Assigns the recording check function.
[CAM RET] Return video function is enabled. The signal supplied to the <SDI OUT2/IN> terminal is displayed on the viewfinder while the switch is
pressed. Use by setting the main menu → [IN/OUT SEL] → [SDI OUT2/IN SEL] to [SDI IN].
[BS CALL] The <TALLY/CALL> lamp in AG-BS300P/AG-BS300E is illuminated while the switch is pressed. This is assigned when the AG-BS300P/
AG-BS300E is connected directly and used as an extension system.
[TALK] By pressing the button to enable, the INCOM headset microphone is enabled and talking to the AG-BS300 side becomes possible.
[USB MODE] Assigns the function for switching the USB device mode or USB host mode to enabled/disabled.
[PLAYLIST] Assigns the function for switching the playlist edit mode to transfer/end.
[REC DURING Assigns the function for enabling/disabling the rec during upload function.
UPLOAD] This setting is linked to the setting value in the main menu → [NETWORK SETUP] → [FTP CLIENT SERVICE] → [REC DURING
UPLOAD].
[UPLOAD LIST] Assigns the function to display the upload list of the rec during upload function. To close the upload list, press the <EXIT> button.
[STREAMING Assigns the function for starting/stopping streaming from the camera.
START] This setting is linked to the setting value in the main menu → [NETWORK SETUP] → [STREAMING SETTING] → [START].
[EVF COLOR] Assigns the function for switching whether to display the viewfinder image in color or in black and white.
Chapter 4 Shooting — Assigning functions to USER buttons
<USER MAIN>/<USER1>/<USER2> buttons
– 66 –
Description