Even if the display is set to [OFF], only [REC], [START], and [END] are displayed. Also, when pre-recording, loop recording, interval recording, or one-shot

recording is set, it is displayed.

Displayed when [INTERVAL], [ONE SHOT], or [LOOP] is set in the main menu → [RECORDING SETUP] → [RECORDING], or when [ON] is set in the

main menu → [RECORDING SETUP] → [PRE REC].

41 Rec during upload status display

Displays the status of rec during upload.

f [ ]: Displayed when the rec during upload function is enabled.

The display will blink when recording is started immediately after the power is turned on or the P2 card is inserted, and the upload will not be

performed until the recording is stopped.

f [ ]: Displayed during upload.

f [ ]: Displayed from when transfer error occurred during upload until when the next upload starts.

42 Streaming distribution status display

Displays the streaming status.

f [

] (blinking): Blinks while the camera is being connected to a device which will receive the streaming video.

f [

] (illuminated): Displayed when the camera is connected to a device receiving the streaming video and the camera is transmitting streaming

video.

The display turns off when a connection could not be established properly.

NOTE

t Depending on the network status, the [

43 High-sensitivity mode display

Displayed when [HIGH SENS.] is set in the main menu → [SYSTEM MODE] → [SHOOTING MODE].

44 HD SDI REMOTE recording status and 4G/LTE connection status

Displays the control status of whether recording has started or stopped for an external device which is connected to the <SDI OUT1> terminal.

When [ON] is set in the main menu → [IN/OUT SEL] → [HD SDI REMOTE], the status will always be displayed regardless of the setting in the main

menu → [DISPLAY SETUP].

f [SDIn]: Status where the recording is being instructed for an external device

f [SDI&]: Status where recording stop is being instructed for an external device

Displays the 4G/LTE connection status. Displays at the 4G/LTE connection. Displays the strength of the signal reception in six levels. Displays the

radio wave strength with the number of vertical bars. It is not displayed when the setting of 4G/LTE is disabled.

f [4G/LTE

]: During 4G/LTE connection

f [4G/LTE

]: When not connected with4G/LTE

f [4G/LTE

]: When there is a problem with the 4G/LTE connection

NOTE

t Depending on the USB modem that is supported, vertical bars that indicate the signal strength may not be displayed.

Camera status display

These are indicated in the information display area in the center.

[ABB]: Displayed while automatic black balance operation is active.

[ATW MODE]: Displayed when the <AUTO W/B BAL> switch is pushed to the <AWB> side while auto tracking white balance is active. This is also

displayed when the <WHITE BAL> switch is turned to <B> if [ATW] is allocated.

[AWB]: Displayed while automatic white balance operation is active.

[WHITE:PRE ****K]: Displays the set color temperature when the <WHITE BAL> switch is switched.

[AWB PRESET ****K]: Displayed when the <WHITE BAL> was set to <PRST> in an attempt to execute automatic white balancing.

[BACK LIGHT]: Displayed when pressing the USER button to which [BACKLIGHT] is allocated for iris control, and switching the status.

[GAIN**dB]: Displayed when gain is switched.

[SHUTTER 1/****]/[SHUTTER OFF]: Displayed when you switch the shutter speed.

[SPOT LIGHT]: Displayed when pressing the USER button to which [SPOTLIGHT] is allocated for iris control, and switching the status.

Checking and displaying the shooting status

Also, the mode check [STATUS] screen is displayed when the <DISP/MODE CHK> switch is pushed towards the <CHK> side. During mode check,

almost all items are displayed including usually hidden items so that the shooting status can be checked. For details on the mode check, refer to "Mode

check display" (page 169).

The list shows the display/hide status of each item in the [STATUS] screen. The display/hide status differ depending on the <DISP/MODE CHK> switch

settings and settings in the main menu → [DISPLAY SETUP] → [OTHER DISPLAY].

f "l" indicates displaying, and "—" indicates hiding.

f [ON]/[OFF] for each item can be selected in the main menu → [DISPLAY SETUP] → [DISPLAY SETTING].

Item

Time code display

Frame rate display

Proxy information display

SD memory card status display

System mode display

Chapter 8 Display — Screen status display