[Network Setup] - Panasonic AJ-PX380G Operating Instructions Manual

Item
[GENLOCK SETTING] [GL PHASE]
[H PHASE]
[DOWNCON SETTING] [DETAIL]
[H.DTL LEVEL]
[V.DTL LEVEL]
[DTL CORING]
[H.DTL FREQ]
[MON OUT ZEBRA]
[TC IN/OUT SEL]
[TC OUT]
[TC OUTPUT REF]

[NETWORK SETUP]

Configure the settings regarding the network.
Item
[USB MODE SELECT]
[USB MODE]
[NETWORK SEL]
[NETWORK FUNC] [HTTP SERVER]
Chapter 6 Menu Operations — Menu list
When in HD (1080P, 1080i, 720P) mode, selects the output signal of phase to be locked to the signal input
to the <GL IN/VIDEO OUT> terminal.
[HD SDI]: Locks the HD SDI output signal to genlock input.
[COMPOSITE]: Locks the down-converted composite output signal (480i or 576i signal from <GL IN/
VIDEO OUT> terminal) to genlock input.
f Factory setting: [HD SDI]
Adjusts the horizontal phase when the phase is to be locked to the signal input to the <GL IN/VIDEO
OUT> terminal.
[−512]...[512]
f Factory setting: [0]
Turns detail function for the down converter output signal [ON]/[OFF].
[ON], [OFF]
The down converter output signal contains detail components set during HD signal processing.
This setting superimposes the detail components exclusive to down converter output to that signal.
f Factory setting: [ON]
Sets horizontal detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [8]
Sets vertical detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [4]
Sets the detail noise removal level.
[0]...[15]
f Factory setting: [1]
Selects the horizontal detail frequency.
[2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz]
f Factory setting: [3.5MHz]
Selects whether the zebra pattern is superimposed over the output video signals from the monitor output
terminals (<HDMI>, <SDI OUT2/IN>, and <GL IN/VIDEO OUT>).
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
The video signal output from the <SDI OUT1> terminal will be a candidate for selection when [MON
ZEBRA] is selected in the main menu → [IN/OUT SEL] → [SDI OUT1 ZEBRA].
Selects whether to use the <TC IN/OUT> terminal for input or for output.
[TC OUT]: Uses as output.
[TC IN]: Uses as input.
f Factory setting: [TC OUT]
Sets the type of time code output from the <TC IN/OUT> terminal.
[TCG]: Outputs the time code generator value of the camera at all times.
[TCG/TCR]: Outputs the time code generator value for camera image output, and the time code value of
the video being played back for video playback output.
f Factory setting: [TCG]
Sets the output delay of time code output from the <TC IN/OUT> terminal.
[RECORDING]: Outputs the recorded time code with no delay. This is used when performing simultaneous
recording on two cameras with the time code of this camera as the master.
[MON OUT]: Matches to output image.
f Factory setting: [MON OUT]
Sets the camera operation mode when an external device is connected to the USB.
[STORAGE]: Sets the mode to be used with connected devices such as an external hard disk drive.
[DEVICE]: Selects the USB device mode for using P2 cards as mass storage, using computers or other
devices connected via USB 2.0.
f Factory setting: [STORAGE]
Enables/disables the mode selected in [USB MODE SELECT].
[ON], [OFF]
f Factory setting: [OFF]
Sets the connection method when connecting the camera with an external device (such as a computer) via
network.
[WLAN]: Connects via wireless LAN.
[4G/LTE]: Connects via 3G/4G/LTE.
[LAN]: Connects via the <LAN> terminal.
[OFF]: Does not connect.
f Factory setting: [OFF]
Configures the settings regarding the HTTP server.
[BROWSE]: Enables the P2 browser function.
[BROWSE (+CTRL)]: Enables the HTTP server function, starting and stopping recording at the terminal
side, and preset control of time code or user bits.
[DISABLE]: Disables the HTTP server function.
f Factory setting: [DISABLE]
– 144 –
Description of settings
Description of settings