Panasonic AJ-PX380G Operating Instructions Manual page 213

Display
[PROXY ERROR]
[PROXY REC WARNING]
[REC IMPOSSIBLE] (slot number)
[REC WARNING]
[FRAME SIGNAL]
[REC WARNING]
[OVER MAX# CLIPS]
[REC WARNING]
[PULL DOWN]
[REC WARNING]
[PULL DOWN ERROR]
[REC WARNING]
[REC DATA]
[RUNDOWN CARD] (slot number)
[SD CARD] (slot number)
[SLOT3 CANNOT REC]
[microP2 SELECTED]
[SLOT3/4 CANNOT REC]
[P2 SELECTED]
[TEMPORARY PAUSE]
[IRREGULAR SIG]
[WIRELESS-RF]
During thumbnail and menu operation
Display
[AUTHENTICATION ERROR!]
[CANNOT ACCESS!]
[CANNOT CHANGE!]
[CANNOT DELETE!]
[CANNOT FORMAT!]
[CANNOT RE-CONNECT!]
Chapter 11 Maintenance — Warning system
Description
An error occurred in the internal proxy module.
A proxy data recording error occurred.
An SDHC/SDXC memory card is inserted into the P2
memory card slot.
Recording to the SDHC/SDXC memory card is disabled.
Displayed when a video or audio error occurs during
recording.
f Tally lamp flashes four times per second during
continuous recording.
Displayed when attempting to record in excess of the
maximum total number of clips allowed for one P2 card.
f The tally lamp and <WARNING> lamp flash four times
per second during continuous recording.
Displayed after approximately 3.5 hours has elapsed
from the time when operation to start a single recording
is executed when [SHORT SPLIT] is selected in the
main menu → [RECORDING SETUP] → [FILE SPLIT].
(Occurs during recording)
The video pull-down sequence and time code values
are not synchronized.
f Tally lamp flashes four times per second during
continuous recording.
(Occurs at times other than during recording)
The video pull-down sequence and time code values
are not synchronized.
Displayed when an error occurs in recorded data during
recording.
f The tally lamp and <WARNING> lamp flash four times
per second during continuous recording.
The maximum number of overwrites has been
exceeded.
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
Displayed when the card is inserted into the slot which
is not selected as the recording slot.
Displayed when the card is inserted into the slot which
is not selected as the recording slot.
Correct recording is not possible due to disruption
of input signals of the <GL IN/VIDEO OUT> or <SDI
OUT2/IN> terminal, etc., and recording is suspended
temporarily. The clip will be divided.
f Tally lamp flashes four times per second during
continuous recording.
Audio wireless reception status is poor.
f The tally lamp flashes four times per second during
continuous recording.
f The <WARNING> lamp flashes four times per second
during continuous recording and recording standby.
Description
Manual authentication failed.
Data cannot be accessed due to a content defect or
some other reason.
For a clip with the mark, where a thumbnail cannot
be generated, the thumbnail cannot be modified in the
text memo position.
The content versions do not match. Cannot delete.
A P2 card problem or some other reason prevents
formatting.
Clips cannot be remerged because either clips not
recorded across multiple P2 cards are selected or other
reasons.
– 213 –
Behavior and cause
f The current operation will continue.
f Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
f The current operation will continue.
f Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
f The current operation will continue.
f Record to microP2 or P2 memory cards.
f The current operation will continue. When input
signals are disrupted, recording continues while
disrupted images are recorded. Check the signal to be
input to the camera.
f Turn off the power and on before using it again.
f The operation will stop.
f Replace the P2 card or delete unnecessary clips.
f The operation will stop.
f The current operation will continue.
f Check the signal.
f The current operation will continue.
f Check the signal.
f The operation will continue or stop.
f Turn off the power and on before using it again.
f The current operation will continue.
f Replacement of the P2 card is recommended.
f The current operation will continue.
f Use of microP2 or P2 memory card is recommended.
f The operation stops.
f Set the main menu → [RECORDING SETUP] → [REC
MEDIA] to [P2].
f The operation stops.
f Set the main menu → [RECORDING SETUP] → [REC
MEDIA] to [microP2].
f The operation will pause.
f Recording resumes when the signal returns to normal.
However, during loop recording, recording does not
resume.
f The current operation will continue.
Behavior and cause
Enter the correct password.
Ensure the health of the media and the clips.
Correct the settings and content to enable display of the
thumbnail.
Match the device and contents version.
Check the P2 card.
Check the selected content.