If any of these lines is detected while an image signal is being received, the RTN signal will be transmitted after receiving the protocol signal of the transmitting

party. Higher parameters restrict the transmission of the RTN signal.

16.5.3 <005: NCC pause length (pre-ID code)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the length of the pause automatically entered between access code and ID code when the NCC (New Common Carrier) line is used for dialing.

16.5.4 <006: NCC pause length (post-ID code)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the length of the pause automatically entered between ID code and telephone number of the other party when the NCC (New Common Carrier) line is

used for dialing.

16.5.5 <010: line connection identification length>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the time for identifying the line connection. Raise this parameter if errors occur frequently at time of communication because of the condition of the line.

Memo:

Any of the following error codes may be indicated because of the condition of the line

##0005, ##0018

The line condition identification time is between when the dial signal is transmitted and when the line condition is cut for the transmitting party, while it is between

when the DIS signal is transmitted and when the line is cut for the receiving party.

16.5.6 <011: T.30 T1 timer (for reception)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Set the T1 timer for the receiver (wait time after DIS transmission starts until a significant signal is received).

16.5.7 <013: T.30 EOL timer>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Set it so that the 1-line transmission time is longer for reception to prevent reception errors caused by a long data length per line (e.g., computer FAX).

16.5.8 <015: hooking detection time>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Allows setting of the hooking detection time.

16.5.9 <016: time length to first response at time of fax/tel switchover>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Allows setting of the time from seizing the line till pseudo RBT is sent, when the Fax/ Tel switching function is operating.

16.5.10 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:

pseudo RBT signal pattern OFF time length (long)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the pattern of the pseudo RBT signal transmitted at time of a fax/tel switchover.

16.5.11 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:

pseudo CI signal pattern OFF time length (long)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the pseudo CI signal pattern transmitted at time of a fax/tel switchover.

16.5.12 <023: CNG detention level for fax/tel switchover>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the CNG detention level for a fax/tel switchover.

16.5.13 <024: pseudo RBT transmission level at time of fax/tel switchover>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to set the pseudo transmission level for a fax/tel switchover.

16.5.14 <025: Answering machine connection function signal detection time>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Sets the signal detection time for the answering machine connection function operation. When the answering machine connection function is operating, if the func-

tion does not operate normally because the fax does not detect CNG signal sent from the line, raise this parameter to increase the signal detection time.

16.5.15 <027: V.21 low-speed flag preamble identification length>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Use it to detect the time of detection after which command analysis is started after detecting V.21 low-speed command preambles continuously for a specific period

16-18

0013-1342

0013-1343

0013-1344

0013-1345

0013-1346

0013-1347

0013-1348

0013-1349

0013-1350

0013-1351

0013-1352